Concrete console (110): On the Parameters tab, you can now cut the beam part around the column. Previously, you could only cut the column.

Floor layout: The Line up direction setting on the General tab now works correctly. Previously, if you had the insulation layer as the lower layer and changed the line up direction, the insulation was not created correctly.
 

Floor layout: The CIP filler part is no longer created outside the component polygon boundaries.

Automatic splicing tool: Single bars are now correctly split and spliced regardless of their direction. Previously, single vertical bars were not handled correctly.

Rebar end anchor now correctly creates end detail modifiers for rebar sets in cases where only one bar is affected.

Two sided clip angle (143): Previously, the flange cut created due to bolts clashing with the flange was not created for the second secondary beam in all situations. This issue has now been fixed.

Ring plate: The part and assembly start number of the ring plate are now modified when only the corresponding check boxes are selected. Previously, the part and assembly start number were not modified unless all the check boxes in the dialog box were selected.

Opening frame: The On plane and At depth offset values on the Parts tab for top frame, bottom frame and vertical posts are length values and they now use the correct units set in Options > Units and decimals. The Angle value for welds and Rotation angle on the Parts tab are angle values and they now use the correct units set in Options > Units and decimals.

Two sided end plate (142): Previously, safety connections were not correctly applied in all situations. This issue has now been fixed.

Gusseted cross (62): Previously, the bolt edge distance on the bracing side was not correctly applied from the joints.def file. This issue has now been fixed.

Cast-in plate (1069): Previously, the tab plate material was not applied correctly. This issue has now been fixed.

Gusset+ T: The stiffener chamfer is now created to the web of the main part.

Base plate (1042): Previously, the component was not rotated when you changed the Up direction on the General tab. This issue has now been fixed.

Column seating (39): Previously, bolts were not created for specific main part profile and bolt horizontal offset combinations. This issue has now been fixed.

UltraZED Non-std side rail (91): Previously, counterforming both sets of bolts reduced the strut length at one end. This issue has now been fixed.

Stiffened end plate (27): Previously, finger shim plates were created incorrectly in some cases. This issue has now been fixed.

End plate (144): Previously, finger shim plates were created incorrectly in some cases. This issue has now been fixed.

Stiffened end plate (27): Previously, one of the shear tab corner chamfers was not created correctly. This issue has now been fixed.

Previously, category properties did not open if the environment or model did not have any Organizer filters. This issue has now been fixed.

Earlier, when you had set XS_BOLT_DUPLICATE_IGNORE to TRUE, and exported a part as DSTV, some holes were not exported because another bolted part had holes in the same location. This issue has now been fixed.
Note that you should not use this advanced option in any new models. Instead, use the No hole option for Special hole type in the Bolt properties.

IFC export: Earlier, the IFC export result did not contain the properties for IfcBuilding and IfcBuildingStorey. Now these properties are shown.

IFC export: The Property set definitions dialog box now supports better the creation of the boolean property type. Also, an empty value stays empty when exported, it is no longer forced to TRUE.

Reference models: Sometimes the reference model list stopped responding when you scrolled the list in a certain use case. This issue has now been fixed.

Template Editor: Copying and pasting a text object that has the '$' character as its only content fails. This issue has now been fixed.

Template Editor: Sometimes, when you moved multiple objects horizontally using the Move Object dialog box, the objects also moved vertically. This issue has now been fixed.

The macros for relabeling section views and detail views are now able to handle views named with numbers correctly.

Earlier, when using a bolt hole mark with a template attribute in single-part drawing views, the main part hole information was always shown even though the secondary part had a different hole. This issue has now been fixed.

Fabrication drawings: The Creation review dialog box now supports some advanced options better for concrete parts.

Reference models in drawings: The DWG reference model texts in drawings are now drawn correctly also when the Outline representation is used.

Rebar sets: Previously, for a tapered rebar set bar group with two or more legs, at the point where the height became greater than the width (or vice versa), the leg dimensions in reports swapped around (DIM_A became DIM_B, and vice versa). This issue has now been fixed.

In the UK environment, the calculated weights of the profiles UB533x165x66 and UB533x165x75 were incorrect due to the cross sectional area being incorrect in the profile catalog. This issue has now been fixed.

Bolts: Earlier, in Tekla Structures 2022, if you modeled a bolt that went through two or more parts and that had a negative cut length, the bolt was placed incorrectly. This issue has now been fixed.

Previously, an empty cross section for weld preparation could cause Tekla Structures to stop working unexpectedly. This has now been fixed.

Rebar assemblies: The Locked user-defined attribute has now been added for rebar assemblies.

Bolts: Earlier, in Tekla Structures 2022, bolts were incorrectly positioned when beams or columns were deformed by shortening. The incorrect positioning occurred when XS_DRAW_BOLTS_3D_IN_BOLT_LAYER was set to TRUE and when the bolts had the Exact representation in model views. This issue has now been fixed.

Previously, when a formula or equation for a sub-object was removed in Custom component browser, it became visible again after clicking Refresh. This has now been fixed.

Previously, Tekla Structures occasionally shut down after a custom component was edited. This has now been fixed.

Export ELiPLAN file (68): The export of complex walls created by multiple concrete parts has been improved.

Export ELiPLAN file (68): Previously, duplicated records were exported for filled cores. This issue has now been fixed.

Export ELiPLAN file (68): Previously, the data conversion file mapping did not work for profiles that had parentheses in the profile name. This issue has now been fixed.

Export Unitechnik (79): Previously, loose reinforcement was exported as mesh. This issue has now been fixed.