Embedded anchors (008): Previously, in some situations, the Selected part option for anchor placement did not work properly. This issue has now been fixed.

Embedded anchors (008): Previously, in some situations, the component stopped working correctly when deployed on staircases. This issue has now been fixed.

Cold rolled overlap (1): Previously, stay plates were not created when the bottom flange plate was cut using a PEB end plate to the flange connection. This issue has now been fixed.

Two sided end plate (142): Previously, haunch plates were not created correctly when you defined some specific haunch plate dimensions. This issue has now been fixed.

Stiffened end plate (27): Previously, weld 9 was created in an incorrect location in some situations. This issue has now been fixed.

IFC property sets: When creating property sets for the IFC export, you can now select and add also custom properties. Previously, only default attributes were available for selection.

IFC export: Building hierarchy item properties are now available in the Property set definitions dialog.

Previously, some washer type and number properties were not exported with TrimBIM or IFC4. This has now been fixed.

IFC4.3 export: Now, the IFC4.3 export also supports IfcBearing when the Reference view or Design transfer view export type is used.

IFC4 export: Sometimes, the export of custom properties did not work. This issue has been fixed.

Template Editor: When the first row of a table (row with Use Columns selected) could not fit into the page, the page height became incorrect, which disrupted the page layout. This issue has been fixed.

Weld marks: The background settings for weld marks are now correctly applied during drawing creation.

Earlier, in specific cases, changing the properties of rebar dimension marks for rebars in sloped parts could cause changes in dimensions to part edge. This issue has been fixed.

Cloning: Previously, when you cloned general arrangement drawings containing section views, the section views disappeared from the source drawing. This issue has now been fixed. Additionally, the cloning of section views in general arrangement drawings has been improved so that the content of the cloned section views now corresponds to the content of the selected model view.

Reinforcement ticks and tags: The status bar now shows the translated status bar messages. Previously, the status bar showed the untranslated placeholder texts.

Previously, the shared model environment was sometimes incorrectly displayed as Custom instead of a local environment. This issue has been fixed.

With on-premises sharing services, the previously added on-premises servers were not visible in the list of services. This issue has been fixed, and the previously added servers are visible in the list.

An issue was fixed where diagnosing and repairing previously deleted user-defined attribute values instead of converting them to the correct value type. Tekla Structures now first attempts to convert UDAs to the correct value type, and only then deletes any possible mismatched values.

Previously, text in Japanese and some other languages was not displayed correctly in the modeling view. This issue has been fixed.

Previously, when the work plane was set to a location other than the default plane and bolts were created using a part face, the bolts were positioned far from the selected part face. This issue has been fixed.

Previously, when a polybeam with a profile containing at least one very large dimension was created, and a new part view was created, for example, from the face of another object, the unwanted polybeam appeared in the new view. This has been fixed, and the view depth does not display these objects any more.

Building hierarchy: Previously, when filtering the location breakdown structure, using the Building property did not work if the objects were under a building section. This issue has been fixed.

Previously, Tekla Structures sometimes closed unexpectedly if a connection inserted a weld that had invalid profile information. This issue has been fixed.

Building hierarchy: When using the Select assigned objects command, the objects assigned to a building hierarchy element are now shown as selected objects in the property pane.

Live Collaboration: When sharing clip planes and clip boxes in Live Collaboration sessions, the base point is now taken into consideration.

An issue with listing folder contents in Trimble Connector for certain projects has been fixed.

Copying custom object UDA values in the property pane works now more reliably.

Live Collaboration: When sharing markups in Live Collaboration sessions, the base point is now taken into consideration.

Autosaving: Previously, it was not possible to open an autosaved model when using Spanish as the Tekla Structures language. This issue has now been fixed.

Trimble Visualizer has been updated to a newer version.

Tekla Launcher: The previous version of Tekla Launcher has now been replaced with a standalone version of Tekla Launcher. This allows you to open models with the relevant Tekla Structures version based on the model information. 

Support tool: You can now select individual files via a checkbox on the left side of the file list, similar to file groups. The file group selection boxes now update automatically to show if all, some, or none of the files within that group are selected.

Support tool: Previously, any extra files you uploaded were not assigned to a file group. These files are now grouped under Manually added files.

Support tool: Files in the Contact support dialog are now automatically sorted in ascending alphabetical order by default, which is indicated by the active arrow icon next to the File group column header.

Support tool: A spinner icon is now displayed while files are being packaged for the support case.

Support tool: The previously incorrect Hungarian translation for the All option in the file selection list has been replaced with Összes.

Support tool: File groups are now sorted alphabetically, with the exception of Other files and Manually added files, which always appear at the end of the list, or at the beginning if the sort order is descending.

Export Unitechnik (79): Previously, incorrect data was exported for reinforcement that was exported as embed. This issue has been fixed.