Run combined analysis and member design
Run a combined analysis and design in order to rapidly check/design every concrete member or steel member, or every concrete member and steel member, for active gravity, static, or RSA load combinations.
Run Design Steel (Gravity)
On the Design tab, click 
Design Steel (Gravity).
Design Steel (Gravity).
Tekla Structural Designer analyzes gravity combinations only, and then designs all steel beams and columns in the model.
After design, the original member design mode assigned to each member can either be retained or updated. (For example, you might typically reset auto-designed steel members into check mode if they have a pass status.) The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design Steel (Static)
On the Design tab, click 
Design Steel (Static).
Design Steel (Static).
Tekla Structural Designer analyzes all static combinations and then designs all steel beams and columns in the model.
After design, the original member design mode assigned to each member can either be retained or updated. (For example, you might typically reset auto-designed steel members into check mode if they have a pass status.) The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design Steel (RSA)
Note: RSA load combinations must be
set up in advance of RSA Design by running the Seismic Wizard (choosing
the option to use Modal Response Spectrum Analysis).
Note: Additional considerations may
be necessary when designing members and walls for seismic analysis, see Seismic design methods in the Seismic analysis and
design handbook.
On the Design tab, click 
Design Steel (RSA).
Design Steel (RSA).
Tekla Structural Designer analyzes all Seismic RSA combinations and then designs all steel beams and columns in the model.
After design, the original member design mode assigned to each member can either be retained or updated. (For example, you might typically reset auto-designed steel members into check mode if they have a pass status.) The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design Concrete (Gravity)
On the Design tab, click 
Design Concrete (Gravity).
Design Concrete (Gravity).
Tekla Structural Designer analyzes gravity combinations only, and then designs all concrete beams, columns and walls in the model.
After design, the original member design mode assigned to each member can either be retained or updated. The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design Concrete (Static)
On the Design tab, click 
Design Concrete (Static).
Design Concrete (Static).
Tekla Structural Designer analyzes all static combinations and then designs all concrete beams, columns and walls in the model.
After design, the original member design mode assigned to each member can either be retained or updated. The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design Concrete (RSA)
Note: RSA load combinations must be
set up in advance of RSA Design by running the Seismic Wizard (choosing
the option to use Modal Response Spectrum Analysis).
Note: Additional considerations may
be necessary when designing members and walls for seismic analysis, see Seismic design methods in the Seismic analysis and
design handbook.
On the Design tab, click 
Design Concrete (RSA).
Design Concrete (RSA).
Tekla Structural Designer analyzes all Seismic RSA combinations and then designs all concrete beams, columns, and walls in the model.
After design, the original member design mode assigned to each member can either be retained or updated. The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design All (Gravity)
On the Design tab, click 
Design All (Gravity).
Design All (Gravity).
Tekla Structural Designer analyzes gravity combinations only, and then designs all steel and concrete beams and columns and all concrete walls in the model.
After design, the original member design mode assigned to each member can either be retained or updated. (For example, you might typically reset auto-designed steel members into check mode if they have a pass status.) The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design All (Static)
On the Design tab, click 
Design All (Static).
Design All (Static).
Tekla Structural Designer analyzes all static combinations and then designs all steel and concrete beams and columns and all concrete walls in the model.
After design, the original member design mode assigned to each member can either be retained or updated. (For example, you might typically reset auto-designed steel members into check mode if they have a pass status.) The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.
Run Design All (RSA)
Note: RSA load combinations must be
set up in advance of RSA Design by running the Seismic Wizard (choosing
the option to use Modal Response Spectrum Analysis).
Note: Additional considerations may
be necessary when designing members and walls for seismic analysis, see Seismic design methods in the Seismic analysis and
design handbook.
On the Design tab, click 
Design All (RSA).
Design All (RSA).
Tekla Structural Designer analyzes all Seismic RSA combinations and then designs all steel and concrete beams and columns and all concrete walls in the model.
After design, the original member design mode assigned to each member can either be retained or updated. (For example, you might typically reset auto-designed steel members into check mode if they have a pass status.) The action that is taken is controlled via .
On completion of the design the ribbon switches to the Review tab and a Review View opens to allow you to inspect the pass/fail status and utilization ratio of each member.