Material Handling Components

Tekla Structures
2021
Tekla Structures
2020
Tekla Structures
2019i
Tekla Structures
2019
Tekla Structures
2018i
Tekla Structures
2018
Tekla Structures
Environment
United States (Imperial)
United States (Metric)
CATALOG NAME: Material Belt-Idler Array; Material Idler; Material Support 1 (bent); Material Support 2 (bent); Material Truss; X-Brace (Angle); X-Brace (Tube); X-Brace (W-WT)

Material Belt-Idler Array
TYPE: SEAM

This custom component allows you to quickly add a material idler array to a truss along a beltline path. The custom component is base on the same reference line (beltline) in order to help with design.

Picking order:
1.  Select 1st horizontal frame member. (Can be either top, or bottom.)
2.  Select 2nd horizontal frame member. (Can be either top, or bottom, but consistent with the first.)
3.  Select 1st layout point for beltline.
4.  Select 2nd layout point for beltline.
Image
matl_belt-idler_array1.gif
 
Image
matl_belt-idler_array2.gif


Image
matl_belt-idler_array3.gif


Material Idler - Back to top
TYPE: PART

This custom component allows you to quickly add a single material idler to a truss. There may be conditions when the designer/detailer needs to make specific considerations.

Picking order:
1.  Select 1st layout point.
2.  Select 2nd layout point to indicate direction of input.

Image
matl_idler1.gif


Image
matl_idler2.gif


When using to indicate shimmed condition…

Image
matl_idler3.gif


…use the Position tab to adjust individual Idlers.

Image
matl_idler4.gif


Material support 1 (bent) - Back to top
TYPE: SEAM


This custom component allows you to add the support structure for material handling. It is necessary with this component to input foundation elements at either a conceptual or exact location to establish the base of the support. The top elevation is defined with the 3rd pick point placed at the beltline. The base width and the bottom elevation of the base are all defined initially by the 4th pick point.

Picking order:
1.  Select Primary foundation member
2.  Select Secondary foundation member
3.  Pick 1st Point (Beltline)
4.  Pick 2nd Point

Image
matl_spt1_bent1.gif



This component’s base is adjustable by moving the foundation members. Both in the x,y direction and in the z direction.

Image
matl_spt1_bent2.gif
 
Image
matl_spt1_bent3.gif
    

If component looks similar to the picture below, use the General tab and adjust the Up direction to rotate the objects into proper alignment. (+y,-y,-x,+x)

Image
matl_spt1_bent4.gif
 
Image
matl_spt1_bent5.gif
  

If the beltline follows an angle other than on a 90, use Auto to rotate the component to a specific angle in the plan.

Image
matl_spt1_bent6.gif


Material support 2 (bent) - Back to top
TYPE: SEAM


This custom component allows you to quickly add Vertical bracing in the formation of an X into the model between two beams. Select the primary beam to indicate the base and then select the secondary beam to indicate the extent of the braces. The span of the X-bracing is calculated by the distance between the 1st and 2nd Point.

Picking order:
1.  Select handle location of truss beltline.
2.  Select direction using belt as guide.

Image
matl_spt2_bent1.gif


This component’s direction is based on the second pick.

Image
matl_spt2_bent2.gif


It is necessary to grab the second handle when adjusting the height of the beltline in conjunction with the truss component.

Material truss - Back to top
TYPE: SEAM


This custom component allows you to quickly add a material truss along a beltline path. There is a representative part included for the beltline. This member is to help with the design process. Layout the beltline with construction points, lines, etc. and then, use these points to input the truss.

Picking order:
1.  Select 1st layout point for beltline.
2.  Select 2nd layout point for beltline.

Image
matl_truss1.gif


Image
matl_truss2.gif


X-Brace (Angle); X-Brace (Tube); X-Brace (W-WT) - Back to top
TYPE: SEAM; SEAM; SEAM


These custom components allows you to quickly add Vertical bracing in the formation of an X into the model between two beams. Select the primary beam to indicate the base and then select the secondary beam to indicate the extent of the braces. The span of the X-bracing is calculated by the distance between the 1st and 2nd Point.

Picking order:

1.  Select Primary Beam
2.  Select Secondary Beam
3.  Pick 1st Point
4.  Pick 2nd Point

Image
matl_xbrace_angle.gif


These components works on either an “A-Frame” or “H-Frame” condition.

Starting in v21.1, the above Custom Components are available in all US Environment Model Templates

  • CIP-Rebar Detailing (hidden)
  • Engineering*
  • Precast Detailing (hidden)
  • Steel Detailing (hidden)
Was dit nuttig?