TSAC-3912 |
Concrete components |
Wall layout: Modifying wall boundary offsets by using direct modification has been improved. Previously, the boundary offsets of a layer could stop working for some layers inside the wall. The issue that caused this has now been fixed.
|
TSAC-3931 |
Concrete components |
Formwork placing tools - Walls: You can now create front or back platforms. |
TSAC-4093 |
Concrete components |
Floor layout: Applying break lines now works correctly. You can add multiple break lines without having to re-click the break line button in the contextual toolbar. |
TSAC-4449 |
Concrete components |
Geometry detailing strip: The plane position and offset are now properly handled in Geometry detailing strip when the strip is applied on the face of a single part. Previously, the plane position and offset were handled properly only when applied on a wall layout or some other component. |
TSAC-5483 |
Concrete components |
Braced girder (88): Previously, hook length was not read properly from the rebar database for rebar sets that have a non-number size code in the database. This issue has now been fixed. |
TSAC-6207 |
Concrete components |
Hollowcore opening tool: Previously, openings were not created in certain situations. This issue has now been fixed. |
TSAC-6287 |
Concrete components |
Rebar shape placing tool: Previously, if placing data in the Rebar shape placing tool dialog box was changed while bar placing was active, Tekla Structures closed suddenly. This issue has now been fixed. |
TSAC-6330 |
Concrete components |
Sloping slab drainage: You can now define the slab class. |
TSAC-6357 |
Concrete components |
Floor layout: The CIP filler parts at the seams are now created correctly. Previously, slabs with cross sections that were only touching at one point in the seam were not recognized for CIP filler creation.
|
TSAC-6374 |
Concrete components |
Embed (1008): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6375 |
Concrete components |
Embedded anchors (8): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6376 |
Concrete components |
Concrete foundation (1030): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6377 |
Concrete components |
Reinforced concrete stair (95): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6379 |
Concrete components |
Corbel connection (14): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6380 |
Concrete components |
Seating with dowel (75), Two sided seating with dowel (76), Seating with dowel to flange (77), Two sided seating with dowel to flange (78): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6381 |
Concrete components |
Rebar in beam (90): Previously, component rebars were not always created properly in environments where the rebar size code is not an integer. This issue has now been fixed. |
TSAC-6389 |
Concrete components |
Mesh bars by area: Rebars are now recreated correctly after changing the spacing by using direct modification. |
TSAC-6391 |
Concrete components |
Formwork placing tools - Walls: You can now set vertical offset for platforms. |
TSAC-6398 |
Concrete components |
Wall layout: Previously, when modifying openings by using direct modification, the openings were not modified correctly if the main layer did not have an opening. This issue has now been fixed.
|
TSAC-6413 |
Concrete components |
Tapered I-beam (81): Previously, end detail cuts were not created correctly. This issue has now been fixed. |
TSAC-5991 |
Steel components |
Wraparound gusset cross (60): Gusset bolts are now created correctly when using erection clearance for clip angles. |
TSAC-6183 |
Steel components |
Splice plate 2 (62), Splice connection (77), Column splice (132): You can now define that slotted holes are created in parts.
|
TSAC-6202 |
Steel components |
Cast-in plate (1069): Previously, when using double tab plates, one of the tab plates had an incorrect width. This issue has now been fixed. |
TSAC-6300 |
Steel components |
Gusset stiffeners (171): Previously, upper and lower stiffeners were not created in some cases. This issue has now been fixed. |
TSAC-6301 |
Steel components |
Shear plate simple (146): Previously, weld backing bars were not created for C profiles with sloped flanges. This issue has now been fixed. |
TSAC-6315 |
Steel components |
Angle profile box (170): Previously, lower angle stiffeners were not created in the correct position. This issue has now been fixed. |
TTSD-40181 |
Import, export, interoperability |
IFC4 export: CUSTOM properties are now supported in the IFC4 export. |
TTSD-47171 |
Import, export, interoperability |
Overlay models: If a bolt has two nuts, the second nut is now rotated for better visualization. |
TTSD-48204 |
Import, export, interoperability |
Trimble Connect: The reference model update is now optimized when there is a lot of content in the folders, and the update is no longer blocking subsequent actions. |
TTSD-48688 |
Import, export, interoperability |
Trimble Connect: The upload to Trimble Connect now exports profiles correctly (for example, PLT16x280) also when the separator 'x' is used if the 'x' separator is defined for the XS_PARAMETRIC_PROFILE_SEPARATOR advanced option. |
TTSD-48974 |
Import, export, interoperability |
Trimble Connect: There was an occasional update error after a reference model upload. |
TTSD-49536 |
Import, export, interoperability |
IFC object conversion: The IFC object conversion now supports materials and the mapping of materials in Conversion as item (B-rep conversion). |
TTSD-49589 |
Import, export, interoperability |
IFC2x3 export: The progress bar and status messages have been removed from the IFC2x3 export dialog. The export progress is now shown in the common Tekla Structures progress dialog box, and the export status is indicated in the Tekla Structures status bar. |
TTSD-49798 |
Import, export, interoperability |
Trimble Connect: A rebar assembly rebar set was exported twice: First, correctly as groups, and then a second time incorrectly as a whole rebar set through the assembly. This has now been fixed, and the rebar set is exported only once as groups. |
TTSD-49922 |
Import, export, interoperability |
IFC4 export: Rebar groups are exported as IfcReinforcingBar, and the export may also contain additional property sets and properties. |
TTSD-50058 |
Import, export, interoperability |
Trimble Connect: When a reference model published from Trimble Connector was deleted remotely, it did not appear in the unpublished reference models list anymore. This issue has now been fixed. |
TTSD-50175 |
Import, export, interoperability |
Trimble Connect: Uploading to Trimble Connect by using the Layer names as: Name option is now also supported with rebar sets. |
TTSD-50267 |
Import, export, interoperability |
Project properties: The user-defined IFC export project attributes IFCSITE, IFCBUILDING and IFCBUILDINGSTOREY are now cleared when you save your model by using Save as. |
TTSD-50279 |
Import, export, interoperability |
Trimble Connect: The model upload to Trimble Connect failed if there were some extra files in the environment folder, for example, text files. This issue has now been fixed. |
TTSD-50323 |
Import, export, interoperability |
Reference models in multi-user mode: Undoing a reference model insert in the multi-user mode caused an error note in save. This issue has now been fixed. |
TTSD-50501 |
Import, export, interoperability |
IFC4 export: Rebar sets are aligned to a hierarchical object if they do not belong to an assembly. |
TPLED-229 |
Templates and reports |
Template Editor: The Valuefield basename was not kept in copying and pasting. This issue has now been fixed. |
TPLED-231 |
Templates and reports |
The ROW_IN_PAGE attribute did not work correctly when a table was filled by using the Fill direction: Horizontal setting. This issue has now been fixed. |
TPLED-235 |
Templates and reports |
Template Editor: Page headers and footers were sometimes missing with the Use columns property set. This issue has now been fixed. |
TPLED-236 |
Templates and reports |
Template Editor: The column gap in tables is no longer too narrow. Note that if column headers or footers were created by a fixed number of columns instead of using the Use columns property, then there can be a misalignment of column borders between cells and column headers or footers. In this case, edit the header or footer definitions by either using the Use columns property, or manually realigning the header or footer content. |
TPLED-237 |
Templates and reports |
Template Editor: Tables were sometimes places too low when multiple pages were used. This issue has now been fixed. |
TTSD-17729 |
Templates and reports |
Template Editor: Horizontal template output now works when the template uses a variable number of columns. |
TTSD-46625 |
Templates and reports |
Previously, the values returned by the template attributes END1_CODE and END2_CODE were not correct for polybeams. This has now been fixed. |
TTSD-49576 |
Templates and reports |
Sometimes, templates were misplaced in the drawing layout when template columns were filled from right to left (the Start from setting was set to Top right or Bottom right in Template Editor row properties). This issue has now been fixed. |
TTSD-30067 |
Drawings |
Welds no longer disappear from drawings when parts are checked for hidden lines. |
TTSD-45316 |
Drawings |
Section marks or labels no longer disappear when you modify a drawing. |
TTSD-49385 |
Drawings |
Fabrication drawings: In the Creation review dialog box, selecting a drawing template in the Create from list in the Smart create mode is now easier when the assembly name information is visible for each entry.
|
TTSD-49768 |
Drawings |
Rebar set groups: Previously, rebar set groups were 'exploded' in drawings if they were found to contain multiple pours, for example, due to a pour break. Now, rebar set groups are only exploded in GA drawings where Show pours in drawing is set to Yes. Note that GA drawings created prior to this change that have Show pours in drawing set to No, have to be recreated by switching Show pours in drawing to Yes and then back to No to display the rebars correctly. |
TTSD-49988 |
Drawings |
Document manager: Document manager was not able to show file changes for monitored folders if the folder path contained non-Latin characters. This issue has now been fixed. |
TTSD-50024 |
Drawings |
Fabrication drawings: The file selection in the Smart create overrides list in the Creation review dialog box is now synchronized with what has been selected in the Smart create overrides dialog box. |
TTSD-50232 |
Drawings |
Earlier, when you had set the XS_BOLT_DUPLICATE_IGNORE advanced option to TRUE , certain studs were sometimes considered as duplicates. Due to to this, these studs were not shown in drawing views. This issue has now been fixed. |
TTSD-50604, TTSD-50542 |
Drawings |
The Create cut line command in drawings now works. |
TTSD-50801 |
Drawings |
Earlier, rebar marks with perpendicular lines were created with inclined lines. This issue has now been fixed. When you define the rebar marks in view properties, ensure that you set the frame type and color. The environments should also have appropriate rebar mark properties defined including desired frame type and color. |
TTSD-49481 |
Tekla Model Sharing |
In Tekla Model Sharing, the logging for model sharing network failures has been improved. |
TTSD-46830 |
Reinforcement |
Rebar sets: Leg faces can now be selected also by clicking on an edge of the leg face. |
TTSD-48920 |
Reinforcement |
Rebar sets: The commands Attach to part and Detach from part have been added to the property modifier context menu. You can use the commands to manually assign rebar set bars that intersect the property modifier to a concrete part. |
TTSD-50035 |
Reinforcement |
Rebar sets: Previously, if part labels were visible in model views, numbering objects left rebar sets unnumbered if the rebar sets were affected by surfaces that defined concrete cover thickness values. This issue has been fixed. |
TTSD-50138 |
Reinforcement |
Rebar sets: An issue was fixed where selecting a rebar set with a certain leg surface caused Tekla Structures to stop responding and close suddenly. |
TTSD-50278 |
Reinforcement |
Rebar sets: An issue was fixed whereby the first or last bar in exact spacing with flexible first or last space was missing when the flexible space was very small. The logic for exact spacings has been changed to match that of rebar groups. |
TTSD-50299 |
Reinforcement |
Rebar sets: An issue was fixed whereby after using the rebar set layer editing commands, the coupler and end anchor components would sometimes not place those objects correctly. |
TTSD-50304 |
Reinforcement |
Rebar sets: In rebar sets that contained overlapping leg faces, the geometric projection of modifiers might sometimes be incorrect and the modifiers might not be applied to the correct bars. This issue has now been fixed. |
TTSD-14557 |
Modeling |
When inserting or adapting surfaces and rebar set leg surfaces, duplicate surfaces with the same type on the same face are now removed. |
TTSD-36146 |
Modeling |
Surface object adaptivity has been improved for polybeams and it now works in many polybeam use cases, including polybeam curved surfaces and profile changes. |
TTSD-43960 |
Modeling |
Previously, the right-click context menu did not show all the commands correctly and Tekla Structures restart was needed to get the menu to work correctly. This has now been fixed.
|
TTSD-45502 |
Modeling |
Previously, the commands to create construction circles, arcs, and polycurves did not follow the setting of the Snap to any position switch. This now has been fixed. |
TTSD-48745 |
Modeling |
Previously, sometimes when a radial grid had a manually added grid line, the reports of the parts located on the added grid line were showing incorrect part position on the grid. |
TTSD-49871 |
Modeling |
Previously, corner chamfers were lost in certain situations when a slab or plate that was placed on a user-created work plane was being split. This has now been fixed.
Additionally, picking points on chamfered plates or slabs on the work plane now works correctly. |
TTSD-49952 |
Modeling |
Previously, when the bolt diameter was specified as a decimal number, it might happen that incorrect bolt properties were selected from the bolt assembly catalog. This has now been fixed. |
TTSD-50532, TTSD-50547, TTSD-50868 |
Modeling |
In Tekla Structures 2022, bolt holes were not shown correctly in model views in some cases. There was an issue with XS_DRAW_BOLTS_3D_IN_BOLT_LAYER set to TRUE and, for example, when bolt holes were created through both flanges of an I beam. This issue has now been fixed. |
TTSD-48624 |
Tools and components |
Previously, in some rare cases, Tekla Structures could behave incorrectly or stop working unexpectedly when plugin components were moved or copied. This has now been fixed. |
TTSD-44588 |
Numbering |
The Change part number ribbon command can now be used to change the position number of rebar set bars. The Select single rebars or Select rebar groups selection switch should be used to select the bars required. The Select rebar sets switch cannot be used with the command, because a rebar set may contain bars with many different position numbers. |
TTSD-47301 |
Numbering |
The "Numbering is not up to date" message did not appear when you were opening a single-part drawing that was previously created, it was missing since Tekla Structures 2021. Now the message appears as expected. |
TTSD-48706 |
Numbering |
Previously, some component objects ended up in a wrong assembly after copying. This has now been fixed. |
TSAC-5193 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): The export of the reinforcement from rebar assemblies is now supported. Rebar assemblies of the types Mesh, Bent mesh and Roll mat are collected and exported as mesh. The rebar assembly type is defined in rebar assembly properties. If the rebar assembly type is undefined or Cage, the rebar assemblies are exported as cages. Rebar assemblies of the type Braced girder are exported as braced girders, and those of the type Embed are exported as mountparts. As the cage is not supported in Unitechnik versions below 6.1.0., the cage rebars will be exported as loose. |
TSAC-6160 |
Import, export, interoperability (concrete) |
Export Unitechnik (79): Previously, some symbol definition file settings caused the symbol to be offset from the correct location. This issue has now been fixed. |
TSAC-6427 |
Import, export, interoperability (concrete) |
Export ELiPLAN file (68): Previously, border lines were exported unnecessarily. This issue has now been fixed. |
TSAC-6430, TSAC-5756 |
Import, export, interoperability (concrete) |
Export ELiPLAN file (68): Previously, net area was sometimes exported as a negative value, or was exported incorrectly for some elements with certain types of cuts or recesses. These issues have now been fixed. |