2021 SP2: 새로운 기능 및 개선 사항

Tekla Structures
2021
Tekla Structures

2021 SP2: 새로운 기능 및 개선 사항

Tekla Structures 2021 SP2에는 유용한 새 기능과 개선 사항이 여러 가지 포함되어 있습니다.

도면에서 비 실선 표시 개선

이전에는 도면에서 중복되는 비 실선(파선, 점쇄선 등)이 잘못 정렬되어 실선으로 보였습니다. 그러면 숨겨진 객체가 숨겨지지 않은 것으로 나타나 심각한 문제가 발생합니다(특히 콘크리트 도면 관련). 현재 수정되었습니다.

TTSD-19926

길어진 IFC2x3 내보내기 출력 파일 경로

출력 파일 경로 문자 수 제한이 72자에서 247자로 늘어났습니다.

TTSD-32135

Export Unitechnik (79)

  • 여러 단어를 포함한 문자열로 구성된 객체 이름에 대한 따옴표

    이제 따옴표를 사용하여 여러 단어를 공백으로 구분한 문자열로 구성된 객체 이름을 지정할 수 있습니다. 이는 임베디드 탭의 임베드 옵션과 같은 내보내기 설정 내의 모든 이름 목록 필드에서 수행할 수 있습니다. 

    TSAC-5345

  • 외부 정의 파일 - 내보낸 철근을 제어하는 새로운 방법

    외부 정의 파일을 사용하여 유형 및 명칭 정보를 덮어쓸 수 있습니다. 이는 일반적으로 모델 객체를 통해 자동으로 결정됩니다. 철근 데이터 탭에서 철근 정의 파일을 지정할 수 있습니다. 정의 파일은 .csv 파일이며 구조가 고정되어 있습니다.

    TSAC-5475

Export ELiPLAN file (68): 단위 변환에 대한 새 UDA

이제 데이터 설정 탭에서 단위 변환에 대한 UDA를 지정할 수 있습니다. 이 UDA에 유효한 단위가 지정되면 기본 단위나 변환 파일에 정의된 단위 대신 단위 변환에 사용됩니다.

TSAC-5475

Tekla Structures 확장 프로그램 관리자 개선 사항

Tekla Structures 확장 프로그램 관리자에서 이제 확장 프로그램을 다음 유형별로 나열할 수 있습니다. 확장 또는 환경. 이제 이름, 만든 이, 설명 및 확장 유형을 기준으로 콘텐츠를 검색할 수도 있습니다.

이제 날짜별 확장 프로그램 분류에서 시스템 로컬의 날짜 형식을 정확하게 반영합니다.

TTSD-25796

새로운 철골 컴포넌트

Tekla Structures 2021 SP2에서 다음과 같은 새로운 철골 접합 컴포넌트를 도입합니다.

  • Wooden purlin shoe (15)는 철골 보와 목재 퍼린 사이에 접합을 생성합니다. 퍼린 슈는 목재 퍼린이 장착되는 철골 보에 용접됩니다. 다양한 프로파일을 사용하여 퍼린 슈(예: U자형 및 L자형 프로파일)를 생성할 수 있습니다.

    TSAC-5187

  • Simple bolt connection (5)은 두 철골 프로파일 사이에 볼트 체결 접합을 생성합니다.

    TSAC-5186

  • Windbracing 2 (16)는 접합 플레이트, 나사형 로드 및 너트를 사용하여 단일 할로우 브레이스를 보나 기둥에 접합합니다. 원형 플레이트는 접합 플레이트에 용접되고 접합 플레이트는 보나 기둥에 볼트 체결됩니다.

    TSAC-5188

철근 커플러 및 앵커 도구 개선 사항

Tekla Structures 2021 SP2에서 철근 커플러와 앵커 도구가 크게 개선되었습니다.

새 번호 시리즈 옵션

철근 커플러, 철근 단부 앵커철근 분할 및 추가 커플러가 변경되어 매개변수 탭에 다음과 같이 커플러 부재 및 어셈블리 넘버링 설정(접두사 및 시작 번호)에 새로운 다음에서 상속 옵션이 생겼습니다.

  • 없음

    도구는 이전과 동일하게 작동하며 부재/어셈블리 번호 시리즈는 대화 상자에서 정의된 것입니다.

  • 철근

    번호 시리즈 값은 기본 철근 번호 시리즈에서 가져옵니다.

  • 콘크리트 부재

    번호 시리즈 값은 기본 철근 콘크리트 부재의 콘크리트 부재 번호 시리즈에서 가져옵니다.

TSAC-5098

커플러 및 단부 앵커의 UDA

이제 철근 커플러, 철근 단부 앵커철근 분할 및 추가 커플러에 새로운 커플러 속성 탭이 생겨 커플러 또는 단부 앵커 부재의 다양한 UDA 값을 설정할 수 있습니다. 각 UDA에 대해 철근 또는 콘크리트 부재에서 값을 상속하도록 선택할 수 있습니다. 아무런 값도 입력하지 않으려면 없음 상속 옵션을 선택합니다.

콘크리트 부재에 해당 UDA에 대한 값이 없는 경우에는 콘크리트 부재의 메인 부재에서 값을 가져옵니다. 기본적으로 커플러 속성 탭에서 사용자 필드 1 … 4 UDA 값과 설명을 입력할 수 있습니다.

RebarCouplers.Udas.dat 파일에서 UDA 필드를 수정하여 UDA 집합을 사용자 지정할 수 있습니다. ..\Environments\common\system에서 RebarCoupler.Udas.dat의 예를 찾을 수 있습니다.

TSAC-4557

철근 커플러 생성 개선 사항

철근 커플러가 변경되어 철근 단부 간 실제 간격이 커플러의 길이보다 큰 경우에도 항상 커플러가 생성됩니다. 실제 여유 공간이 커플러 길이보다 큰 경우 상태 표시줄에 추가 경고 메시지가 표시됩니다. 커플러 길이는 대화 상자에 지정된 길이이며 사용자 지정 부재 커플러의 경우에는 사용자 지정 부재의 물리적 최대 길이입니다. 이전에는 발생 가능한 오류 상황을 나타내기 위해 잘못된 커플러 부재만 생성되었습니다.

TSAC-5176

사용성 개선 사항

철근 커플러 및 앵커 도구에서 다음과 같은 여러 가지 유용성이 개선되었습니다.

  • 이제 철근 분할 및 추가 커플러 컴포넌트를 통해 철근 그룹과 유사하게 철근 집합을 분할할 수 있습니다.

    TSAC-2648

  • 철근 집합을 사용하여 철근 커플러 및 단부 앵커 생성 시 이제 선 미리보기가 표시되어 컴포넌트를 생성할 위치를 더욱 잘 보여줍니다.

    TSAC-5374

  • 철근 단부 앵커가 이제 유효한 앵커와 구분하기 위해 큐브로 유효하지 않은 단부 앵커를 생성합니다.

    TSAC-5075

철근 형상 관리자: 기존 형상과 선택한 철근을 비교

이제 철근 형상 관리자에서 RebarShapeRules.xml 파일의 기존 굽힘 형상과 모델에서 선택한 철근을 비교할 수 있습니다. 다음을 수행합니다.

  1. 모델에서 철근을 선택합니다.

  2. 파일 메뉴에서 편집기 > 철근 형상 관리자를 클릭합니다.

    철근 형상 관리자 대화 상자가 열립니다.

  3. 모델 철근 목록에서 비교하려는 철근 형상을 선택합니다.

    모델에서 다른 철근을 선택해야 하는 경우에는 먼저 선택한 항목 가져오기 버튼을 클릭합니다.

  4. 형상 카탈로그 목록에서 기존 굽힘 형상을 선택합니다.

  5. 형상 카탈로그 목록에서 선택한 항목 비교 버튼을 클릭하여 기존 형상과 선택한 형상을 비교합니다.

굽힘 형상 규칙 목록에서 통과된 규칙은 녹색으로 표시되고 실패한 규칙은 빨간색으로 표시됩니다. 형상 간에 불일치하는 다른 이유가 있을 경우 추가 경고 대화 상자가 표시됩니다.

필요한 경우, 모델의 철근 형상이나 철근 형상 관리자의 굽힘 형상 규칙을 수정할 수 있습니다.

TSAC-4568

수정

결함 번호 개발 영역 설명
TSAC-1830 Concrete components

Wall layout opening: Previously, loading filler part properties from a file and then applying them did not work properly if the file contained some special characters (non-English characters). This has now been fixed.

TSAC-4224 Concrete components

Wall layout opening: The minimum size of the openings that can be created has been lowered. Originally, the size was 50 x 50 mm for square openings and 50 mm for the radius of circular openings. Now the size has been lowered to 10 x10 mm and 10 mm for the radius of circular openings.

TSAC-5258 Concrete components Reinforced concrete stair (95): End condition settings for the rebars created on the Bar H tab are no longer applied when they are hidden as not to be used for particular rebar shapes.
TSAC-5071 Concrete components

Rebar coupler and Rebar end anchor components have been modified so that they now clear all rebar UDA values if the coupler or end anchor is not valid. 

TSAC-5240 Concrete components Reinforcement mesh array (91): Integers are now used for mesh sizes when calculating the overlapping of the meshes. This means that instead of shortening the mesh to 0.99, the mesh size is rounded up to a full mesh and the overlapping is increased.
TSAC-5070 Concrete components

Rebar coupler, Rebar end anchor: Previously, the components did not use the custom component input option value controlled by Use auto attribute file. This has now been fixed. Changing the input point option in the component property dialog box with Use manually entered values worked correctly.

TSAC-4066 Concrete components

Wall layout T connector: Previously, the gap between the parts of the first layer was created twice the size of the value defined in the Free space option in the Wall layout T connector dialog box. This has now been fixed.

TSAC-5073 Concrete components

Rebar coupler: When creating a rebar coupler, Tekla Structures now checks the splitter overlap and shows a warning if it is not zero (or less). Status bar instructions for creating the component have also been improved and a warning is now also shown if the input is not valid, for example, if you select a part. 

TSAC-3817, TSAC-3021 Concrete components

Wall layout: Wall panel geometry is now created properly also when an opening is located at the exterior edges and corners.

TSAC-5529 Concrete components

Embedded anchors (8): Previously, creating certain geometries on the Thickening tab could cause a crash. This has now been fixed.

TSAC-5488 Concrete components

Wall layout: Geometry calculation has been changed to properly handle situations where the opening goes outside the original exterior perimeter.

TSAC-5465 Concrete components Mesh bars: The Cut bars by negative neighbor parts option on the Bar end conditions tab has been improved. The detection of the neighbor negative parts for bars cut by the opening has been fixed.
TSAC-1340 Concrete components

Rebar end anchor: The status bar instructions for applying rebar end anchors to rebar set ends have been improved.

TSAC-5364 Steel components

Web stiffeners (1060): Previously, when creating only an above line weld or a below line weld, both welds were always created. This has now been fixed.

TSAC-5108 Steel components Pipe column and beam panel zone (21): The short column name is now taken from the main part name by default.
TSAC-2651 Steel components U.S. Base plate (1047): It is now possible to set the Gage material UDA for the leveling plate on the Parts tab.
TSAC-5500 Steel components

Stiffened end plate (27), Partial stiff end plate (65): Previously, holes in the end plate were created with incorrect rotation in some cases. This has now been fixed.

TSAC-5022 Steel components

Cold rolled overlap (1): Previously, the component worked incorrectly for user-defined Z profile secondary parts. This has now been fixed.

TSAC-5443 Steel components

Two sided end plate (143): Previously, the bolt gage was incorrectly applied in the component in some situations. This has now been fixed.

TSAC-5457 Steel components

Simple clip angle (31): Previously, the bolt extra length was not correct if the bolts were used with a U profile as the secondary part. This has now been fixed.

TSAC-5463 Steel components

Shear plate simple (146): Previously, the distance between the bolts and the secondary beam edge was not correct. This has now been fixed.

TSAC-5391 Steel components

Bolted moment connection (134): Previously, when the secondary part was sloped and the shear tab was set to be created parallel with the main part, the shear tab was not created. This has now been fixed.

TSAC-5131 Steel components

Purlin connections (11): Previously, bolts were sometimes created on the opposite side of the secondary beam. This has now been fixed.

TSAC-5146 Steel components

Base plate (1042): Previously, the cast plate did not follow the offset of the base plate. This has now been fixed.

TSAC-5386 Steel components

Bolted gusset (11): Previously, when using a twin profile as the secondary part, only one member of the twin profile was welded to the gusset. This has now been fixed and both members of the twin profile are welded.

TSAC-5159 Steel components

Welded beam to beam (123): Previously, the secondary part bottom flange was not cut correctly. This has now been fixed.

TSAC-5491 Steel components Two sided end plate (142): Previously, unwanted bolts were created in some situations. This has now been fixed.
TSAC-5308 Steel components Tube gusset (20): Previously, assembly numbering of the gusset plate was not correctly set when the component was used to create a connection to an I profile main part.
TSAC-5109 Steel components Pipe column and beam panel zone (21): By default, the appropriate diaphragm thickness is now calculated taking into account all beam flange thicknesses and the level position.
TSAC-5432 Steel components

Joining plates (14): Previously, different selection order of parts caused the component to work differently. This has now been fixed.

TSAC-5307 Steel components

Bolted moment connection (134): Previously, when the flange plates were wider than the column, they were created incorrectly. This has now been fixed.

TTSD-44481 Organizer

Previously, Organizer synchronization could fail in case an assembly had lost its main part. This has now been fixed.

TTSD-44583 Organizer

Previously, Organizer data was corrupted in a Tekla Model Sharing model if the assembly of a part was missing. This has now been fixed.

TTSD-45387 Import, export, interoperability

The advanced option XS_DISABLE_CIS2 has been removed from the Advanced Options dialog box. This advanced option is an old option that does not work anymore.

TTSD-44504 Import, export, interoperability

IFC object conversion: Now the conversion supports the copying of the object type (IfcRelDefinesByType) property set property to UDA.

TTSD-44041 Import, export, interoperability Export drawings to DWG/DXF: If the advanced option XS_DWG_EXPORT_3D_MODEL_COORDINATES was set to TRUE, the template was displayed in the model space instead of the paper space. This has now been fixed.
TTSD-44678 Import, export, interoperability

IFC2x3 export: The export did not export the object location correctly with edge chamfer offsets. This has now been fixed.

TTSD-44418 Import, export, interoperability

The profile conversion files used in import and export between Tekla Structures and Tekla Structural Designer have been fixed. Each conversion file line now contains one profile entry with the neutral file profile name, the # symbol and the profile code, and then the equal sign (=) followed by the Tekla Structures profile name.
For example: STB 229x305x70#00610=TEE229*305*70
Note that you may need help from your local Tekla support with the conversion files.

Also, several errors in the conversion for US metric profile names have now been fixed.

TTSD-23135 Import, export, interoperability

Previously, importing attributes by object GUID did not import attributes for bolts, welds and rebars. This has now been fixed.

TTSD-43777 Import, export, interoperability

IFC2x3 export: The z level failed in the export in Tekla Structures 2021 if the base point local z coordinate was used. This has now been fixed.

TTSD-43959 Import, export, interoperability

When transferring design intent reinforcement for Tekla Structural Designer walls with multiple zones, starter bars are now created into the foundation depth. Tekla Structural Designer 2021 SP2 or later is required.

TTSD-37633 Import, export, interoperability The view size property Fit by parts no longer shows un-cut solids.
TTSD-42577 Import, export, interoperability

Non-rectangular wall panels are now imported from Tekla Structural Designer to Tekla Structures as rectangular walls with a height equal to the enclosing rectangular shape. Previously, non-rectangular wall panels caused an error, which resulted in the failure to import any of the model.

TTSD-44467, TTSD-44858 Import, export, interoperability

In the Tekla Structural Designer Import dialog box under Rebars > Creation options, the Simplify bars check box is no longer selected by default. 
If you select the Simplify bars check box, the following warning message is displayed:
'Design information linked to end detail modifiers (hooks) and splitters (laps, cranks) will not be imported'
The message will disappear when you clear the Simplify bars check box.

TTSD-44983 Import, export, interoperability

IFC object conversion: The IFC B-rep to extrusion object conversion sometimes created beams to bottom of the object and location failed. This has now been fixed.

TTSD-35277 Import, export, interoperability

Export drawings to DWG/DXF: The drawing export now supports loading settings with a macro.

TTSD-44982 Import, export, interoperability

IFC object conversion: The failing column handle offset in the B-rep to extrusion conversion has been fixed.

TTSD-44032 Import, export, interoperability Export drawings to DWG/DXF: An application error occurred when you loaded settings in the Export drawings to DWG/DXF dialog box. This has now been fixed.
TTSD-44739 Import, export, interoperability

In the Tekla Structural Designer Import dialog box, the Single bars only check box has been removed from Rebars > Creation options as it was not used in the import.

TTSD-44639 Import, export, interoperability

IFC object conversion: The IFC object conversion now converts solid model presentation objects.

TTSD-45287 Import, export, interoperability

IFC4 export: The IFC4 export file name with a dot removed the rest of the file name. This has now been fixed.

TTSD-44413 Import, export, interoperability

Trimble Connector: When you upload your model to the linked Trimble Connect project as a .tekla model, the export can now read profile information (profitab.inp file) from XS_PROJECT and XS_FIRM folders.

TTSD-44628 Import, export, interoperability

IFC4 export: Sometimes exporting objects with a certain chamfer caused a Tekla Structures application error. This has now been fixed.

TTSD-44725 Import, export, interoperability

Some HP profiles, hollow sections and pipes were not included in the standard profile conversion, resulting in "Missing profiles detected" messages when imported from Tekla Structural Designer for US Imperial and US Metric models.

TPLED-201 Templates and reports

Template Editor: Editing the font color of multiple text objects worked only the first time the font color was changed. This has now been fixed.

TPLED-200 Templates and reports

Template Editor:

The following issues have now been fixed:
- Previously, if a template contained a rule-defined picture object, Template Editor still prompted for unsaved changes after the template had been saved. 
- Previously, after saving the template with a new name, the new template file name was not updated to the title bar of Template Editor.

TTSD-28819 Templates and reports Tapered rebar pull-out dimensions were incorrect in the PDF report output. This has now been fixed.
TTSD-44152 Templates and reports

Missing definitions in pull-out height and width parameters in templates could cause Tekla Structures to crash. This has now been fixed.

TTSD-44409 Templates and reports

When an xls report was created and opened in Microsoft Excel, Microsoft Excel could freeze if the report contained references to image files with long paths. The reason was that the valuefield content was longer that the length specified for it, and therefore the path to the image file was cut. This has now been fixed so that if the valuefield content starts with the text '<IMG' and ends with the character '>', the path is not cut.
If the above case is discovered during template output, a warning message is written to the log indicating the maximum length and the path to the template file.

TTSD-43450 Drawings

Document manager: Exceptions occurred when you rapidly toggled data cell values by editing those directly in columns that you sorted. This has now been fixed.

TTSD-44644 Drawings

Printing: The Print on multiple sheets option was not working correctly. This has now been fixed.

TTSD-38039 Drawings

Grid dimensions did not work correctly if a drawing filter was applied. This has now been fixed.

TTSD-43250 Drawings

Part center line associations that were saved incorrectly in some cases are now saved correctly.

TTSD-41773 Drawings

Reflected views now work correctly in drawings.

TTSD-38134 Drawings

The positioning of the level mark base points in drawing update has been improved. Holding down Shift and dragging the level mark away from the part keeps the valid associativity data (just like when you use the Move linear command).

TTSD-44476 Drawings

Previously in some cases, reflected views in drawings could cause a Tekla Structures application error. For example, this may have happened when you adjusted the drawing view depth, and had set the Reflected view setting to Yes. This has now been fixed.

TTSD-26968 Drawings

Reference object hidden lines were displayed in drawings even though they were disabled when the line type and color of the lines matched the properties of the visible lines. This has now been fixed.

TTSD-43906 Drawings

Level marks are now placed correctly when a part has been modified. A zero level mark no longer gets a change cloud if only the sign (+ or -) changes.

TSAC-4236 Drawings Rebar pull-out picture and marking: The usage of the rebar_config.inp file settings in Rebar pull-out picture and marking application has been improved. Now, settings like ScheduleDimensionRoundingAccuracy and PullOutShowDuplicateDim are taken correctly from rebar_config.inp.
Note that some of the settings in the rebar_config.inp file might be overwritten when Rounding settings on the Dimensions tab is set to By users setting.
TTSD-42531 Drawings

Snapping to center lines now works identically in drawing and modeling modes: Center lines are snapped to when the Snap to geometry lines/points switch is enabled. Center lines are no longer snapped to in drawings when the Snap to reference lines/points switch is enabled.

TTSD-39486 Drawings Internal view coordinates were sometimes corrupted, which caused wrong placing of the drawing views. This has now been fixed.
TTSD-43854 Drawings

Sometimes, the part to grid dimensioning in GA drawings did not work correctly. This has now been fixed.

TTSD-44330 Drawings Tiny dimension rule associativity lists are no longer displayed if associativity rules are not found for dimension points.
TTSD-44973 Drawings

More DWG files are now supported in drawings when adding them as extra objects.

TTSD-13610 Tekla Model Sharing

Previously, you sometimes could not reserve the next write out directly after joining a model, but had to read in a packet first. This has now been fixed.

TSAC-4885 Reinforcement

In Rebar shape manager, the unknown rebar shapes are now read from the first RebarShapeRules.xml file, following the same reading order as the other, recognized shapes. Previously, the unknown rebar shapes were read from the last RebarShapeRules.xml file.
Note that if you modify the rebar shapes and then save the rebar shape definitions to the model folder, you need to reopen the model to apply the changes.

TTSD-44717 Reinforcement

Rebar sets: Sometimes, when using rather big concrete covers, some bars were incorrectly shortened around holes. This has now been fixed.

TSAC-4571 Reinforcement

In Rebar shape manager, two new built-in geometrical properties are now available for circular arc legs:

  • Arc width (AW)
  • Arc height (AH)
TTSD-42373 Reinforcement Rebar splice: In some cases, rebar splices could not be selected when the Select rebar sets selection switch was active. This has now been fixed.
TTSD-44455 Reinforcement Rebar sets: Sometimes when you dragged a rebar set guideline or modifier, its line handle was left in the original location. This has now been fixed.
TSAC-5211 Reinforcement

In Rebar shape manager, the value of the REVERSED property is now calculated correctly for curved bars.

TTSD-39155 Reinforcement

Rebar groups have the following three issues fixed:

  • Rebar group bars in a tapered rebar group with non-planar bar geometry were in some cases incorrectly offset from input points. This has now been fixed not to occur when creating new rebar groups. To get existing rebar group offsets fixed, you need to modify them.
  • Tapered rebar groups which have exact spacings as the creation method and spacings defined so that there are too many bars compared to the group length were incorrectly handled in mirroring. This has now been fixed.
  • The mirroring of tapered rebar groups containing non-parallel straight bars has now been fixed.
TTSD-43922 Reinforcement

Rebar sets: For some rebar sets, a value below 2 for the Minimum number of bars in similar group UDA could cause a crash. This has now been fixed.

TSAC-5212 Reinforcement

In Rebar shape manager, the value of the Arc length (AL) property is now calculated more accurately for curved bars, regardless of the modeling direction.

TTSD-43341 Reinforcement

Previously, rebar set modifiers sometimes became visible when you modified the part the rebar set bars were attached to. This has now been fixed.

TTSD-44842 Reinforcement

Multi-user: Previously, modifying and saving drawings in multi-user models could sometimes detach rebars from their parent parts and flag their numbering as out-of-date. This has now been fixed.

TSAC-5515 Reinforcement

In Rebar shape manager, the curved bar arc length and angle were not correctly reported when the bar had hooks and the advanced option XS_REBAR_RECOGNITION_HOOKS_CONSIDERATION was set to FALSE. This has now been fixed.
 

TTSD-44114 Modeling Batch editor now handles better the cases where a component has created the whole assembly.
TTSD-45156 Modeling

In the US environment, shape names that only consisted of numerical characters were unintentionally converted to imperial units. This affected filtering in the Object Group dialog box and labels in the 3D views. This has now been fixed.

TTSD-44693 Modeling

Previously, the workplane changed to model origin if you typed the values, for example, when you extended a beam. This has now been fixed.

TTSD-43838 Modeling

Sometimes perpendicular snapping happened to an unrelated, distant point. This has now been fixed.

TTSD-21254 Modeling

Previously, autosave files were deleted without a new save being successful. This has now been fixed.

TTSD-44069 Modeling

Previously, when the Cut object with line command was used, no ortho symbols were shown irrespective of the cursor position. This now been fixed.

TTSD-45092 Modeling Building hierarchy previously stored sub-assemblies to the floor. This has been changed. Sub-assemblies now inherit the floor from the main assembly.
TTSD-44559 Modeling Batch editor now automatically refreshes the Validation column for newly added targets when they are added.
TTSD-44811 Modeling Previously, using the Split command on plates or slabs allowed to pick points outside the part. This is now prevented, and only points within the part to be split can be picked.
TTSD-44895 Modeling Batch editor now works with corner chamfers.
TTSD-44485 Modeling Batch editor now opens the help when you press F1 on the dialog box.
TTSD-43767 Modeling

If a pour break was created at the border of two separate parts, and one of the parts had a touching opening, the pour break might fail. This has now been improved.

TTSD-44558 Modeling Batch editor dialog box now by default resizes its size in horizontal direction based on the amount of columns.
TTSD-44825, TTSD-44490 Modeling

Previously, when creating bent plates using any component child parts, the bent plate creation did not succeed and the original parts were deleted. This has now been fixed.

TTSD-44731 Modeling Batch editor works now more reliably in cases where properties need to be copied from components to exploded targets.
TTSD-44489 Modeling Previously, when selecting a part to be split, grid got priority for the selection even if the Select grid selection switch was off. This has now been fixed, and parts are preferred over grids.
 
TTSD-15650 Modeling

Multi-user: In some cases, numbering old standard part models could cause Tekla Structures to crash. This has now been fixed.

TTSD-45523 Modeling

Previously, Move/Copy point or part handle command switched the coordinate system to model origin. This has now been fixed.

TTSD-44730 Modeling Previously, Batch editor might crash when copying from exploded source to targets generated by components. This has now been fixed.
TTSD-44674 Modeling Previously, the Split command sometimes split the wrong object if there were several nearby objects that were overlapping, touching, or otherwise close. This has now been fixed.
TTSD-44110 Modeling Batch editor:
Previously, copying from a component assembly to an assembly with an exploded component resulted in extra parts. This has now been fixed.
Previously, copying an assembly inside a component did not copy anything. This has now been fixed.
TTSD-41620 Modeling In some situations, Tekla Structures could crash when saving or autosaving the model. This has now been fixed.
TTSD-44240 Modeling Previously, coloring of some objects was not correct if you changed the value of the XS_USE_INTEGRATED_BUILDING_HIERARCHIES advanced option. This has now been fixed.
TTSD-42041 Modeling

If XS_ENABLE_POUR_MANAGEMENT is switched to FALSE in a model with cast-in-place concrete parts that form pours, you can now use the Diagnose & repair model commands to remove the obsolete pours from the model. Previously it was not possible to remove them, even by deleting the parts that formed the pours.

SOLD-1674 Licensing

Tekla Model Sharing licenses are now released properly again when you close Tekla Structures.

TTSD-43328 Core The object database cleanup after object deletion has been improved.
TTSD-43403 Core

Sometimes Tekla Structures could crash at startup. This has now been fixed.

TTSD-44427 Core

Previously, Tekla Structures crashed when the bolt visibility was set to Exact in 3d views. This has now been fixed.

TTSD-44980 Core Previously, Tekla Structures could crash when saving. This happened when the model folder had files with unsupported unicode names. This has now been fixed.
TTSD-44194 Core Previously, some large solids could cause memory buffer overruns. This has now been fixed.
TTSD-41874 Tools and components Array of objects (29): The limitation of maximum 256 copies has been removed. 
TTSD-42333 Tools and components In some cases, when modifying custom component parameters, if you wanted to undo the modification, you had to perform the undo command twice. This has now been fixed.
TTSD-45032 Tools and components Applications & components catalog: Hiding predefined groups, such as Ungrouped items, in the catalog is not possible anymore.
TTSD-35472 Tools and components

Applications & components catalog: It is now possible to generate a troubleshooting dump file that shows all the data used to construct the selected component or group in the Applications & components catalog. The file is by default stored in the model's \local\temp folder.

To activate the file generation command, first click the Access advanced features button > Catalog management > Show dump command for selected component or group. Then select the component or group in the catalog, right-click and select the Dump troubleshooting data command. In the dialog box that opens, you can change the target file path and file name. Click Save to save the file.

TSAC-5363 Tools and components

Previously, the Applications & components catalog could be empty when the Windows regional setting Beta: Use Unicode UTF-8 for worldwide language support was selected. This has now been fixed. Note that it is not recommended to use this setting with Tekla Structures.

TTSD-43422 Tools and components Previously, when custom components that contained plugins were imported, an error dialog box was shown and a failure message was written to the log. This does not happen anymore.
TTSD-45196 Numbering

If you cancelled the save-numbering-save operation, Tekla Structures might sometimes crash. This has now been fixed.

TTSD-43674 User interface The Define custom component command now has a scalable vector icon available.
TTSD-38333 User interface

Previously, in some rare cases, there was an error in the property pane about object reference not set to an instance of an object. This has now been fixed.

TTSD-44683 Import, export, interoperability (steel)

NC/DSTV: In certain situations, slotted holes were incorrectly rotated in the exported NC/DSTV files. They were rotated 90 degrees out compared to the actual model orientation, see the image below: 

Image
Slotted holes incorrectly rotated

This happened when the plate width was greater than the plate length, and the advanced option XS_USE_NEW_PLATE_DESIGNATION was set to TRUE or to FOR_STEEL_PARTS_ONLY. This has now been fixed.

TSAC-5390 Import, export, interoperability (concrete) Export Unitechnik (79): You can now export also cut parts using the Opening with a corner symbol setting on the Embeds tab.
TSAC-5400 Import, export, interoperability (concrete) Export Unitechnik (79): Previously, braced girders with alphanumeric rebar sizes caused problems with girder depth position. This has now been fixed. Braced girder rod diameters are now obtained correctly based on the Reinforcing bars diameter setting on the Reinforcement tab.
TSAC-5471 Import, export, interoperability (concrete)

BVBS Export: All bending and arc angles are now rounded to the nearest 0.5 degree. For example, 89.8 degrees will be rounded to 90 degrees.

TSAC-5490 Import, export, interoperability (concrete)

BVBS export: When you select One file per each cast unit and use Assembly template property, the export will now warn if the export results in duplicate file names. The export will still continue.

TSAC-5435 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, the UT_REBAR_TYPE UDA was not read for rebar sets. This has now been fixed.

TSAC-5543 Import, export, interoperability (concrete)

BVBS Export: The file naming template by [Assembly template] now works with the PROJECT.NUMBER property.

TSAC-4953 Import, export, interoperability (concrete) Export Unitechnik (79): A new option has been added to the Auto-rotate on pallet list on the TS configuration tab. When the Auto-rotate on pallet option is selected, the element is rotated based on the fixed set of rules defining that the longer edge with no cuts or protruding embeds is at the bottom edge of the pallet. For the Auto-rotate on pallet option, you can also select if the default rotation direction is To long even edge (clockwise) or To long even edge (counterclockwise).
TSAC-5410 Import, export, interoperability (concrete)

Export ELiPLAN file (68): The data conversion file now supports the wildcard "*" in regular expressions in the first column for finding strings from Tekla Structures objects.

TSAC-5484 Import, export, interoperability (concrete)

Export ELiPLAN file (68): You can now specify the material code using the new setting, Material code, on the Data content tab. The options are Name, Assembly prefix, Material, Profile, UDA, Text[TEMPLATE], and Template.

도움이 되었습니까?
이전
다음