Engineering library update - April 2022

Tekla Tedds
2022
Tekla Tedds Tekla Tedds for Word

Engineering library update - April 2022

The latest Tekla Tedds engineering library update is available in Tekla Downloads.

All Regions

Updates

Library Access System
TEDDS-6523 Fixed all system set files (.las) which were missing from the original 2022 release.

American Design

Updates

Wood member design (NDS)
TEDDS-6543

Adjusted minor axis properties of West Fraser LVL in datalist.

TEDDS-6443

UI speed improvements for _SectionLock = 1.

TEDDS-6442

Adjusted calculation call to eliminate unnecessary runs.

TEDDS-6421

Disable bearing check inputs when design reactions are zero.

TEDDS-6285

Summary table option now enabled even when users have selected no output.

TEDDS-6284

Overall design summary in preview window.

TEDDS-6265

Adjusted way sections are referenced within the ui.

TEDDS-6264

Updated layout of ui.

TEDDS-6263

Added section name variable.

TEDDS-6205

Summary table for all design sections now shown at top of output.

TEDDS-6201

Identify single section inputs in Tedds UI

Australian Design

Updates

Pad footing analysis & design (AS3600)
TEDDS-4767 Corrected undefined variable error, _OnlyMinShearReinfReqd.

British Design

Updates

Concrete industrial ground floor slab design (TR34)
TEDDS-2073 Fixed pass/fail statement in the user interface when a negative capacity is calculated. This is now shown as beyond scope.
TEDDS-3581 Enhanced to include dimensions for the validity of the load type location, on the edge distance control description in the user interface.
TEDDS-6455 Fixed the cracked to uncracked ratio check not appearing in the output.

Canadian Design

Updates

Anchor bolt design (CSA-A23.3)
TEDDS-6437 Amended factor for effective cross-sectional area of anchor.

Eurocode Design

Product Bulletin April 2022 (PBT-2204-2)

Fixed a potentially un-conservative error affecting all calculations which allow steel channel sections to be selected, when the Tedds country setting is Finland, Sweden or Norway and specific UAP or UPN sections are used. For more detailed information please refer to Product bulletin April 2022 (PBT-2204-2).

Product Bulletin April 2022 (PBT-2204-1)

Crane gantry girder design (EN1993) - Fixed a potentially un-conservative error affecting the local stress calculations for underslung cranes. For more detailed information please refer to Product bulletin April 2022 (PBT-2204-1).

Product Bulletin March 2022 (PBT-2203-1)

Foundation analysis & design (EN1992/EN1997) - Fixed a potentially un-conservative error affecting the calculation of the passive resistance used in the sliding check. For more detailed information please refer to Product bulletin March 2022 (PBT-2203-1).

Updates

Foundation analysis & design (EN1992/EN1997)
TEDDS-6303 Corrected calculation of horizontal force angle when negative forces are applied.
Pile analysis (EN1997)
TEDDS-5985 Fixed undefined variable error when selecting circular steel pile.
RC column design (EN1992)
TEDDS-6472 Enhanced to include new option to define the maximum number of iterations performed by the calculation to determine the column capacity.
Steel member design (EN1993)
TEDDS-6398 Bending and axial compression check was being applied to members in tension when using the Singapore national annex.
Steel to concrete simple connection design (EN1993)
TEDDS-6279 Fix bug not allowing rebar weld less than 60mm i=to be inputted.
Timber connection design (EN1995)
TEDDS-6427 Fixed incorrect load utilisation value shown in the ui and summary table for axially loaded fixings.
Timber member design (EN1995)
TEDDS-6443

UI speed improvements for _SectionLock = 1.

TEDDS-6442

Adjusted calculation call to eliminate unnecessary runs.

TEDDS-6434

Enable National Annex options when _SectionLock = 1.

TEDDS-6285

Summary table option now enabled even when users have selected no output.

TEDDS-6284

Overall design summary in preview window.

TEDDS-6265

Adjusted way sections are referenced within the ui.

TEDDS-6264

Updated layout of ui.

TEDDS-6263

Allow design only sections to be selected by name rather than section reference.

TEDDS-6205

Summary table for all design sections now shown at top of output.

TEDDS-6201

Identify single section inputs in ui

Was this helpful?
上一步
下一步