Two sided clip angle (143): Previously, the flange cut created due to bolts clashing with the flange was not created for the second secondary beam in all situations. This issue has now been fixed.

Railings (S77): Previously, the top rail was created with an incorrect profile in some situations. This issue has now been fixed.

Railings (S77): Previously, an incorrect fitting was created between the first and last part of the bottom rail and the first and last stanchion. This issue has now been fixed.

Two sided end plate (142): Previously, safety connections were not correctly applied in all situations. This issue has now been fixed.

Gusseted cross (62): Previously, the bolt edge distance on the bracing side was not correctly applied from the joints.def file. This issue has now been fixed.

Simple clip angle (31), Two sided clip angle (33): Previously, when the main part was sloped, the cope cuts were not created correctly. This issue has now been fixed.

Ring plate: Previously, when using two half ring plates, only one weld was created between them. This issue has now been fixed.

Column seating (39): Previously, bolts were not created for specific main part profile and bolt horizontal offset combinations. This issue has now been fixed.

UltraZED Non-std side rail (91): Previously, counterforming both sets of bolts reduced the strut length at one end. This issue has now been fixed.

Stairs (S71): Previously, special holes of bolts were not created in the correct parts. This issue has now been fixed. Special holes are now created in the correct parts as defined in the component dialog box.

Tube gusset (20): Previously, the end plates were not created correctly when the secondary parts had different inclination. This issue has now been fixed.

Stairs (S71): Previously, when you added another component to the top or bottom landing parts, the added component did not affect the correct part. This was caused by IDs swapped between the top and bottom landing parts. This issue has now been fixed.

U.S. Base plate (1047): The Eliminate external bolts setting on the Parameters tab now works correctly again. 

Stiffened end plate (27): Previously, finger shim plates were created incorrectly in some cases. This issue has now been fixed.

End plate (144): Previously, finger shim plates were created incorrectly in some cases. This issue has now been fixed.

Stiffened end plate (27): Previously, one of the shear tab corner chamfers was not created correctly. This issue has now been fixed.

Base plate (1004): Previously, grout slope cuts were causing a clash with the base plate. This issue has now been fixed.

Multiple stiffeners (1064): Previously, the component did not work correctly for main parts created as composites of welded parts. This issue has now been fixed.

Base plate (1004): Previously, deleting bolts did not work correctly when bolts were placed below the main part. This issue has now been fixed.

Corner wrapped gusset (63): Previously, the gap distance between the gusset plate edge and the main part was not correctly applied. This issue has now been fixed.

Multiple stiffeners (1064): Previously, welds were not created correctly when the main part was created as a composite of welded parts. This issue has now been fixed.

Previously, category properties did not open if the environment or model did not have any Organizer filters. This issue has now been fixed.

Earlier, when you had set XS_BOLT_DUPLICATE_IGNORE to TRUE, and exported a part as DSTV, some holes were not exported because another bolted part had holes in the same location. This issue has now been fixed.
Note that you should not use this advanced option in any new models. Instead, use the No hole option for Special hole type in the Bolt properties.

Where Tekla Structures 2021 SP11 or SP12 and Tekla Structural Designer 2022 (any service pack) were installed on the same computer and the direct link was used for importing or exporting, the import or export process failed.
This issue has now been fixed in this service pack for Tekla Structures. There is no need to install a different service pack for Tekla Structural Designer 2022.

IFC4 export: Surface treatment was exported out of the IfcProject hierarchy. This issue has now been fixed.

IFC2x3 export: When you minimize the Property set definitions dialog box, it is now visible on the taskbar, and you no longer lose the dialog box. You can also locate the Property set definitions dialog box by using the Alt+Tab keyboard shortcut.

Previously, column headers were not positioned correctly in tables that were filled vertically from top to bottom and aligned to the right. This has now been fixed.

Template Editor: Sometimes, when you moved multiple objects horizontally using the Move Object dialog box, the objects also moved vertically. This issue has now been fixed.

Tekla Structures stopped responding when a drawing template had an invalid ValueField formula that referenced itself with the GetFieldFormula function. This issue has now been fixed.

Previously, using the template attribute ASSEMBLY_POSITION_CODE for a part outside the grid could sometimes cause a Tekla Structures application error. This issue has now been fixed.

Earlier, when using a bolt hole mark with a template attribute in single-part drawing views, the main part hole information was always shown even though the secondary part had a different hole. This issue has now been fixed.

Part marks in drawings: New empty marks are now positioned correctly again.

When you create a mark or an associative note manually, and the content in the properties is not defined for the object type you have selected in the drawing, a mark or a note with a text element set to "Content undefined" is created, and you can then double-click the mark or note and modify the content and properties in the properties dialog box.
Earlier, manually created marks and associative notes that did not have content defined in the properties used to be empty and invisible. 

Previously, snapping to intersection points of a radial grid in drawings did not work. This has now been fixed.

Manually hidden objects in drawings no longer hide content behind the text of the hidden object.

Layout editor: Previously, after clicking Close layout editor on the Layout editor ribbon, the Save button in the Save layout dialog box became inactive and you could not save the modified layout. This issue has now been fixed.

Previously, Tekla Model Sharing features became inactive after write out or read in when using the Drafter license. This has now been fixed.

In the UK environment, the calculated weights of the profiles UB533x165x66 and UB533x165x75 were incorrect due to the cross sectional area being incorrect in the profile catalog. This issue has now been fixed.

When changes in the physical model are considered for an analysis model or analysis part (Automatic update set to Yes - Physical model changes are considered), changing the rotation for a physical part now updates the corresponding analysis object.

Tekla Structures 2021 is only compatible with Tekla Structural Designer 2021 or 2022 (all service packs). Previously, if Tekla Structural Designer 2023 was also installed, the direct Import and Export commands tried to use the latest version and then failed without a specific message.
This issue has now been fixed so that Tekla Structures 2021 will use the correct version for direct import and export. For example:

• If Tekla Structural Designer 2021 and 2022 and 2023 are installed, the direct links will use Tekla Structural Designer 2022.
• If Tekla Structural Designer 2021 and 2023 are installed, the direct links will use Tekla Structural Designer 2021.
• If only Tekla Structural Designer 2023 is installed, the direct links will warn the user that there is no compatible version of Tekla Structural Designer.

Please note that Tekla Structures 2023 is only compatible with Tekla Structural Designer 2023 (all service packs).

DSTV/NC export: Previously, the blind hole depth was not exported to the NC file when the bolt had a negative cut length. This issue has now been fixed.

Export Unitechnik (79): You can now select the embeds to export by specifying a filter in Embed filter on the Embeds tab.

Export ELiPLAN file (68): Previously, the data conversion file mapping did not work for profiles that had parentheses in the profile name. This issue has now been fixed.

Export ELiPLAN file (68): Previously, when an exported element had skewed cuts at the start or at the end, the exported values were not correct. This issue has now been fixed.