Punching check properties

Tekla Structural Designer
2021
Tekla Structural Designer

Punching check properties

General
Tension Reinforcement This setting identifies the slab reinforcement to be used in the punching check calculation.
  • Top
  • Bottom
Center The check location (not editable).
Column Drop Indicates if the check considers a Column Drop (not editable).

Beta - User limit

(Head Code Eurocode)

When this checkbox is selected, a minimum value of Beta = 1.15 is applied to all internal columns.

User factor for Vt

(Head Code BS)

When this checkbox is selected, the user factor for Vt is applied.
u0 - user reduction Can be used to manually specify a reduction in the length of the u0 perimeter to account for undefined openings.
u1 - user reduction Can be used to manually specify a reduction in the length of the u1 perimeter to account for undefined openings.
Check Status and Ratio Indicates the status of the checks for each calculated perimeter and the overall check ratio.
Loaded Perimeter
Length Indicates the length of the u0 Loaded Perimeter (not editable).
Reduced length The reduced length of u0 after accounting for openings.
BEquiv, DEquiv, BBound, BBound, Bounding Perimeter Refer to the Concrete Design Reference Guide for the current Head Code for the appropriate definition of these terms.
d Effective Depth

Indicates the average effective depth to the tension reinforcement (not editable).

d = (dy + dz) / 2

where dy and dz are the effective depths in the two orthogonal directions.

There is a value of d for top steel and a different value for bottom steel. Note this definition changes in the presence of a drop panel.

This information is only available if the reinforcement is known in each direction.

Slab Override

When an override is applied the slabs in each direction can be de-activated in the check. In this way the Loaded Perimeter Position can be edited.

Note: In the typical case of punching checks around a column, the slab ‘y’ & ‘z’, ‘positive’ & ‘negative’ are defined by the local axis system of the column. This can be displayed by displaying the Local Axes for 1D Elements in Scene Content.
Control Perimeter
Length Indicates the length of the u1 Control Perimeter (not editable).
Reduced length The reduced length of u1 after accounting for openings.

[-] Design Input

(Head Code Eurocode and ACI)

Use Reinforcement

Select this checkbox in order to apply a default punching reinforcement arrangement that can then either be checked, or used as the starting reinforcement for an auto-design.

You would only choose to clear the checkbox when specifying a new check if you want to perform an auto-design but starting from Minima.

Reinforcement type In the current release only Stud reinforcement is considered.
Arrangement type

The options are:

• Orthogonal (default)

• Circular

Auto-design When run in Auto-design mode, the reinforcement is increased until either a pass is achieved or the limiting reinforcement parameter limits have been exceeded.
Select reinforcement starting from

This option controls the starting point for auto-design procedures and is therefore only displayed if Auto-design is ‘on’.

• Minima - removes the current arrangement and begins with the minimum allowed bar size.

• Current - auto-design commences from the current bar arrangement.

Rib type Specifies the reinforcement rib type.
Grade The reinforcement grades that are available here are set from the Materials button on the Home ribbon.
Bar size The reinforcement bar sizes that are available here are set from the Materials button on the Home ribbon.
Spacing Defines the spacing between bars along each rail.
Spacing from column face Defines the spacing of the first bar in each rail from the column face.
Stud rails spacing in Y direction Spacing between rails in the local Y direction.
Stud rails spacing in Z direction Spacing between rails in the local Z direction.
Number of diagonal stud rails on one corner

The number of stud rails adjacent to each corner of the column.

(This property is only displayed when the ‘Arrangement Type’ is Circular)

Number of studs per column face - Y direction The number of stud rails adjacent to the column face in the local Y direction.
Number of studs per column face - Z direction The number of stud rails adjacent to the column face in the local Z direction.
Number of studs per rail Number of studs on each rail.
Utilization ratio
Apply (to autodesign) On
  • When an Autodesign is performed, the design will be incremented to achieve a utilization ratio less than the ratio limit.
Off
  • When an Autodesign is performed, the design will be incremented to achieve a utilization ratio less than 1.0.

See: Apply user defined utilization ratios

Apply (to check) On
  • When a Check is performed, the check will pass provided the utilization ratio is less than the ratio limit.
Off
  • When a Check is performed, the check will pass provided the utilization ratio is less than 1.0.
Ratio limit The utilization ratio against which the autodesign or check is performed (when applied above).
Design Input (Eurocode and ACI only)
Use Reinforcement

Select this checkbox in order to apply a default punching reinforcement arrangement that can then either be checked, or used as the starting reinforcement for an auto-design.

You would only choose to clear the checkbox when specifying a new check if you want to perform an auto-design but starting from Minima.

Reinforcement type In the current release only Stud reinforcement is considered.
Arrangement type

The options are:

• Orthogonal (default)

• Circular

Auto-design When run in Auto-design mode, the reinforcement is increased until either a pass is achieved or the limiting reinforcement parameter limits have been exceeded.
Select reinforcement starting from

This option controls the starting point for auto-design procedures and is therefore only displayed if Auto-design is ‘on’.

• Minima - removes the current arrangement and begins with the minimum allowed bar size.

• Current - auto-design commences from the current bar arrangement.

Rib type Specifies the reinforcement rib type.
Grade The reinforcement grades that are available here are set from the Materials button on the Home ribbon.
Bar size The reinforcement bar sizes that are available here are set from the Materials button on the Home ribbon.
Spacing Defines the spacing between bars along each rail.
Spacing from column face Defines the spacing of the first bar in each rail from the column face.
Stud rails spacing in Y direction Spacing between rails in the local Y direction.
Stud rails spacing in Z direction Spacing between rails in the local Z direction.
Number of diagonal stud rails on one corner

The number of stud rails adjacent to each corner of the column.

(This property is only displayed when the ‘Arrangement Type’ is Circular)

Number of studs per column face - Y direction The number of stud rails adjacent to the column face in the local Y direction.
Number of studs per column face - Z direction The number of stud rails adjacent to the column face in the local Z direction.
Number of studs per rail Number of studs on each rail.
Was dit nuttig?
Vorige
Volgende