Braced girder (88): On the Parts tab, you can now specify the axis direction for the Model work plane position: Model XY, Model YZ, or Model ZX.

Concrete console (110): When the anchor was created as a reinforcing bar, the option to add it to the beam did not work, the anchor was always added to the column. This issue has now been fixed.

Concrete console (110): The Name property of Dowel defined on the Socket tab can now have a maximum of 62 characters. Previously, the maximum number of characters was 20.
 

Reinforced concrete stairs (95): Previously, in some situations, stair part IDs could change when modifying the component. This caused connections with other components to break. This issue has now been fixed.

Concrete console (110): Previously, the neoprene connection sometimes connected the wrong parts. This issue has now been fixed.

Embedded anchors (008): On the Picture tab, you can now select Half sphere as the shape of the cutout around the anchors.

Automated reinforcement layout - double tee beam (51): The leg length of stem stirrups is now set correctly as defined in the component dialog box.

Haunch (40): Previously, weld number 4 was created in an incorrect position in some cases. This issue has now been fixed.

Bolted gusset (11), Tube gusset (20), Gusseted cross (62), Bolted gusset (196): Previously, the welds between the stiffeners and the main part were only created to the main part web. This has now been improved. The welds are also created to the main part flanges.

Full depth (184): Previously, the horizontal bolt edge distance was not applied correctly. This issue has now been fixed.

Welded to top flange S (149), Full depth S (185), Column with stiffeners (186), Column with stiffeners (188): Previously, notch sizes were not correctly rounded when the secondary part was sloped. This issue has now been fixed.

Gusset+ T: Previously, the connection was not always created in situations where the secondary part had a fitting at the opposite end. This issue has now been fixed.

Gusset+ T: Previously, the creation of special bolt holes depended on whether the gusset plate had been set to be above or below the T profile. This issue has now been fixed. Special bolt holes are created as defined on the Bolts tab regardless of the gusset plate position.

Tube gusset (20): Previously, certain distance values between the main part and the first selected brace could cause the gusset plate to have an incorrect shape. This issue has now been fixed.

Stub connection (119): Previously, the assembly part numbering prefix and start number were incorrectly set for all parts. This issue has now been fixed. The correct assembly part numbering prefix and start number are now taken from Settings > Options > Components > Part start numbers.

Wraparound gusset cross (60): Previously, connection plates between the gusset plate and the main or secondary part were placed in an incorrect position in some situations. This issue has now been fixed.

No paint area: Previously, the component was not created in some situations when you tried to create it in the model. This issue has now been fixed.

U.S. Base plate (1047): Previously, the holes in the cast plate were created incorrectly when the base plate was offset. This issue has now been fixed.
 

Joist to beam, type 1 (160): Previously, bearing plate material was not correctly applied. This issue has now been fixed.

Kingspan Horizontal cladding support column (33): Cleat orientation is now correct when using an L14570 section below an eaves beam.

Kingspan Horizontal cladding support column (33): Previously, L145V to eaves beam at column had the top cleat facing the wrong direction. This issue has now been fixed. The component has also been limited to standard sheeting lines (181, 211, 241, and 271).

Clip angle (141), Two sided clip angle (143): Previously, notch sizes were not correctly rounded when the secondary part was sloped. This issue has now been fixed.

End plate (144), Two sided end plate (142): Previously, notch sizes were not correctly rounded when the secondary part was sloped. This issue has now been fixed. 

Shear plate simple (146), Welded to top flange (147), Full depth (184): Previously, notch sizes were not correctly rounded when the secondary part was sloped. This issue has now been fixed.

U.S. Base plate (1047): Previously, when you defined the leveling plate hole diameter, double bolts were created. This issue has now been fixed.

No paint area: If you modify a successful instance of the No paint area component in a way that would cause an error or that would not create the surface treatment, the previously created surface treatments are now removed as they should. In addition, a warning message is shown on the status bar, as previously. 

Shear plate to tube column (47): Previously, secondary part notches were not created in all situations. This issue has now been fixed.

Stiffened shear plate (17): Previously, the width of the shear tab was not calculated correctly. This issue has now been fixed.

Reference models: IFC import plug-in has been updated to version 6.48.

IFC export: The roundings for part cuts are now visible when the export type is Steel fabrication view.

Trimble Connector: When you were uploading a model to Trimble Connect, the  upload time shown in Trimble Connector was UTC. This issue has now been fixed, and Trimble Connector shows the local time.

IFC export: An invalid solid of a part could cause an application error when certain template properties were inquired. This issue has now fixed.

Template Editor: Color overrides did not work when a row rule had IsFirst, IsLast, PreviousValue, NextValue, or CopyField in any of the rows in the template. This issue has now been fixed.

Rebar pull-out picture and marking: In some cases, the pull-out picture rotation was incorrect. This has now been fixed.

Drawing content manager: The Drawing content manager performance has been improved significantly, leading to faster loading times, such as for GA drawing content.

View-specific dimensioning: Shape dimensions was in some cases creating extra incorrect dimension points in drawing update. This issue has now been fixed.

Earlier, when you filtered an object away from a drawing view and then disabled the filter, hidden lines did not appear if XS_ENABLE_OVERLAPPING_CUT_LINE_REMOVAL was activated. This issue has now been fixed.

Earlier, when you had set XS_USE_EXISTING_SINGLE_PART_DRAWINGS​_​IN_​ASSEMBLY_​DRAWINGS to TRUE, section views created from single part views affected the bill of materials and layout content in assembly drawings. This has now been fixed.

When rotating drawing templates, an embedded logo or symbol would not rotate together with the rest of the template. This issue has now been fixed.

Document manager: Locking a drawing no longer changes the issuing date of the drawing.

Earlier, when you resized a drawing view so that first a part disappeared and then appeared again, hidden lines disappeared. This issue has now been fixed. 

Earlier, inquiring the hole type and hole attributes in a drawing might lead to incorrect results in assembly drawings. This issue has now been fixed.

When editing a drawing text in the property pane, you can no longer use the Tab key to add horizontal tabulation in the text field. It used to be possible to add horizontal tabulation with the Tab key, but the result in the drawing was incorrect. 

Sometimes a circular reinforcing bar was incorrectly represented by two circular arcs in Rebar shape manager. This issue has now been fixed.

An issue has been fixed to ensure that the geometry presented to Rebar shape manager for a circular overlapping rebar set bar is planar, instead of spiralling. This issue was preventing shape recognition in Rebar shape manager from identifying the correct shape for the bar.

In Rebar shape manager, circular arcs are now combined for any circular overlapping bars so they can now have an angle of over 360 degrees.

Surface objects and also rebar sets with leg surfaces now adapt to small tessellation changes in solid geometry. Tessellation might change when opening a model with a newer version of Tekla Structures, or after changing advanced options such as XS_POLYBEAM_CHORD_TOLERANCE.

Previously, the default cast unit or assembly UDA values were not shown in the property pane. This has now been fixed.

Now, when you click the Activate trial in browser button, a new dialog box opens. It gives you instructions to activate a license in a browser and then proceed to license selection. If a license is found, the Tekla Structures - Start window is shown. If no license is found, the Tekla Structures - Setup window is shown. If you click X, Tekla Structures closes.

Rebar sets: Rebar GUIDs are now shown in the numbering history log in case there are overlapping numbering series for rebar sets.

Previously, if you closed Tekla Structures so that some side pane windows were floating and not attached to the right, left or bottom of the screen, and re-opened Tekla Structures, the side pane windows were shown on top of the start screen. This has now been fixed, and the floating side pane windows are shown only after you have selected a model.

Earlier in very seldom cases, when you were dragging a floating side pane and while dragging on the Applications & components pane, Tekla Structures stopped responding. This issue has now been fixed.