2022 SP3: New features, improvements, and important fixes

Tekla PowerFab
2022
Tekla PowerFab Tekla PowerFab GO

2022 SP3: New features, improvements, and important fixes

The latest Tekla EPM 2022 service pack is available in Tekla Downloads.

Korrigeringar

Defektnummer Utvecklingsområde Beskrivning
EPM-6509 Estimating

In Estimating, the Fabrication Summary report has been redesigned in Stimulsoft Reports.

EPM-6638 Estimating

Support has been added for Checked and Unchecked as well as True/False, T/F, and 1/0 as ways to denote the main piece on an Excel/Bluebeam import.

EPM-6751 Estimating

In Estimating, a company standard setting has been added to indicate if the Summary Information to Excel report option should prompt when it is a Canadian project for the purposes of applying tax rates.

EPM-6826 Estimating

Previously, in Estimating, the Fabrication Summary report might have shown incorrect values for the sand shot and labor cost. This issue has now been fixed.

EPM-6729 Project management

The Find filter dialog is now much faster to open when there are many (thousands of) options to add to the selection.

EPM-6740 Project management

All Project Management reports have been redesigned in Stimulsoft Reports.

EPM-6853 Project management

In Project Management, the global drawing list reports that were redesigned in Stimulsoft Reports in 2022SP2 show an incorrect job number in the page header. This issue has now been fixed.

EPM-6918 Project management

In Project Management, the built-in change order, RFI, and transmittal reports are now available for the list of available reports to be run or designed.

EPM-6938 Project management

Previously, a "File does not exist" error occurred when emailing a request for information (RFI) or transmittal. This issue has now been fixed.

EPM-6622 Production control

Previously, in Production Control, the filters on the main dialog might not have been applied correctly when there was a Sequence and/or Lot # filter set along with the Date Station Completed filter. This issue has now been fixed.

EPM-6623 Production control

Previously, in Production Control, an error occurred when running shipping ticket reports for accessory parts that were on the same load as the main member. This issue has now been fixed.

EPM-6633 Production control

 

Previously, when an EPM database contained more than one External Nest with the same GUID (from the external software), the TFS command might fail due to not finding a connected inventory item. This issue has now been fixed.

EPM-6648 Production control

Previously, in Production Control, cut list reports could show the plate width in a header that was meant to only represent the thickness of the plate. This issue has now been fixed.

EPM-6674 Production control

In Production Control, the Bill of Materials report that was converted to Stimulsoft Reports in 2022SP2 now displays the correct length.

EPM-6639 Administration

When using a MySQL 5.7 database, the general performance of the application is significantly improved, particularly for large batch operations.

EPM-6673 Administration

Previously, in Administration, the Check/Repair command could result in an error. This issue has now been fixed.

EPM-6686 Administration

Tekla EPM can now be run while FIPS encryption mode is enabled.

EPM-6845 Administration

When using a MySQL 5.0.90 database, if a users access to Tekla EPM was revoked and then immediately given again, this resulted in an error. This issue has now been fixed.

EPM-6874 Administration

Previously, when the application exited due to the idle session time-out, an error could appear. This issue has now been fixed.

EPM-4863 Purchasing

Previously, the Pricing Update dialog box did not show the correct price for the selected supplier if another supplier had the Always Buy From option checked for that material. This has now been fixed, and the Pricing Update dialog  now reflects the pricing on a material according to the supplier selected, even if a different supplier is selected as the Always Buy From for this size.

EPM-5937 Purchasing

In Purchase Orders, an error can occur attempting to receive a line item that previously had ASN details imported.

EPM-6634 Purchasing

When adding a file into the Document Index, the target directory is now created automatically if it does not already exist.

EPM-6559 Inventory

In Inventory, transaction history reports have been added to show the changes to the inventory, summarized by transaction type, that occurred within the selected transaction date filter.

EPM-6710 Inventory

Previously, when completing an inventory location sweep, an incorrect quantity could be moved to the "lost" location when it should only have been the quantity not scanned. This issue has now been fixed.

EPM-6804 Inventory

Previously, in Inventory, when running transaction history reports, the filters were not applied correctly to unreceive transactions. This issue has now been fixed.

EPM-6698 Requisitions

In Requisitions, all of the reports have now been redesigned in Stimulsoft Reports.

EPM-6830 Combining

Previously, the combining run results did not take the squaring amount into account when computing the drop length. This issue has now been fixed.

EPM-6619 Integrations

When importing into Production Control with a file from SDS/2, erection drawings are now imported properly.

EPM-6652 Integrations

Previously, the Bill of Material fields from SDS/2 did not map properly. This issue has now been fixed.

EPM-6685 Integrations

Previously, when importing nesting results from ProNest, it was possible for an inventory plate to be utilized when it should have been added to a requisition instead. This issue has now been fixed.

EPM-6706 Integrations

 

Previously, the options in the ProNest Name dropdown menu in ProNest Settings included Material Description. This has now been changed to Shape Grade Thickness.

EPM-6723 Integrations

When syncing inventory with SigmaNest, the job reserve field in SigmaNest is now populated.

EPM-5011 Inspections

In Inspections, the Inspection Test Records and Inspection Test Records with Notes reports now display any images attached to the inspection records and list the file names of any other attached documents.

Var det här användbart?
Föregående
Nästa