2021 SP12: Важные улучшения и исправления

Tekla Structures
2021
Tekla Structures

2021 SP12: Важные улучшения и исправления

Последние обновленные установщики сред и пакеты обновлений Tekla Structures можно загрузить с Tekla Downloads.

Замена таблиц в компоновке чертежа

С помощью новой команды контекстного меню Редактор компоновок Заменить таблицу можно заменять таблицы в компоновке. Чтобы заменить таблицу, щелкните таблицу в компоновке правой кнопкой мыши и выберите Заменить.

При замене таблицы сохраняются все настройки, заданные для таблицы, которую вы заменяете. Новая команда устраняет необходимость сначала удалить таблицу в компоновке, а затем добавить новый шаблон, задать точку привязки и выравнивание и наконец связать другие таблицы с новой.

TTSD-41881

Усовершенствования в экспорте в ELiPLAN (68)

Усовершенствования в дренажных отверстиях

  • Параметр создания дренажных отверстий перенесен со вкладки Дренажные отверстия на вкладку Данные плоттера.
  • Теперь можно задать следующие смещения на новой вкладке Дренажные отверстия:

    • Смещение для дренажных отверстий на боковых выемках с помощью нового варианта На стороне углубления/проема.
    • Смещение для дренажных отверстий на углублениях или проемах с помощью нового варианта В конечных зонах углублений/проемов.
    • Смещение для дренажных отверстий на монтажных петлях с помощью нового варианта На монтажных петлях.
    • Смещение для дренажных отверстий на вырезах с помощью нового варианта На вырезах.
  • Кроме того, теперь можно объединять дренажные отверстия, если они находятся в пределах расстояния, указанного для нового варианта Объединить дренажные отверстия ближе чем.

TSAC-6923, TSAC-6100, TSAC-6089, TSAC-6945, TSAC-6927, TSAC-6921

Экспортировать внутренние пустоты пустотных элементов

Внутренние пустоты пустотных элементов теперь можно экспортировать с помощью нового параметра Экспорт внутренних пустот на вкладке Данные плоттера.

TSAC-5385

Открыть экспортированный файл

После завершения обработки теперь можно открыть экспортированный файл в соответствующем приложении с помощью нового параметра Открыть экспортированный файл после обработки на вкладке Параметры.

TSAC-7381

Автоматическое распознавание принадлежностей по форме

Для параметра Размечать вырезы/закладные теперь можно использовать новый вариант Автоматически на вкладке Данные плоттера для автоматического распознавания принадлежностей по форме.

TSAC-7297

Усовершенствования в экспорте в Unitechnik (79)

Теперь можно указать, поменять ли местами оболочки двуслойной стены, с помощью нового параметра Разрешить замену оболочек на вкладке Конфигурация TS.

TSAC-6605

Исправлений

Номер дефекта Район застройки Описание
TSAC-4203 Concrete components

Braced girder (88): Previously, the braced girder was not split and it did not continue when it reached the recesses. This issue has now been fixed.

TSAC-5960 Concrete components

Concrete console (110): The polygon cut to cut the column is now created properly with sloped beams.

TSAC-6127 Concrete components

Concrete console (110): Previously, the hole position was not correct in the neoprene when it was placed under a sloped beam. This issue has now been fixed.
 

TSAC-6628 Concrete components

Corbels and recesses (82): Recess positioning for cut parts has been improved.

TSAC-6958 Concrete components

Concrete beam-beam (112): Previously, beam cuts, anchors, and neoprene were not created correctly when there was a combination of polygonal neoprene and sloped beams. This issue has now been fixed. In addition, split neoprene is now created correctly.

TSAC-7003 Concrete components

Concrete beam-beam (112): The cut around the anchor bottom tube is now aligned properly to the top of the secondary part when the Tubes aligned with setting is set to Top of secondary on the Anchors tab.

TSAC-7007 Concrete components

Braced girder (88): Previously, girders were not created correctly if there was a cutout or a partial cutout on one or both of the side edges of the main part. This issue has now been fixed.
 

TSAC-7031 Concrete components

Rebar coupler and anchor tools: The Extra fabrication length values are now written to the correct user-defined attributes.

TSAC-7035 Concrete components

Electric box in wall (84): Sometimes, when you changed the connection used between the electric parts and the panel, the result assembly of the parts was broken. This issue has now been fixed.
 

TSAC-7039 Concrete components

Concrete foundation (1030): The height level of the inner tube rebar is now properly defined.

TSAC-7176 Concrete components

Embedded anchors (008): Numbering now works properly for the extra insulation part.

TSAC-7299 Concrete components

Lifting anchor (80): Previously, lifting anchors were not created properly when created on an inconsistent assembly. This issue has now been fixed.

TTSD-55092 Concrete components

Embedded anchors (008): Earlier, when using a component for creating anchors in the Embedded anchors (008) component, there could be an application error in Tekla Structures. This issue has now been fixed.

TSAC-5988 Steel components

Haunch (40): Main part stiffeners are now created correctly when the column profile has flange slope ratio.

TSAC-6115 Steel components

Stiffened end plate (27): The default value of the front plate height is now the same as the end plate height in the column to beam connections.

TSAC-6149 Steel components

Column tube seating (100): Previously, the plate profile prefix did not respect the settings in File menu > Settings > Options > Components > Profile name. This issue has now been fixed.

TSAC-6294 Steel components

Railings (S77): Previously, only 99 vertical rails were welded to the main part. This issue has now been fixed and all rails are welded correctly to the main part.

TSAC-6306 Steel components

Stiffeners (1003), Multiple stiffeners (1064): Previously, weld preparations were always created. This issue has now been fixed.

TSAC-6308 Steel components

Seating cap plate (2): Previously, the horizontal offset of the lower cap plate was not correctly applied. This issue has now been fixed.

TSAC-6355 Steel components

Ring plate: The part and assembly start number of the ring plate are now modified when only the corresponding check boxes are selected. Previously, the part and assembly start number were not modified unless all the check boxes in the dialog box were selected.

TSAC-6356 Steel components

Opening frame: The On plane and At depth offset values on the Parts tab for top frame, bottom frame and vertical posts are length values and they now use the correct units set in Options > Units and decimals. The Angle value for welds and Rotation angle on the Parts tab are angle values and they now use the correct units set in Options > Units and decimals.

TSAC-6588 Steel components

Railings (S77): Previously, when stanchions were sloped with a minor angle, the top horizontal rail was not created correctly. This issue has now been fixed.

TSAC-6637 Steel components

Clip angle (141): Previously, the vertical bolt edge distance was not correctly applied in some cases. This issue has now been fixed.
 

TSAC-6806 Steel components

Column with stiffeners W (182): Previously, the strip to the secondary part flange did not work when the secondary part was connected to the main part web. This issue has now been fixed.

TSAC-6894 Steel components

Open/close angle ends (1050): The component performance with polybeams has been improved.

TSAC-6955 Steel components

UltraZED File transfer (93): Previously, manually adjusting the length of a diagonal restraint after they had been inserted with a component resulted in incorrect CAM data as it would not update. Now, the Tekla Structures displays a warning message, and requests drawings.

TSAC-7000 Steel components

Wall rails: You can now set different materials for the bracket arm and bracket base.

TSAC-7001 Steel components

Ayrshire Diagonal tie - column (81), Ayrshire File transfer (92): Previously, there was an application error when connecting the diagonal brace to a column or rafter. This issue has now been fixed.

TSAC-7017 Steel components

The Auto bolt component used in custom components now supports the following data types for the BoltSize attribute: bolt size, length, double, and string. The component can also be modified while being a part of custom component, in the user interface, without any unexpected results. The stand-alone Auto bolt component works the same way as previously.

TSAC-7030 Steel components

Steadmans Mezzanine inset cleat (121) is a new inset cleat connection for the mezzanine floor range of beams.

TSAC-7067 Steel components

Bolted gusset (11), Tube gusset (20): Previously, the weld between the gusset and the base plate was not created at all in some cases. This issue has now been fixed.

TSAC-7082 Steel components

Cast-in plate (1069): Previously, the tab plate material was not applied correctly. This issue has now been fixed.

TSAC-7109 Steel components

Gusset+ T: The stiffener chamfer is now created to the web of the main part.

TSAC-7115 Steel components

Circular base plate (1052): Previously, anchors were created with incorrect placement and they clashed with the base plate when grout had been created. This issue has now been fixed.

TSAC-7118 Steel components

Tensioner (7): Previously, the component did not work correctly for one secondary part. This issue has now been fixed.
 

TSAC-7148 Steel components

Two sided clip angle (143): Previously, the vertical position of bolts was affected by the notch cuts in the secondary parts. This issue has now been fixed.

TSAC-7164 Steel components

Generation of purlins (50): Previously, connections were not created on both sides of the last roof beam. This issue has now been fixed.

TSAC-7201 Steel components

Shear plate simple (35): Previously, the assembly position and start number were incorrectly applied for the shear tab. This issue has now been fixed.

TSAC-7220 Steel components

Seating (39): Previously, only one pair of stiffeners was created for some of the main part profiles. This issue has been fixed, and two pairs of stiffeners are now created.

TSAC-7223 Steel components

Joining plates (14): Previously, when the angle between the main and secondary part was small, the component did not work correctly. This issue has now been fixed.

TSAC-7236 Steel components

Clip angle (141): Previously, the vertical position of bolts was affected by the notch cuts in the secondary part. This issue has now been fixed.

TSAC-7240 Steel components

Stiffened end plate (27): On the Parts tab, you can now select whether the front plate is moved in column to beam connections.

TSAC-7303 Steel components

U.S. Base plate (1047): Previously, the cuts to create finger shim plates were not positioned correctly. This issue has now been fixed.

TSAC-7332 Steel components

Base plate (1042): Previously, the component was not rotated when you changed the Up direction on the General tab. This issue has now been fixed.

TTSD-8330 Organizer

Organizer object group (.OrgObjGrp) files can now be read from the subfolders of firm or project folders in the Organizer category properties dialog box.

TTSD-54093 Import, export, interoperability

Base points: Previously, base points with empty name were sometimes saved. This has now been fixed.

TTSD-54476 Import, export, interoperability

IFC2x3 export: Due to some invalid fittings, the IFC2x3 export behaved incorrectly when trying to apply these fittings in a certain base point use case. Now invalid fittings are ignored in the IFC2x3 export.

TTSD-54947 Import, export, interoperability

Radial grids in the exported .tekla reference models were sometimes incorrect. This issue has now been fixed.

TTSD-55036 Import, export, interoperability

Point clouds: The point cloud location was not modified and saved correctly in a specific use case, which has now been fixed.

TTSD-55134 Import, export, interoperability

IFC4 export: With the Export flat wide beams as plates setting, plates were sometimes exported to wrong location. This issue has now been fixed.

TPLED-263 Templates and reports

Template Editor: Previously, if the value field was center-aligned and you changed the length of the field, the center point of the value field moved. Also, if the value field was right-aligned and the length was changed, the value field position did not work correctly. This issue has now been fixed.

TPLED-266 Templates and reports

Template Editor: Sometimes automatic line wrapping caused value fields with multiple lines to not show the cut value indicator "***". This issue has now been fixed.

TPLED-269 Templates and reports

Template Editor: When you panned the template work area with the mouse, the selection handles were drawn with the background color and the handles were invisible. This issue has now been fixed.

TPLED-273 Templates and reports

Template Editor: Copying and pasting a text object that has the '$' character as its only content fails. This issue has now been fixed.

TTSD-52195 Templates and reports

Tekla Structures stopped responding when a template tried to output a single row that was defined to use columns that started from bottom left or bottom right. This issue has now been fixed.

TSAC-6979 Drawings

View-specific dimensioning: The drawing dimensioning method Filter did not work correctly in skewed cases when dimensioning custom components as secondary objects. This issue has now been fixed.

TSAC-7175 Drawings

View-specific dimensioning: When the dimensioning method Filter was used for skewed edges and the cast unit consisted of several parts, the dimension start and end points were not always placed correctly. This issue has now been fixed.

TTSD-53541 Drawings

Adding an associative note for the selected part did not work correctly if you picked the leader line positions outside the drawing view. This issue has now been fixed.

TTSD-53989 Drawings

Drawing context menu: Now the context menu in drawing mode is updated and shown correctly when you click the model view while editing a drawing and then return back to the drawing. Earlier, the context menu was empty in this case.

TTSD-54698 Drawings

Earlier, in neighbor parts with bolt holes, circular holes could get a slotted hole mark. This issue has now been fixed.

TTSD-54819 Drawings

Earlier, when inserting or modifying marks with the advanced option XS_ENABLE_REBAR_MARK​_LEADER_​LINE_BASE_​​POINT​_OPTIMIZATION set to TRUE, the base point optimization was also done for other types of marks than rebar marks. This issue has now been fixed.  

TTSD-54839 Drawings

Earlier, when you moved drawing views to another drawing, and one or several text objects were also selected, Tekla Structures stopped responding. This issue has now been fixed.

TTSD-54388 Tekla Model Sharing

Now, in Tekla Model Sharing, drawing files are restored if the .dg files have been accidentally deleted. Deleted drawings are copied to the ModelSharing\BackUpEnv folder and are checked against to the drawings on the Drawing list. The .dg files are read automatically from the BackUpEnv folder when another user reads in the packet that has been written out after the drawing deletion.

TTSD-54524 Tekla Model Sharing

Previously, reading in the sharing changes was sometimes extremely slow if the model contained a large number of custom components that had been duplicated from plugin components with an identical name. A warning dialog box was shown, and you had to click the OK button multiple times on the dialog box to pass the warnings and being able to continue.

Now, the components are no longer automatically updated when you read in. This results in faster performance and fewer false modification conflicts, and no warnings are shown. 

TTSD-51539 Modeling

Now, when multiple bent plate or lofted plate parts in a component are updated, the corresponding existing object is identified more reliably. 

TTSD-54170 Modeling

Previously, if multiple parts were selected and one of the parts had a parametric profile, the profile was shown as invalid in the property pane. This now has been fixed.

TTSD-54331 Modeling

Previously, in some rare cases, when assemblies with and without bolt holes were compared, Tekla Structures might have stopped working unexpectedly. This has now been fixed.

TTSD-54587 Modeling

Solid errors occurring with certain sandwich walls have now been fixed.

TTSD-54611 Modeling

Previously, the width and height of parts with sketched profiles was sometimes incorrectly calculated with the reference function fp. This has now been fixed.

TTSD-54716 Modeling

Previously, when modeling and then inquiring negative hole tolerances, the HOLE_TOLERANCE template attribute returned 0 instead of the actual value. This issue has now been fixed.

TTSD-54840 Modeling

If you used the Create shape from geometry command from the context menu, then selected a bolt and pressed Enter, Tekla Structures tried to apply the Create shape from geometry command on the bolt, and then unexpectedly stopped working. This issue has now been fixed.

TTSD-55192 Modeling

Earlier, when performing operations that required unfolding of lofted plates consisting of several close to parallel polygon sections, for example, inquiry or export to IFC4, there was an application error in Tekla Structures. This issue has now been fixed.

TTSD-55674 Modeling

Previously, an empty cross section for weld preparation could cause Tekla Structures to stop working unexpectedly. This has now been fixed.

TTSD-55926 Core

Previously, in some rare situations, Tekla Structures might have stopped working unexpectedly when pressing F1. This has now been fixed.

TTSD-56351 Tools and components

Previously, when a formula or equation for a sub-object was removed in Custom component browser, it became visible again after clicking Refresh. This has now been fixed.

TTSD-53860 Numbering

In some rare cases, when using a negative cut length for bolts, the placement of bolts did not affect numbering. This issue has now been fixed.

TTSD-54302 Numbering

Identical, irregularly spaced reinforcement meshes with cross bars on opposite sides will no longer receive the same position number.

TSAC-7105 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Element corner cuts created by line cuts in the model are now exported with a dedicated type code to the ELiPLAN file.

TSAC-7179 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Now height is also exported for user-defined profiles.

TSAC-7215 Import, export, interoperability (concrete)

Export ELiPLAN file (68): The export of complex walls created by multiple concrete parts has been improved.

TSAC-7290 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Previously, the export of elements with complex geometry did not work correctly. This issue has now been fixed.

Была ли эта информация полезной?
Назад
Далее