2021 SP11: Mejoras y correcciones importantes

Tekla Structures
2021
Tekla Structures

2021 SP11: Mejoras y correcciones importantes

En Tekla Downloads están disponibles la última versión de servicio de Tekla Structures y los instaladores de entorno actualizados.

Correcciones

Número de defecto Área de desarrollo Descripción
TSAC-6591 Concrete components

Rectangular column reinforcement (83): Side bars 1 now have the correct bending radius.

TSAC-6890 Concrete components

Embedded anchors (008): The Up direction option Top in form face is now by default the part front face when the Top in form face UDA is set to Default. Previously, the Up direction was set to Auto and Tekla Structures displayed a message that the top-in-form face was not set.

TSAC-6897 Concrete components

Concrete console (110): Previously, rebar sets could be copied from the input part when you made any changes to the component. This issue has now been fixed.

TSAC-6900 Concrete components

Mesh bars by area: When applying side distances for rebars, the same shape area is now always reinforced in the same manner, regardless of the polygon settings.

TSAC-6916 Concrete components

Sandwich wall window: Duplicate cut parts are not created in the top detail anymore.
 

TSAC-6935 Concrete components

Corbel reinforcement (81): For double corbels, when the Follow shape setting was set to horizontal, the main bar creation started at the wrong height. This issue has now been fixed.

TSAC-5797 Steel components

Wall rails (1): The top bracket is not duplicated anymore when using a component to create a bracket.

TSAC-6648 Steel components

Previously, when placing surface treatment attributes and the product_finishes.dat file in the XS_FIRM folder, the No paint area component did not load the surface treatment subtype correctly. This issue has now been fixed.

TSAC-6791 Steel components

Joining plates (14): Previously, welds between the stiffeners and the main or secondary part were not created. This issue has now been fixed.

TSAC-6824 Steel components

Welded to top flange (147): Previously, welds number 8 and 9 were not created at all. This issue has now been fixed.

TSAC-6892 Steel components

No paint area: Previously, when you loaded a surface treatment attribute file in the No paint area tool, the depth offset was not displayed correctly in the US imperial environment. This issue has now been fixed.

TSAC-6938 Steel components

Column with stiffeners (188): Previously, an incorrect gap was created between the shear tab and the main part when doubler plates were created. This issue has now been fixed.

TSAC-6941 Steel components

Bolted gusset (11), Tube gusset (20), Gusseted cross (62), Bolted gusset (196): Previously, one of the gusset chamfers was not created in the correct position. This issue has now been fixed.

TSAC-6968 Steel components

CMF Cold rolled cleat (101): The dimensioning of the bolted (non-riveted) window trimmer cleat was fixed.

TSAC-6970 Steel components

CMF Mezzanine floor connection (149) is now available in the Applications & components catalog

TSAC-6971 Steel components

UltraZED PCR - column (61): Previously, changing the profile in the component dialog box had no effect. This issue has now been fixed.

TSAC-6973 Steel components

Column splice (132): Previously, when using angle cleats and division plates, some bolts were not created correctly. This issue has now been fixed.

TSAC-7012 Steel components

Tube crossing (22): Previously, end plates were placed incorrectly when the secondary part was sloped. This issue has now been fixed.

TSAC-7023 Steel components

Ayrshire Cold rolled sleeved (119): Previously, when switching between a standard sleeve and a firewall condition, the component was not created. This issue has now been fixed.

TSAC-7032 Steel components

Wraparound gusset (60): Previously, weld #1 was changed from workshop weld to site weld in some cases. This issue has now been fixed.
 

TSAC-7051 Steel components

Kingspan File transfer (18): Previously, the CAM data for the counterformed holes ignored the bolt direction and always put them as Counterformed in. This issue has now been fixed.

TSAC-7062 Steel components

Kingspan Standard tie bay (10): Previously, rails drawn in the same direction affected the direction of the counterform. This issue has now been fixed.

TSAC-7064 Steel components

Ayrshire File transfer (92): Swage LC cleats have been added to the Ayrshire File transfer.

TSAC-7088 Steel components

CMF Cold rolled sleeved (120): Previously, a single-sided stay removed the bolt from the opposite side. This issue has now been fixed.

TTSD-52738 Steel components

Previously, when you added manually created stanchions and Railings (77) component to a custom component and used the Default or Use all stanchion selection option, Tekla Structures might have stopped working unexpectedly, depending the content of the custom component. This has now been fixed.

We recommend to use the Use selected option in the case when all selected stanchions are to be used, even though in a well-define case the Default option produces identical results.

TTSD-54626 Steel components

Earlier, when you added End plate connection (144) between a column (main part) and Girder (S94) (secondary part), Tekla Structures stopped working and you had to restart it. This issue has now been fixed. 

TSAC-6860 Import, export, interoperability

Layout manager now supports Export Field Link files (.tflx) to export all layout data in the model to a Trimble Field Link device from version 6.3 onward.

TTSD-26939 Import, export, interoperability

IFC2x3 export: The export consumed excess amount of memory on each export without releasing it. Only reopening Tekla Structures released the memory. This issue has now been fixed, and the export no longer consumes excess amount of memory.

TTSD-48454 Import, export, interoperability

IFC2x3 export: The IFCBUILDINGSTOREYs now have correct GUIDs.

TTSD-50086 Import, export, interoperability

Trimble Connector: PDF file attachments could not be opened in the Trimble Connector dialog box unless they had first been downloaded to the local computer by some other means, such as using Trimble Connect Desktop. Now double-clicking the PDF file attachment in the Trimble Connector ToDos dialog box will initiate the file download if necessary, and open the file in an associated viewer or browser.

TTSD-50359 Import, export, interoperability

IFC2x3 export: The export of the radial grids has been improved.

TTSD-50792 Import, export, interoperability

IFC4 export:  The IFC4 export Location by option Work plane now works. This option exports the model relative to the current work plane coordinate system. 

TTSD-51673 Import, export, interoperability

IFC4 export: The curved beam export sometimes produced incorrect geometry. This issue has now been fixed.

TTSD-53465 Import, export, interoperability

Trimble Connector: When exporting a model from Trimble Connector, sometimes the folder path could not be retrieved correctly from the Europe server. This issue has now been fixed.

TTSD-53472 Import, export, interoperability

IFC2x3 export: The UDA building hierarchy and GUID regeneration now work correctly.

TTSD-53699 Import, export, interoperability

Trimble Connector: The overlay models are now listed in the Trimble Connector dialog box when the collaboration is started.

TTSD-53839 Import, export, interoperability

Base points: You can no longer save a base point without giving a name for the base point.

TTSD-54200 Import, export, interoperability

Trimble Connector: The local \AppData folder contained two different folders for Trimble Connector, named \Trimble Connector and \TrimbleConnector. Now there is only one folder named \Trimble Connector.

TPLED-260 Templates and reports

Template Editor: When you select a content type in the Select Content Type dialog box after adding a row in Template Editor, the options in the list are now also sorted alphabetically in the translations. Previously, they were sorted correctly in English only.

TPLED-261 Templates and reports

Template Editor: Sometimes GetValue("ROW_IN_PAGE") returned an incorrect value when it was used in a row rule. This issue has now been fixed.

TTSD-20438 Drawings

Rebar marks: Previously, when XS_ENABLE_REBAR_MARK_LEADER_LINE_BASE_POINT_OPTIMIZATION was set to TRUE, any rebar mark leader line associativity points could be moved. Now the optimization is only applied to the marks that have the Placing method value Free. In practice, this prevents the optimization from moving manually moved marks, because moving a mark manually changes the value of its Placing method to Fixed.

TTSD-39833 Drawings

Rebar marks: Sometimes, when there was no frame around the reinforcement mark, and there was a circular frame around one of the mark elements, and you dragged the mark, the circular frame had a strange behavior: the frame was on top of the leader line in one end and moved slowly to the middle of the leader line in the other end. This behavior was observed when XS_MARK_LEADER_LINE_POSITION_TYPE_FOR_NO_FRAME was set to 4, where the leader line connects to the frame around the mark element. This issue has now been fixed.

TTSD-39990 Drawings

Rebar marks: Earlier, when you used the One leader line per row option for rebar marks, and the row was slanted, the mark might not be connected to the best side. This issue has now been fixed.

TTSD-42853 Drawings

Rebar marks: Earlier, when you created a rebar mark with the One leader line per row option for rebars along arc, a leader line with a partial zig zag shape was created. This issue has now been fixed.

TTSD-45613 Drawings

Rebar marks: A rebar mark that was created with applied properties did not work correctly on update. This has now been fixed.

TTSD-45705 Drawings

Linking drawings now works more reliably.

TTSD-45729 Drawings

Document manager: The document selections that you make in Document manager are now kept during the multi-user save. 

TTSD-53805 Drawings

Rebar marks: Earlier, showing the minimum length and maximum length for a tapered rebar group in a reinforcement mark was only taking into account the rebars inside the drawing view boundary. This issue has now been fixed, and these parameters now show the minimum and maximum length within the rebar group, irrespective of the drawing view boundary.

TTSD-54206 Drawings

Drawing texts: Earlier, the Background mask setting in Text properties did not follow toggle check box changes. This issue has now been fixed.

TTSD-44792 System and options

Previously, using the Save as command did not sometimes work correctly if the original model was created in Tekla Structures 2017 or older. This has now been fixed.

TTSD-52271, TTSD-52268 Tekla Model Sharing

Previously, Tekla Model Sharing features became inactive after the first write out or read in when using the Construction Modeling, Production Planner, EPM Modeler, Project Viewer, Drafter, or Carbon license. This has now been fixed.

TTSD-53184 Tekla Model Sharing

Previously, in Tekla Model Sharing, the read in icon was deactivated in some cases when the user with the Viewer role and the Project Viewer license read in more than one package. This has now been fixed.

TTSD-53236 Tekla Model Sharing

When a Tekla Model Sharing user has the Project viewer role, Tekla Structures now prevents modifications which would later cause the write out to be rejected, such as grid modifications.

TSAC-6877 Modeling

Previously, when placing surface treatment attributes and the product_finishes.dat file in the XS_PROJECT or in the model folder, the No paint area component did not load the subtype of the surface treatment correctly. This has now been fixed.

TTSD-20503 Modeling

Previously, if you modified a selection filter and clicked Apply or OK in the Selection Filter dialog box, standard was shown instead of blank for the applied selection filter on the Selecting toolbar. This issue has now been fixed.

TTSD-50354 Modeling

Previously, the direct modification commands stopped working when you used the Enter key to complete numeric input. This has now been fixed, and using the Enter key to complete the numeric input does not end the direct modification commands anymore.

TTSD-50407 Modeling

Previously, the Undo command did not work as expected. This has now been fixed, and Undo works again.

TTSD-50980 Modeling

Previously, Tekla Structures stopped working if XS_PROJECT contained subfolders in a language that was not supported by the current Windows locale. This has now been fixed.

TTSD-52971 Modeling

When objects.inp was edited by changing the user-defined attribute type after the values were set, the UDA values of the incorrect type were not reported correctly, and you could not fix them.

Now Diagnose & repair detects and fixes the the incorrect type by reverting the value to the default value.
 

TTSD-53103 Modeling

Sometimes when multi-user models were saved, the length of some bolts might have changed. This issue has now been fixed.

TTSD-53312 Modeling

When the advanced option XS_DELETE_UNNECESSARY_POLYGONPARTS is set to TRUE, using the Repair model command now makes very large model database files (.db1) significantly smaller.

TTSD-54607 Modeling

Sometimes, Tekla Structures might have stopped working when objects were copied or moved to another object in the model. This does not happen anymore.

TTSD-49612 Core

Previously, Tekla Structures process stayed running in the background when Tekla Structures was closed while a command was active. This does not happen anymore.

TTSD-49370 Numbering

Non-geometrical updates, such as changing the bolt type from Site to Workshop, now mark bolts as modified.

TTSD-43617 Import, export, interoperability (steel)

NC/DSTV: Earlier, depending on how the bent plate was created, the exported KA block only showed short bending lines or sometimes no lines at all. This issue has now been fixed.

TTSD-50317 Import, export, interoperability (steel)

NC/DSTV: Earlier, when you used the DSTV export for a CC profile, depending on the bolt rotation, the BO block could be created on the front or back profile face, causing missing holes in certain viewers. This issue has now been fixed, and the BO block for such holes is always created on the back profile face.

TTSD-51155 Import, export, interoperability (steel)

NC/DSTV: Earlier, when you exported an I beam or an RHS beam with countersunk bolts going through both flanges, countersunk information was not written to the NC file. This issue has now been fixed.

TTSD-51573 Import, export, interoperability (steel)

NC/DSTV: Earlier, studs that were modeled on the back plane of a C profile were exported on the front plane. This issue has now been fixed.

TTSD-54549 Import, export, interoperability (steel)

NC/DSTV: Earlier, drilled holes (holes modeled by cut) that were converted to bolt holes through the Maximum diameter for circular cuts to be drilled export setting did not follow the XS_CNC_HOLE_DIAMETER_ROUNDING advanced option. This issue has now been fixed.

TSAC-5583 Import, export, interoperability (concrete)

Export EliPLAN export (68): Position in Z is now exported for filled cores.

TSAC-6368 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, some reinforcing bars copied from an existing braced girder were recognized as braced girders. This issue has now been fixed, and only elements specified by class or by name are recognized as braced girders.

TSAC-6981 Import, export, interoperability (concrete)

Export Unitechnik (79): If a contour polygon contains edges shorter than 10 mm, a notification will be added in the Unitechnic log file.

TSAC-6984 Import, export, interoperability (concrete)

Export EliPLAN file (68): Previously, some elements with complex geometry were exported with incorrect length. This issue has now been fixed.

TSAC-6997 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, the Z coordinate of the electric tubes was not exported at all. This issue has now been fixed.

¿Le ha resultado útil?
Anterior
Siguiente