TSAC-5373 |
Concrete components |
Rectangular column reinforcement (83): Previously, intermediate links were created in the wrong direction if you set negative bottom offset in stirrup group 5. This has now been fixed. |
TSAC-5615 |
Concrete components |
Floor layout: The layer part UDA values from the second User defined tab are now correctly populated to layer parts. |
TSAC-5675 |
Concrete components |
Embedded anchors (8): Calculating anchor placing for steel assemblies and parts is now working properly. |
TSAC-5705 |
Concrete components |
Strip footing reinforcement (75): Stirrup hook properties are now read properly from the rebar database. |
TSAC-5714 |
Concrete components |
Reinforced concrete stair (95): There are now 6 new UDA lines on UDA tab. |
TSAC-5743 |
Concrete components |
Embedded anchors (8): On the Input tab, the custom part configuration file name can now have up to 79 characters. Previously, the name could have 22 characters. |
TSAC-5771 |
Concrete components |
Sandwich wall window: You can now select how to create the filler parts as insulation on the Bottom detail, Left detail, Right detail, Top detail, Door side detail, and Door bottom detail tabs. The filler parts can be created as the shell properties or as the insulation properties.
The image for continuous slope is now again shown on the Door side detail and Door bottom detail tabs. |
TSAC-5825 |
Concrete components |
Mesh bars: Meshes outside the slabs are now positioned exactly in the same way as the rebar groups. |
TSAC-5907 |
Concrete components |
Mesh bars by area: Mesh bars by area are now created on the part face where the selected area is when all faces are equally large and the up direction is set to auto.
|
TSAC-4345 |
Steel components |
Cap plate detail: When you open the properties dialog box of an existing component, the Class property is now shown correctly. |
TSAC-5755 |
Steel components |
U.S. Base plate (1047): Previously, some holes in the cast plate were missing. This has now been fixed.
|
TSAC-5793 |
Steel components |
Welded beam to beam (123): You can now define a name for the stiffeners on the Parameters tab. |
TSAC-5806 |
Steel components |
Pipe doubler plate now works for pipes with greater diameters. |
TSAC-5879 |
Steel components |
Gusset+T: On the Main part welds tab, you can now select a continuous, chain intermittent, or staggered intermittent weld shape.
|
TSAC-5880 |
Steel components |
Tube-Chamfer, Tube-Crossing Saddle, Tube-MitreSaddle+Hole, Tube-Saddle+Hole, Tube-Slotted Hole: On the Welding tab, you can now select a continuous, chain intermittent, or staggered intermittent weld shape.
|
TTSD-45400 |
Import, export, interoperability |
Export drawings to DWG/DXF: The view placement in the export was improved to prevent overlapping view content. |
TTSD-45449 |
Import, export, interoperability |
IFC object conversion: You can now have dots (.) in the property set names in the IFC object conversion UDA mapping. |
TTSD-45808 |
Import, export, interoperability |
Trimble Connect: The cs.dll and .cs.pdb files are generated when macros are compiled. These files are ignored from folder sync operation. Thus, addition of these two files in the local folder will not trigger an update. |
TTSD-46984 |
Import, export, interoperability |
Reference models: The performance of selecting a reference model list group and canceling the selection has been improved. You can notice the improvement when you have lots of reference model groups, and you select or cancel the selection of any object in the model. |
TTSD-46994 |
Import, export, interoperability |
Export drawings to DWG/DXF: Surface treatment drawn with invisible lines no longer hides content under it in the exported drawing DWG files. |
TTSD-47152 |
Import, export, interoperability |
IFC2x3 export: Weld coloring has been improved when you use current view colors. |
TTSD-47248 |
Import, export, interoperability |
IFC2x3 export: Antisymmetric (e.g. angle L50*5) polybeam profiles sometimes had wrong rotation when the extrusion export format was used, like in the Export To Aveva extension. This has now been fixed. |
TTSD-47598 |
Import, export, interoperability |
Reference models: The performance of inserting a reference model, and then undoing and redoing this has been improved. |
TTSD-46683 |
Templates and reports |
Sometimes, a large report using the CopyField function could take a long time to complete. This has now been fixed. |
TTSD-46788 |
Templates and reports |
When a revision was created for a drawing and the NextValue() function was used in a part row rule with a hierarchy, there could be rows missing from the template output. This has now been fixed. |
TTSD-46843 |
Templates and reports |
Previously, CUSTOM.ELEMENT_WEIGHT.REINFORCED summed the weight of the concrete main part reinforcement as many times as there were concrete parts in the cast unit. This has now been fixed.
CUSTOM.ELEMENT_WEIGHT.REINFORCED now works similarly to CUSTOM.ELEMENT_WEIGHT and shows the value for all cast unit parts. Previously, CUSTOM.ELEMENT_WEIGHT.REINFORCED showed the value for the main parts only. |
TTSD-47299 |
Templates and reports |
With imperial units, rows were not always combined when the rows had sort fields with "Numbers with decimals" as the data type. This has now been fixed. |
TTSD-47487 |
Templates and reports |
In an earlier service pack, templates and reports that had a REVISION row as the parent row did not show revision data, and you needed to place the REVISION row under the DRAWING row. This was changed to support both kinds of revision templates: with REVISION row alone and with DRAWING parent row. Now old revision templates work without any changes. However, it does not harm anyhow if templates would contain the DRAWING parent row. |
TTSD-33399 |
Drawings |
A new user-specific advanced option, XS_VIEW_FRAMES_VISIBLE, has been added in the Drawing View category of the Advanced Options dialog box:
- When you set this advanced option to FALSE, the drawing view frames are hidden until you move the mouse pointer over the view. This is the default value.
- When you set this advanced option to TRUE, the drawing view frames are visible all the time.
- In Tekla Structures versions 2019 and earlier, the drawing view frames were always visible. In Tekla Structures version 2019i, the drawing view frames were hidden and only displayed when the mouse pointer was over the view frame.
|
TTSD-42351 |
Drawings |
Dimensions in detail views now hold their positions better. |
TTSD-44668 |
Drawings |
Previously, if a model contained empty assemblies, drawing could not sometimes be opened because numbering was requested even when the model had been numbered. This has now been fixed. |
TTSD-44793 |
Drawings |
Document manager: Application error no longer occurs when Document Manager scans for file documents on certain types of network shared drives. |
TTSD-46924 |
Drawings |
Layout editor: Adding new tables now works slightly better in some special cases. |
TTSD-46933 |
Drawings |
Sometimes, an application error occurred during the cloning of the weld marks. This has now been fixed. |
TTSD-47155 |
Drawings |
Reference models: Reference models with wireframe representation are now drawn to the correct layer. Drawing to incorrect layer caused problems in the drawing order and cover-up areas, for example. |
TTSD-47439 |
Drawings |
Document Manager: Document manager now rounds fractional metric sheet sizes to whole numbers. |
TTSD-48140 |
Drawings |
Document manager: Document manager now automatically updates the document list for file documents when files change in the monitored areas. |
TTSD-46958 |
Tekla Model Sharing |
Previously, when joining a shared model, there could occasionally be an application error in Tekla Structures. This has now been fixed. |
TTSD-47417 |
Tekla Model Sharing |
Users with Viewer or Project viewer roles can now join shared models again. |
TSAC-5537 |
Reinforcement |
Rebar shape manager: In the RebarShapeManager.CustomProperties.dat file, it is now possible to define any user-defined attribute or any of the following built-in properties to be used as a custom property:
NAME, GRADE, SIZE, CLASS, proSERIE, proSTARTNUMBER.
Use proSERIE for the numbering prefix and proSTARTNUMBER for the start number. |
TTSD-44641 |
Reinforcement |
Rebar sets: Setting invalid values for spacing zones in the property pane no longer causes Tekla Structures to close suddenly. |
TTSD-46902 |
Reinforcement |
If a curved, circular, or circular spiral reinforcing bar had a very small bending radius, an error dialog box was shown, for example, when the bar was exported, or when bar information was inquired or reported. The dialog box will not be shown anymore. |
TSAC-5824 |
Modeling |
Auto bolt has been improved to work more reliably on parts with long narrow faces as well as for input points which fall on the edge of the input part solid. |
TTSD-46781 |
Modeling |
Clash check manager: Previously, running a clash check for certain models that contained bolts could cause an application error in Tekla Structures. The error was caused by a fast and linear increase in memory consumption. This has now been fixed. |
TTSD-46865 |
Installation |
Previously, when proxy settings were defined in TeklaStructures.exe.config, instead of starting, the C:\Program Files\Tekla Structures\2020.0\nt\bin folder was opened. This has now been fixed. |
TTSD-47353 |
Analysis and design |
The steel, concrete, and timber design properties that you modify in the Analysis Model Properties dialog box are now correctly passed to the linked analysis application (STAAD, Robot, SAP2000). |
TTSD-47642 |
Core |
Application error no longer occurs if the model macro closing all model views is executed in the drawing mode. |
TTSD-45800 |
Tools and components |
The possibility to add the UDA button for components in the Property Pane Editor has now been removed. Previously, the button has been removed from the property pane template for components in the Property Pane Editor, as it could cause an application error. |
TTSD-46711 |
Numbering |
Changing the assembly prefix/start number in the main part properties resets the assembly numbering, even when the prefix/start number was set in the assembly properties, thus making the change to have no effect on the assembly numbering. This could lead to assembly getting next number for no reason. This has now been fixed.
|
TTSD-43380 |
Import, export, interoperability (steel) |
NC/DSTV export: The NC export no longer generates NC files for parts that have failing geometries. The NC and session history logs report these failures. |
TSAC-5604 |
Import, export, interoperability (concrete) |
BVBS export: For 3D bent bars, the bending angle recognition tolerance is now 1.0 degrees. Neighboring leg segments with very small angles in between are exported as combined straight segments. The 3D bars with more than 4 handle points with small bending angles no longer stop the export. |
TSAC-5679 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): The export of the line attributes has been improved for sandwich elements. |
TSAC-5692 |
Import, export, interoperability (concrete) |
BVBS export: Mainly straight sections with minimal bendings in multiple directions now have more tolerance to be recognized as straight. Thereby both straight and bent rebars with such sections are handled better. |
TSAC-5763 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): On the new Symbols tab, you can specify if the braced girders exported with end symbol mountpart should also have a line representing the girder width (Draw girder width symbol), and if the braced girders are exported in the second shell of the double wall (Draw girder in second shell). You can now also specify the length of the longitudinal line. |
TSAC-5775 |
Import, export, interoperability (concrete) |
Export ELiPLAN file (68): Previously, the project name and project number were switched in the exported file. This has now been fixed. |
TSAC-5788 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): Previously, the Cuts as mountparts setting on the TS configuration tab did not work with some of the cuts at contour edges in simplified contours (Export CONTOUR was set to Simplified). This has now been fixed. |
TSAC-5802 |
Import, export, interoperability (concrete) |
Export ELiPLAN file(68): Previously, end recesses were ignored in aligning the weep holes at slab ends. This has now been fixed. |
TSAC-5804 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): Previously, when exporting the insulation panels as layers, the panels extending outside concrete that had gaps between the panels resulted in complex contour lines with notches difficult to be utilized in plotting, for example. Now such gaps between panels do not affect the extended contour. |
TSAC-5814 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): You can now choose if an insulation layer affects the contour using the new options, Layer cut to contour and Extend contour, on the Embeds tab. These options are only available if the insulation is exported as a layer within the concrete element and you have set the Export insulation setting to As concrete panel or As layers and embeds. When Layer cut to contour is used, the shuttering is placed by the determined concrete edge, however any insulation mountpart is allowed to extend outside this contour. |
TSAC-5819? |
Import, export, interoperability (concrete) |
Export Unitechnik (79): Previously, when reinforcement was exported as mountpart, the Z coordinate of the mountpart was not exported. This has now been fixed. |
TSAC-5843 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): Previously, info text 1 and 2, and also various other attributes were not exported for braced girders as mountparts. This has now been fixed. |
TSAC-5851 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): A new tab, Symbols, has been added where you can configure the details of mountpart symbols used in the export. All symbol-related settings have been moved from the Embeds tab to the Symbols tab. Also, new options for plotting placing symbols for braced girders have been added on this new tab. |
TSAC-5948 |
Import, export, interoperability (concrete) |
Export ELiPLAN file (68): The Product code setting on the Data content tab has new options Template and Cast unit prefix. For Product code, Accessory code and Material code, you can now specify multiple UDAs by separating them with a blank space. |
TSAC-5977 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): In recent service packs, when you tried to use a manual code in the line attribute override of a surface object, the resulting line attribute was invalid. This has now been fixed. |