2020 SP9: 새로운 기능 및 개선 사항

Tekla Structures
2020
Tekla Structures

2020 SP9: 새로운 기능 및 개선 사항

신규 Trimble Identity 지원

이 서비스 팩으로 Tekla Structures가 새롭게 향상된 Trimble Identity와 호환됩니다. 이 업데이트를 통해 로그인이 필요한 기능을 계속 사용할 수 있습니다.

Trimble Identity 개선 사항에 대한 자세한 정보는 Tekla 제품 및 서비스 로그인 변경 내용을 참조하십시오. 이러한 변경 사항의 타임 라인이 있는 Tekla Structures 특정 정보는 Tekla Structures 로그인 변경 내용을 참조하십시오.

COG 치수의 새 기호 선택

이제 기호 옵션에서 COG 기호를 변경할 수 있습니다. 이를 위해 기호 번호에서 선택을 클릭하고 다른 기호를 선택합니다.

TEX-8841

Export ELiPLAN file (68): 단위 변환에 대한 새 UDA

이제 데이터 설정 탭에서 단위 변환에 대한 UDA를 지정할 수 있습니다. 이 UDA에 유효한 단위가 지정되면 기본 단위나 변환 파일에 정의된 단위 대신 단위 변환에 사용됩니다.

TSAC-5475

Tekla Structures 확장 프로그램 관리자 개선 사항

Tekla Structures 확장 프로그램 관리자에서 이제 확장 프로그램을 다음 유형별로 나열할 수 있습니다. 확장 또는 환경. 이제 이름, 만든 이, 설명 및 확장 유형을 기준으로 콘텐츠를 검색할 수도 있습니다.

이제 날짜별 확장 프로그램 분류에서 시스템 로컬의 날짜 형식을 정확하게 반영합니다.

TTSD-25796

새로운 철골 컴포넌트

다음과 같은 새로운 철골 접합 컴포넌트가 Tekla Structures 2020 SP9에 포함됩니다.

  • Wooden purlin shoe (15)는 철골 보와 목재 퍼린 사이에 접합을 생성합니다. 퍼린 슈는 목재 퍼린이 장착되는 철골 보에 용접됩니다. 다양한 프로파일을 사용하여 퍼린 슈(예: U자형 및 L자형 프로파일)를 생성할 수 있습니다.

    TSAC-5187

  • Simple bolt connection (5)은 두 철골 프로파일 사이에 볼트 체결 접합을 생성합니다.

    TSAC-5186

  • Windbracing 2 (16)는 접합 플레이트, 나사형 로드 및 너트를 사용하여 단일 할로우 브레이스를 보나 기둥에 접합합니다. 원형 플레이트는 접합 플레이트에 용접되고 접합 플레이트는 보나 기둥에 볼트 체결됩니다.

    TSAC-5188

샌드위치 및 이중 벽체 개선 사항

이제 UDA 탭에서 사용자가 정의하는 각 사용자 정의 속성(UDA)에 대해 셸을 선택할 수 있습니다. 이렇게 하면 필요한 경우 특정 셸에 대해 UDA를 더 많이 설정할 수 있습니다.

TSAC-5406

철근 커플러 및 앵커 도구 개선 사항

Tekla Structures 2020 SP9에서 철근 커플러와 앵커 도구가 크게 개선되었습니다.

새 번호 시리즈 옵션

철근 커플러, 철근 단부 앵커철근 분할 및 추가 커플러가 변경되어 매개변수 탭에 다음과 같이 커플러 부재 및 어셈블리 넘버링 설정(접두사 및 시작 번호)에 새로운 다음에서 상속 옵션이 생겼습니다.

  • 없음

    도구는 이전과 동일하게 작동하며 부재/어셈블리 번호 시리즈는 대화 상자에서 정의된 것입니다.

  • 철근

    번호 시리즈 값은 기본 철근 번호 시리즈에서 가져옵니다.

  • 콘크리트 부재

    번호 시리즈 값은 기본 철근 콘크리트 부재의 콘크리트 부재 번호 시리즈에서 가져옵니다.

TSAC-5098

커플러 및 단부 앵커의 UDA

이제 철근 커플러, 철근 단부 앵커철근 분할 및 추가 커플러에 새로운 커플러 속성 탭이 생겨 커플러 또는 단부 앵커 부재의 다양한 UDA 값을 설정할 수 있습니다. 각 UDA에 대해 철근 또는 콘크리트 부재에서 값을 상속하도록 선택할 수 있습니다. 아무런 값도 입력하지 않으려면 없음 상속 옵션을 선택합니다.

콘크리트 부재에 해당 UDA에 대한 값이 없는 경우에는 콘크리트 부재의 메인 부재에서 값을 가져옵니다. 기본적으로 커플러 속성 탭에서 사용자 필드 1 … 4 UDA 값과 설명을 입력할 수 있습니다.

RebarCouplers.Udas.dat 파일에서 UDA 필드를 수정하여 UDA 집합을 사용자 지정할 수 있습니다. ..\Environments\common\system에서 RebarCoupler.Udas.dat의 예를 찾을 수 있습니다.

TSAC-4557

철근 커플러 생성 개선 사항

철근 커플러가 변경되어 철근 단부 간 실제 간격이 커플러의 길이보다 큰 경우에도 항상 커플러가 생성됩니다. 실제 여유 공간이 커플러 길이보다 큰 경우 상태 표시줄에 추가 경고 메시지가 표시됩니다. 커플러 길이는 대화 상자에 지정된 길이이며 사용자 지정 부재 커플러의 경우에는 사용자 지정 부재의 물리적 최대 길이입니다. 이전에는 발생 가능한 오류 상황을 나타내기 위해 잘못된 커플러 부재만 생성되었습니다.

TSAC-5176

사용성 개선 사항

철근 커플러 및 앵커 도구에서 다음과 같은 여러 가지 유용성이 개선되었습니다.

  • 이제 철근 분할 및 추가 커플러 컴포넌트를 통해 철근 그룹과 유사하게 철근 집합을 분할할 수 있습니다.

    TSAC-2648

  • 철근 집합을 사용하여 철근 커플러 및 단부 앵커 생성 시 이제 선 미리보기가 표시되어 컴포넌트를 생성할 위치를 더욱 잘 보여줍니다.

    TSAC-5374

  • 철근 단부 앵커가 이제 유효한 앵커와 구분하기 위해 큐브로 유효하지 않은 단부 앵커를 생성합니다.

    TSAC-5075

철근 형상 관리자: 기존 형상과 선택한 철근을 비교

이제 철근 형상 관리자에서 RebarShapeRules.xml 파일의 기존 굽힘 형상과 모델에서 선택한 철근을 비교할 수 있습니다. 다음을 수행합니다.

  1. 모델에서 철근을 선택합니다.

  2. 파일 메뉴에서 편집기 > 철근 형상 관리자를 클릭합니다.

    철근 형상 관리자 대화 상자가 열립니다.

  3. 모델 철근 목록에서 비교하려는 철근 형상을 선택합니다.

    모델에서 다른 철근을 선택해야 하는 경우에는 먼저 선택한 항목 가져오기 버튼을 클릭합니다.

  4. 형상 카탈로그 목록에서 기존 굽힘 형상을 선택합니다.

  5. 형상 카탈로그 목록에서 선택한 항목 비교 버튼을 클릭하여 기존 형상과 선택한 형상을 비교합니다.

굽힘 형상 규칙 목록에서 통과된 규칙은 녹색으로 표시되고 실패한 규칙은 빨간색으로 표시됩니다. 형상 간에 불일치하는 다른 이유가 있을 경우 추가 경고 대화 상자가 표시됩니다.

필요한 경우, 모델의 철근 형상이나 철근 형상 관리자의 굽힘 형상 규칙을 수정할 수 있습니다.

TSAC-4568

수정

결함 번호 개발 영역 설명
TSAC-1340 Concrete components

Rebar end anchor: The status bar instructions for applying rebar end anchors to rebar set ends have been improved.

TSAC-3817, TSAC-3021 Concrete components

Wall layout: Wall panel geometry is now created properly also when an opening is located at the exterior edges and corners.

TSAC-4066 Concrete components

Wall layout T connector: Previously, the gap between the parts of the first layer was created twice the size of the value defined in the Free space option in the Wall layout T connector dialog box. This has now been fixed.

TSAC-5070 Concrete components

Rebar coupler, Rebar end anchor: Previously, the components did not use the custom component input option value controlled by Use auto attribute file. This has now been fixed. Changing the input point option in the component property dialog box with Use manually entered values worked correctly.

TSAC-5071 Concrete components

Rebar coupler and Rebar end anchor components have been modified so that they now clear all rebar UDA values if the coupler or end anchor is not valid. 

TSAC-5073 Concrete components

Rebar coupler: When creating a rebar coupler, Tekla Structures now checks the splitter overlap and shows a warning if it is not zero (or less). Status bar instructions for creating the component have also been improved and a warning is now also shown if the input is not valid, for example, if you select a part. 

TSAC-5488 Concrete components

Wall layout: Geometry calculation has been changed to properly handle situations where the opening goes outside the original exterior perimeter.

TSAC-5520 Concrete components

Mesh bars: The length of the bars and their dimensions have been fixed. Previously, Mesh bars could create infinite bars.

TSAC-5529 Concrete components

Embedded anchors (8): Previously, creating certain geometries on the Thickening tab could cause a crash. This has now been fixed.

TSAC-5022 Steel components

Cold rolled overlap (1): Previously, the component worked incorrectly for user-defined Z profile secondary parts. This has now been fixed.

TSAC-5131 Steel components

Purlin connections (11): Previously, bolts were sometimes created on the opposite side of the secondary beam. This has now been fixed.

TSAC-5146 Steel components

Base plate (1042): Previously, the cast plate did not follow the offset of the base plate. This has now been fixed.

TSAC-5159 Steel components

Welded beam to beam (123): Previously, the secondary part bottom flange was not cut correctly. This has now been fixed.

TSAC-5307 Steel components

Bolted moment connection (134): Previously, when the flange plates were wider than the column, they were created incorrectly. This has now been fixed.

TSAC-5364 Steel components

Web stiffeners (1060): Previously, when creating only an above line weld or a below line weld, both welds were always created. This has now been fixed.

TSAC-5386 Steel components

Bolted gusset (11): Previously, when using a twin profile as the secondary part, only one member of the twin profile was welded to the gusset. This has now been fixed and both members of the twin profile are welded.

TSAC-5391 Steel components

Bolted moment connection (134): Previously, when the secondary part was sloped and the shear tab was set to be created parallel with the main part, the shear tab was not created. This has now been fixed.

TSAC-5432 Steel components

Joining plates (14): Previously, different selection order of parts caused the component to work differently. This has now been fixed.

TSAC-5443 Steel components

Two sided end plate (143): Previously, the bolt gage was incorrectly applied in the component in some situations. This has now been fixed.

TSAC-5457 Steel components

Simple clip angle (31): Previously, the bolt extra length was not correct if the bolts were used with a U profile as the secondary part. This has now been fixed.

TSAC-5500 Steel components

Stiffened end plate (27), Partial stiff end plate (65): Previously, holes in the end plate were created with incorrect rotation in some cases. This has now been fixed.

TTSD-44481 Organizer

Previously, Organizer synchronization could fail in case an assembly had lost its main part. This has now been fixed.

TTSD-44583 Organizer

Previously, Organizer data was corrupted in a Tekla Model Sharing model if the assembly of a part was missing. This has now been fixed.

TTSD-23135 Import, export, interoperability

Previously, importing attributes by object GUID did not import attributes for bolts, welds and rebars. This has now been fixed.

TTSD-34490 Import, export, interoperability

IFC2x3 export: The export of rebars failed because of too long spacing value. This has now been fixed, and the Open API Rebar group spacing maximum value has been increased from 99 to 1000.

TTSD-35277 Import, export, interoperability

Export drawings to DWG/DXF: The drawing export now supports loading settings with a macro.

TTSD-43777 Import, export, interoperability

IFC2x3 export: The z level failed in the export in Tekla Structures 2021 if the base point local z coordinate was used. This has now been fixed.

TTSD-44413 Import, export, interoperability

Trimble Connector: When you upload your model to the linked Trimble Connect project as a .tekla model, the export can now read profile information (profitab.inp file) from XS_PROJECT and XS_FIRM folders.

TTSD-44418 Import, export, interoperability

The profile conversion files used in import and export between Tekla Structures and Tekla Structural Designer have been fixed. Each conversion file line now contains one profile entry with the neutral file profile name, the # symbol and the profile code, and then the equal sign (=) followed by the Tekla Structures profile name.
For example: STB 229x305x70#00610=TEE229*305*70
Note that you may need help from your local Tekla support with the conversion files.

Also, several errors in the conversion for US metric profile names have now been fixed.

TTSD-44504 Import, export, interoperability

IFC object conversion: Now the conversion supports the copying of the object type (IfcRelDefinesByType) property set property to UDA.

TTSD-44628 Import, export, interoperability

IFC4 export: Sometimes exporting objects with a certain chamfer caused a Tekla Structures application error. This has now been fixed.

TTSD-44639 Import, export, interoperability

IFC object conversion: The IFC object conversion now converts solid model presentation objects.

TTSD-44678 Import, export, interoperability

IFC2x3 export: The export did not export the object location correctly with edge chamfer offsets. This has now been fixed.

TTSD-44725 Import, export, interoperability

Some HP profiles, hollow sections and pipes were not included in the standard profile conversion, resulting in "Missing profiles detected" messages when imported from Tekla Structural Designer for US Imperial and US Metric models.

TTSD-44982 Import, export, interoperability

IFC object conversion: The failing column handle offset in the B-rep to extrusion conversion has been fixed.

TTSD-44983 Import, export, interoperability

IFC object conversion: The IFC B-rep to extrusion object conversion sometimes created beams to bottom of the object and location failed. This has now been fixed.

TTSD-45287 Import, export, interoperability

IFC4 export: The IFC4 export file name with a dot removed the rest of the file name. This has now been fixed.

TPLED-201 Templates and reports

Template Editor: Editing the font color of multiple text objects worked only the first time the font color was changed. This has now been fixed.

TTSD-44152 Templates and reports

Missing definitions in pull-out height and width parameters in templates could cause Tekla Structures to crash. This has now been fixed.

TTSD-44409 Templates and reports

When an xls report was created and opened in Microsoft Excel, Microsoft Excel could freeze if the report contained references to image files with long paths. The reason was that the valuefield content was longer that the length specified for it, and therefore the path to the image file was cut. This has now been fixed so that if the valuefield content starts with the text '<IMG' and ends with the character '>', the path is not cut.
If the above case is discovered during template output, a warning message is written to the log indicating the maximum length and the path to the template file.

TTSD-26968 Drawings

Reference object hidden lines were displayed in drawings even though they were disabled when the line type and color of the lines matched the properties of the visible lines. This has now been fixed.

TTSD-38039 Drawings

Grid dimensions did not work correctly if a drawing filter was applied. This has now been fixed.

TTSD-38134 Drawings

The positioning of the level mark base points in drawing update has been improved. Holding down Shift and dragging the level mark away from the part keeps the valid associativity data (just like when you use the Move linear command).

TTSD-41773 Drawings

Reflected views now work correctly in drawings.

TTSD-42531 Drawings

Snapping to center lines now works identically in drawing and modeling modes: Center lines are snapped to when the Snap to geometry lines/points switch is enabled. Center lines are no longer snapped to in drawings when the Snap to reference lines/points switch is enabled.

TTSD-43250 Drawings

Part center line associations that were saved incorrectly in some cases are now saved correctly.

TTSD-43450 Drawings

Document manager: Exceptions occurred when you rapidly toggled data cell values by editing those directly in columns that you sorted. This has now been fixed.

TTSD-43854 Drawings

Sometimes, the part to grid dimensioning in GA drawings did not work correctly. This has now been fixed.

TTSD-43906 Drawings

Level marks are now placed correctly when a part has been modified. A zero level mark no longer gets a change cloud if only the sign (+ or -) changes.

TTSD-44718 Drawings

Moving or resizing a drawing view frame no longer causes an application error.

TTSD-44819 Drawings

Changing the view depth in drawings no longer causes a Tekla Structures application error.

TTSD-45004 Drawings

In some cases, resizing drawing view frames could crash Tekla Structures. This has now been fixed.

TTSD-13610 Tekla Model Sharing

Previously, you sometimes could not reserve the next write out directly after joining a model, but had to read in a packet first. This has now been fixed.

TSAC-4571 Reinforcement

In Rebar shape manager, two new built-in geometrical properties are now available for circular arc legs:

  • Arc width (AW)
  • Arc height (AH)
TSAC-4885 Reinforcement

In Rebar shape manager, the unknown rebar shapes are now read from the first RebarShapeRules.xml file, following the same reading order as the other, recognized shapes. Previously, the unknown rebar shapes were read from the last RebarShapeRules.xml file.
Note that if you modify the rebar shapes and then save the rebar shape definitions to the model folder, you need to reopen the model to apply the changes.

TSAC-5211 Reinforcement

In Rebar shape manager, the value of the REVERSED property is now calculated correctly for curved bars.

TSAC-5212 Reinforcement

In Rebar shape manager, the value of the Arc length (AL) property is now calculated more accurately for curved bars, regardless of the modeling direction.

TSAC-5515 Reinforcement

In Rebar shape manager, the curved bar arc length and angle were not correctly reported when the bar had hooks and the advanced option XS_REBAR_RECOGNITION_HOOKS_CONSIDERATION was set to FALSE. This has now been fixed.
 

TTSD-39155 Reinforcement

Rebar groups have the following three issues fixed:

  • Rebar group bars in a tapered rebar group with non-planar bar geometry were in some cases incorrectly offset from input points. This has now been fixed not to occur when creating new rebar groups. To get existing rebar group offsets fixed, you need to modify them.
  • Tapered rebar groups which have exact spacings as the creation method and spacings defined so that there are too many bars compared to the group length were incorrectly handled in mirroring. This has now been fixed.
  • The mirroring of tapered rebar groups containing non-parallel straight bars has now been fixed.
TTSD-43341 Reinforcement

Previously, rebar set modifiers sometimes became visible when you modified the part the rebar set bars were attached to. This has now been fixed.

TTSD-44717 Reinforcement

Rebar sets: Sometimes, when using rather big concrete covers, some bars were incorrectly shortened around holes. This has now been fixed.

TTSD-44842 Reinforcement

Multi-user: Previously, modifying and saving drawings in multi-user models could sometimes detach rebars from their parent parts and flag their numbering as out-of-date. This has now been fixed.

TTSD-15650 Modeling

Multi-user: In some cases, numbering old standard part models could cause Tekla Structures to crash. This has now been fixed.

TTSD-21254 Modeling

Previously, autosave files were deleted without a new save being successful. This has now been fixed.

TTSD-21265 Modeling

There is a new possibility to use separators in the .dat files for the fVF reference function.

  • The fVF reference function can now use a preferred column separator of choice. Previously, it was possible to use only spaces as separators.
  • You can use only a single character as a separator. For example, you cannot use a more complex separator such as "/+/", because only the first character would be considered as a column separator.
  • The .dat file lines do not need to end with a space or separator anymore to retrieve the last element of the column.
  • Columns can now include blank values if the separator is different than the default space separator. For example: =fVF(dat,2,2,"/")

With a data row of 2 / / NG / / 2.5 / / 50 60 50 25/ returns nothing (the empty string when mapped to text).

TTSD-37526 Modeling

If you have the same model open in more than one Tekla Structures session, or if the model was not properly closed, Tekla Structures displays an error message about this situation. This message has now been improved.

TTSD-42041 Modeling

If XS_ENABLE_POUR_MANAGEMENT is switched to FALSE in a model with cast-in-place concrete parts that form pours, you can now use the Diagnose & repair model commands to remove the obsolete pours from the model. Previously it was not possible to remove them, even by deleting the parts that formed the pours.

TTSD-43596 Modeling

Previously, the applied or saved prefix for the steel item part numbering series was not used, but instead the prefix defaulted to the value P. This has now been fixed and the applied and saved values work correctly.

TTSD-43838 Modeling

Sometimes perpendicular snapping happened to an unrelated, distant point. This has now been fixed.

TTSD-44069 Modeling

Previously, when the Cut object with line command was used, no ortho symbols were shown irrespective of the cursor position. This now been fixed.

TTSD-44693 Modeling

Previously, the workplane changed to model origin if you typed the values, for example, when you extended a beam. This has now been fixed.

TTSD-45154 Modeling

 

In some cases, solids could be broken in cut bent plates, for example. This has now been fixed.

TTSD-45156 Modeling

In the US environment, shape names that only consisted of numerical characters were unintentionally converted to imperial units. This affected filtering in the Object Group dialog box and labels in the 3D views. This has now been fixed.

TTSD-45223 Modeling

When the Fast representation was used for parts, some pour object faces were not shown in pour views. This has now been fixed.

TTSD-43403 Core

Sometimes Tekla Structures could crash at startup. This has now been fixed.

TTSD-44427 Core

Previously, Tekla Structures crashed when the bolt visibility was set to Exact in 3d views. This has now been fixed.

TSAC-5363 Tools and components

Previously, the Applications & components catalog could be empty when the Windows regional setting Beta: Use Unicode UTF-8 for worldwide language support was selected. This has now been fixed. Note that it is not recommended to use this setting with Tekla Structures.

TTSD-45196 Numbering

If you cancelled the save-numbering-save operation, Tekla Structures might sometimes crash. This has now been fixed.

TTSD-38333 User interface

Previously, in some rare cases, there was an error in the property pane about object reference not set to an instance of an object. This has now been fixed.

TSAC-5410 Import, export, interoperability (concrete)

Export ELiPLAN file (68): The data conversion file now supports the wildcard "*" in regular expressions in the first column for finding strings from Tekla Structures objects.

TSAC-5435 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, the UT_REBAR_TYPE UDA was not read for rebar sets. This has now been fixed.

TSAC-5471 Import, export, interoperability (concrete)

BVBS Export: All bending and arc angles are now rounded to the nearest 0.5 degree. For example, 89.8 degrees will be rounded to 90 degrees.

TSAC-5484 Import, export, interoperability (concrete)

Export ELiPLAN file (68): You can now specify the material code using the new setting, Material code, on the Data content tab. The options are Name, Assembly prefix, Material, Profile, UDA, Text[TEMPLATE], and Template.

TSAC-5490 Import, export, interoperability (concrete)

BVBS export: When you select One file per each cast unit and use Assembly template property, the export will now warn if the export results in duplicate file names. The export will still continue.

TSAC-5543 Import, export, interoperability (concrete)

BVBS Export: The file naming template by [Assembly template] now works with the PROJECT.NUMBER property.

TSAC-5566 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Exported files are now written with UTF-8 encoding.

도움이 되었습니까?
이전
다음