2021 SP6: 새로운 기능, 개선 사항 및 주요 수정 사항

Tekla Structures
2021
Tekla Structures

2021 SP6: 새로운 기능, 개선 사항 및 주요 수정 사항

최신 Tekla Structures 서비스 팩 및 업데이트된 환경 설치 프로그램은 Tekla Downloads에서 이용 가능합니다.

온라인 라이선스: 허가된 라이선스 유지를 위한 새로운 고급 옵션

새로운 고급 옵션 XS_DEFAULT_KEEP_ONLINE_LICENSE_CHECKBOX는 종료 확인 메시지 상자에서 이 장치에 허가된 이 라이선스 유지의 기본값을 설정하기 위해 도입되었습니다. 이 고급 옵션은 초기화(.ini) 파일에서 설정해야 합니다. 기본값은 TRUE이며 허가된 라이선스를 유지합니다. 이 고급 옵션을 설정하지 않거나 TRUE로 설정하면 명명된 라이선스를 사용하거나 이전 Tekla Structures 세션에서 허가된 라이선스를 유지하도록 선택한 경우에 해당 확인란이 선택됩니다. 이 고급 옵션을 FALSE로 설정하면 이 장치에 허가된 이 라이선스 유지 확인란은 절대 기본적으로 선택되지 않습니다.

TTSD-45097

TDX 포인트 클라우드 파일 형식 신규 지원

이제 TDX 포인트 클라우드 파일 형식이 지원됩니다. TDX는 Trimble의 독자적인 간결한 포인트 클라우드 형식입니다. 현장에서 Trimble FieldLink 또는 Trimble Perspective로, 혹은 사무실에서 Trimble RealWorks 또는 Trimble Business Center로 인필드 등록, 정제 및 모델 좌표 참조 후 스캔 데이터가 정확한 위치에 Tekla Structures로 직접 로드될 수 있습니다.

TTSD-45311

레벨 마크 추가 시 스냅

도면에 레벨 마크 추가 시, 선택된 스냅 스위치에 따라 스냅이 적용됩니다.

TTSD-24182

수정

결함 번호 개발 영역 설명
TSAC-1948 Concrete components

Floor layout: Geometry calculation has been improved in situations when openings are collinear but not overlapping to any edge at the seam.

TSAC-4103 Concrete components

Wall layout connector has been improved. Now the connector's L corners work for wall layouts with different top and bottom heights. The corner item's top and bottom are matching only where the walls connect.

TSAC-5099 Concrete components

Floor layout: Previously, holes and cuts that should have been created automatically were not created if the cutting part was located in the negative offset area, that is, outside the input polygon. This has now been fixed.
 

TSAC-5120 Concrete components

Hole generation (32): Rebar sets in a part will now be automatically cut.

TSAC-5737 Concrete components

Concrete beam-beam (112): You can now use the Create washers symmetrically setting on the Anchors tab to define whether the washers on the anchors are created symmetrically (mirrored) to the washers on the anchors at the opposite beam side.

TSAC-5753 Concrete components

Embedded Anchors (8): The Avoid reinforcement setting on the Placement tab now detects all rebars in collision with each created anchor and moves the anchors out of the collision with a cover thickness. Also, the detection works in the range of the anchor bounding box + the desired cover thickness.
 

TSAC-5808 Concrete components

Floor layout: Previously, when creating automatic cut-outs for I-shaped columns, only a small cut was created at one flange if the I shape web was not touching the slab. This has now been fixed.

TSAC-6072 Concrete components

Wall layout connector: Previously, the corner part was sometimes not created because the part profile was not correct. This has now been fixed.

TSAC-6073 Concrete components

Floor layout: The Floor layout dialog box now opens correctly when you specify that there are no UDAs listed on the User defined tab. Previously, you had to have at least one UDA on the User defined tab.

TSAC-5466 Steel components

Base plate (1042): Previously, the distances from the flange of the main part to the edge of the base plate were swapped in the component. This has now been fixed.

TSAC-5572 Steel components

Round tube (23): Previously, the fitting of the secondary part was created incorrectly in some orientations of the secondary part. This has now been fixed.

TSAC-5602 Steel components

Splice plate 2 (62): Previously, the primary web bolts assembly was not applied correctly. This has now been fixed.

TSAC-6057 Steel components

Stiffened end plate (27), Partial stiffened end plate (65): Previously, bolt edge distances were incorrectly applied in the component. This has now been fixed.

TSAC-6069 Steel components

Clip angle (141): Previously, extra length was not correctly applied for all bolts. This has now been fixed.

TSAC-6097 Steel components

Full depth (184): Previously, some notch cuts were created with infinite length. This has now been fixed.

TTSD-48084 Steel components

Previously, in some rare cases, when you modified the properties of a component and had selected the ignore other types option, certain properties of some other components were still modified. This has now been fixed.
 

EPM-4558 Import, export, interoperability

Export to Tekla EPM: CNC files that are copied during the export are now preserved in the same directory structure they were copied from.

 

EPM-5052 Import, export, interoperability

Export to Tekla EPM: Exporting to Tekla EPM from an assembly selection in the Tekla Structures model is now supported.

EPM-5537 Import, export, interoperability

Export to Tekla EPM: The Standard settings are now reloaded when the window is closed and reopened.

EPM-5692 Import, export, interoperability

Export to Tekla EPM: A field has been added to the XML file exported from Tekla Structures, telling what version of the plugin was used to create the file.

EPM-5717 Import, export, interoperability

Export to Tekla EPM: If no settings file is found when you run the plug-in, one is automatically created with default options.

EPM-5718 Import, export, interoperability

Export to Tekla EPM: The Save button did not save the current settings correctly. This has now been fixed.

EPM-5744 Import, export, interoperability

Export to Tekla EPM: PROJECT.NUMBER can now be included in advanced settings to print drawings, and will be found when those drawings are copied into the zip file exported to Tekla EPM.

TTSD-44018 Import, export, interoperability

IFC2x3 export: Previously, additional property sets did not work on reinforcing meshes. This issue has now been fixed.

TTSD-45311 Import, export, interoperability

Point clouds: The .tdx point cloud file format is now supported.

TTSD-46056 Import, export, interoperability

IFC4 export: It is now faster to export IFC files containing property sets reporting hierarchical information. For example, mapping a property set to report "POUR_UNIT.NAME" (the name of the pour unit that a rebar belongs to) would slow down the export tremendously. This has now been fixed.

TTSD-46672 Import, export, interoperability

Trimble Connect: An error message is now displayed if the model upload to Trimble Connect fails.

TTSD-47152 Import, export, interoperability

IFC2x3 export: Weld coloring has been improved when you use current view colors.

TTSD-47266 Import, export, interoperability

IFC export: The IFC export is using translation strings from all folders mentioned for the XS_MESSAGES_PATH advanced option.

TTSD-47437 Import, export, interoperability

Reference models: Inserting an IFC model as a reference model was slow in a certain use case. This issue has now been fixed.

TTSD-47531 Import, export, interoperability

IFC2x3 export: Bolt and weld colors are now correct when you export with or without current view colors, or using user-defined colors, or colors defined by class.

TTSD-48082 Import, export, interoperability

Previously, you could not export IFC4 property sets for location breakdown structure properties (for example, LOCATION_BREAKDOWN_STRUCTURE.LBS_FLOOR). This issue has now been fixed.

TPLED-213 Templates and reports

The Valuefield did not give a correct result when the formula had a CopyField() function and used directly or by a reference the ROW_IN_PAGE attribute. This issue has now been fixed.

TPLED-217 Templates and reports

Template Editor: Circles in an imported DWG image sometimes had an incorrect color, and filled polylines could be missing. This has now been fixed.

TSAC-5394 Drawings

Rebar pull-out picture and marking: The hook representation has been improved, and 135 and 180 degree hooks are now correctly visualized.

TSAC-5634 Drawings

Rebar pull-out picture and marking: You can now define the pull-out picture scale on the Rebar tab. In Type, select Auto or Custom. If you selected Custom, type the needed Scale value.

TSAC-5905 Drawings

Automatic dimensioning with the Shape dimensions dimensioning type could hang Tekla Structures in some cases when round geometry was dimensioned. This has now been fixed.

TSAC-5916 Drawings

Rebar pull-out picture and marking: The rotation of the rebar sets has been improved. Previously, the rotation of the pull-out was not always matching the bar in the drawing.

TSAC-6013 Drawings

Drawing dimensioning performance has been significantly improved when you use the Filter dimensions method to dimension reinforcement.

TTSD-26401 Drawings

Hidden rebar lines that were not visible in the drawing mode were sometimes visible in printed output and snapshots. This has now been fixed.

TTSD-41841 Drawings

PDF reports with images on each page quickly became very large the more pages there were. This issue has now been fixed.

TTSD-44484 Drawings

Document manager: Drawings with container views now work correctly with the Select objects in the model  for selected drawings command. 

Image
Select objects in model
TTSD-45025 Drawings

Layout editor: Layout editor now allows you to edit the size width and height by selecting the appropriate cell and pressing the Enter key.

TTSD-45477 Drawings

When using the on/off button in the old drawing view properties dialog boxes, not all the check boxes in the dialog box changed their state. This issue has now been fixed.

Image
On/off button

 

TTSD-46058 Drawings

Pressing the Tab key on the keyboard for changing the current snapping location works again in drawings.

TTSD-46577 Drawings

Recess symbols now work correctly in drawings also when the part representation is Base box.

TTSD-47191 Drawings

Printing: Previously, printing would fail if there were any errors in the TeklaStrutures.lin line type file, now any unrecognized lines will be ignored. Unrecognized line styles will be logged and drawn with a solid line, matching the drawing editor.

TTSD-47421 Drawings

Reading dimensioning rule files from relative folders using advanced options XS_FIRM and XS_PROJECT is now possible. For example, XS_FIRM=".\ts" can be used to read files from  the 'ts' folder inside the model folder.

TTSD-47570 Drawings

Printing: Symbols located in paths containing non-Latin characters did not always appear in printouts. This issue has now been fixed.

TTSD-47752 Drawings

Earlier, all reference models were handled when creating single-part drawings, which caused a performance issue. This has now been fixed.

TTSD-47839 Drawings

In the old Single-part drawing properties dialog box pressing the on/off button did not change the state of the Weld mark check box. This issue has now been fixed.

TTSD-47853 Drawings

Layout editor: The template width was not calculated correctly for a template with a variable number of columns, which caused the anchoring point to not adjust correctly. This has now been fixed.

TTSD-47863 Drawings

A staircase component has in one occasion caused invalid geometry to a part, causing the drawing containing the part to freeze during the drawing opening. This has now been prevented.

TTSD-48164 Drawings

Document Manager: Document Manager was not updated to reflect the file changes in the watched subfolders. This issue has now been fixed.

TTSD-48613 Drawings

Dimension associativity: Dimension associativity rules for weld preparation cuts now show a correct label instead of an empty text.

TTSD-48711 Drawings

Printing: Scaled hatch pattern lines with a delta Y of less than 0.01 mm caused hatching to fail to prevent excessive processing and hanging, which caused asserts when printing. This has now been fixed.

TTSD-46286, TTSD-48108 Modeling

Previously, splitting a lofted plate or a lofted slab using the Split command did not work. This has now been fixed.

TTSD-46883 Modeling

Previously, Tekla Structures handles were difficult to select. This has now been fixed, and the handle selection is easier.

TTSD-47169 Modeling

The log file for usage data, UserFeedbackLog.txt, is now stored in the Logs folder under the path defined with XSUSERDATADIR in teklastructures.ini file.

TTSD-47462 Modeling

Previously, modifying concrete panels could sometimes cause Tekla Structures to close suddenly. This has now been fixed.

TTSD-47792, TTSD-48445 Modeling

Previously, in the US Imperial environment, the maximum possible supported precision for bolt size was 1/16. This resulted in incorrect bolts being added to the model from the bolt catalog. Now the precision has been increased to 1/128.

TTSD-47798 Modeling

Previously, when using the Split command, the splitting of a part was not accurate if the picked point for splitting was outside the part. Now, dimensions and a preview is shown when a part is split, even from outside the part itself. For polybeams only dimensions are shown, not the preview.

TTSD-47983 Modeling

Previously, it was not possible to save or load surface treatment pattern properties or user-defined attributes in the property pane. This issue has now been fixed.

TTSD-48371 Modeling

Clash check manager now detects clashes between reference model objects and objects inside components.
 

TTSD-48510 Modeling

Sometimes when loading bolt properties from a file in the US metric environment, the bolt size was not set correctly in the property pane. This issue has now been fixed.

TTSD-48520 Modeling

Previously, deleting many selected objects was extremely slow. The performance problem causing this has now been fixed.

TTSD-48546 Modeling

Lofted plate geometry for antimaterial and addmaterial was removed during a database repair, if XS_DELETE_UNNECESSARY_INT_ARRAYS was set to TRUE. This led to corrupted antimaterial/addmaterial and to a failed solid of the part influenced by the antimaterial/addmaterial. This issue has now been fixed. Additionally, these errors are now reported when models with already removed geometry are being diagnosed.
 

TTSD-48751 Modeling

Previously, when using the Open properties command for grid lines on the contextual toolbar, both the old Grid line properties dialog box as well as the property pane was shown. This has now been fixed.

TTSD-47254 Installation

Previously, when trying to install an environment, there could be an error in .tsep file installation if the user's computer was configured to use a virtual desktop. The folder path to the virtual desktop could not be accessed and the .tsep package validation did not succeed. This issue has now been fixed and the installation now continues. Note that .tsep shortcuts cannot be created on the virtual desktop. If the .tsep requires a shortcut, instructions about adding the shortcut manually will be added to the installation log.

TTSD-48024 Tools and components

Previously, the Applications & components catalog could stop responding to mouse clicks if you pressed the Home or End key while using the catalog. You could not select any groups or items in the catalog, for example. This has now been fixed.

TSAC-6009 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, in some cases, the line attribute override from surface object applied into an incorrect concrete edge when the object faces were complex. This issue has now been fixed.

TSAC-6026 Import, export, interoperability (concrete)

Export EliPLAN file (68): The data conversion file can now be read from the XS_FIRM and XS_PROJECT folders.
Export Unitechnik (79): The special export assembly file names and reinforcement definition file can now be read from the XS_FIRM and XS_PROJECT folders.

TSAC-6027 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, mesh turned to pallet plane failed with some mesh within stair elements. Also, when you exported multiple cast units with surface objects designated as pallet base, the elements were exported incorrectly. This issue has now been fixed.

TSAC-6065 Import, export, interoperability (concrete)

Export Unitechnik (79): You can now export iron projection data using the new Iron projection setting on the SLABDATE block data specification tab. The values are automatically determined from reinforcement length that extends outside the element. The Special formwork for embed setting has been renamed to Special formwork for object, and now this setting also works for reinforcement specified by class or by name.

TSAC-6094 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Previously, weep holes were exported incorrectly when hollowcore was cut by its longer side. This issue has now been fixed.

도움이 되었습니까?
이전
다음