Railings (S77): Previously, when the horizontal length of the closure was specified as 0.0, the vertical rails (pickets) were not created correctly. This issue has now been fixed.

Spiral stair (S68): Previously, steps were created with an incorrect geometry when a small outer radius was specified for the steps. This issue has now been fixed.

Stanchions - Railings - Kick plates (S86): Previously, exploding the component was not working correctly. This issue has now been fixed.

Tube gusset (20): Previously, weld 2 was not created correctly. This issue has now been fixed. In addition, weld 9 has been added as a weld between the connection plates and the middle end plate.

Railings (S77): Previously, when using the Other rail to stanchion fitting options, the part cut was created in an incorrect position for some stanchions. This issue has now been fixed.
 

Tube crossing (22): Previously, weld 2 was not created correctly. This issue has now been fixed. In addition, weld 3 has been added as weld between the connection plates and the middle end plate.

Gusset+ T: Previously, the connection did not work in the Japanese environment when the brace connection type was set to Built up. This issue has now been fixed.

Shear plate simple (146): Previously, when the beam flange cut was set to square and a notch was also created, the depth of the square flange cut was not the same as the notch cut depth. This issue has now been fixed.

Shear plate simple (146): Previously, when the secondary part was skewed and the web was cut square, the bolt edge distance was not correct. This issue has now been fixed.

Joist to beam, type 1 (160): Previously, a full depth stabilizer plate was not created correctly in some situations. This issue has now been fixed.

JP Full depth special (185): Previously, the shear tab was created in an incorrect position in some situations. This issue has now been fixed.

Welded gusset (10): Previously, the cut in the bracing around the gusset was created with incorrect dimensions in some situations. This issue has now been fixed.

Stairs (S71): Previously, the steps were clashing with the stringers in some situations. This issue has now been fixed.

JP Floor beam gusset (11): Previously, bolt cut length was incorrectly calculated in some situations. This issue has now been fixed.

Cold rolled overlap (1): Previously, the component did not work correctly for PEB members with multiple depths. This issue has now been fixed.

Tube gusset (20): The default values of stiffener chamfer sizes are now taken from the main part profile radius.

Stiffened end plate (27): Previously, when the horizontal offset of bolts was specified, the end plate was moved incorrectly. This issue has now been fixed.

IFC2x3 export: Objects with multiple fittings were sometimes exported incorrectly. This issue has now been fixed.

Import from Tekla Structural Designer: While importing a model from Tekla Structural Designer to Tekla Structures, there was an issue with the Z grid labels in Tekla Structures with respect to the levels in Tekla Structural Designer. This issue has now been addressed and fixed.

IFC2x3 export: Now, double nuts for bolts with cup heads are exported with a 30-degree rotation relative to each other, improving visualization.

Previously, curved dimensions in 2D Library details did not work correctly. This issue has now been fixed.

Earlier, when creating unfolded single-part drawings for lofted plates that had oblique cylindrical geometry, bending lines were missing. This issue has now been fixed.

Document manager: The Select and show only drawings containing parts currently selected in the model button is now enabled also when a drawing is open. Earlier, this button was disabled when a drawing was open.

Reference models: Sometimes, some parts of reference models were using fill when they should not have been. This issue has now been fixed.

Earlier, there was a rare situation when creating a polyline caused Tekla Structures to exit unexpectedly. This issue has now been fixed.

Fabrication drawings: There were some problems in the user interface functionality when you tried to use Smart create for creating rebar assembly drawings. This has now been fixed.

Printing to PDF: Earlier, due to Windows 11 24H2 update, the JPG images were shown incorrectly when printed to PDF. This issue has now been fixed.

Tekla Model Sharing: When you read in, Tekla Structures updates custom components which are outdated compared to their definitions. There may be incorrectly defined custom components which result in their instances being always updated, leading to unexpected change notifications. This has now been prevented, and the components which have incorrect definitions are not updated.

Previously, the dynamic preview of the Move or Copy command caused Tekla Structures to stop working when using the command for reinforcement containing a very large number of vertices, for example, a braced girder. This issue has now been fixed.

Previously, the Switch user button did not work. Now when a user clicks Switch user, the user is signed out of Tekla Structures. After restarting Tekla Structures, a different user can sign in.

Offline mode error: The offline mode window kept popping up while working online and, in most cases, clicking Try reconnecting now did not work. This issue has now been fixed.

The stability of the Compare commands has been improved in situations where part solids could not be created.

Export to Tekla PowerFab: The model weight is now exported with the bill of materials.

Export ELiPLAN file (68): Previously, round-shaped edge contour corners were exported as bounding boxes. This has now been fixed and round-shaped edge contour corners are correctly exported as lines.

Export Unitechnik (79): When exporting meshes into individual files using the Split meshes to individual files setting on the Main tab, a running number is now automatically added to the file name.