2019 SP5: New features and improvements

Tekla Structures
2019
Tekla Structures

수정

결함 번호 개발 영역 설명
TSAC-2734 Concrete components The Update rebar attributes tool now has a new Update (phase only) button with which you can update just the phase of all rebar coupler/end anchor parts.
The existing Update button still functions as before. You can use the Update button to update the coupler/end anchor-specific UDA values in addition to the phase of coupler/end anchor parts.
TSAC-3398 Concrete components Lifting anchor (80): You can now select to allow anchor distribution based on percentage of the length.
TSAC-3466 Concrete components Precast foundation block (1028): You can now define angles for grooves on the Grooves tab.
TSAC-3513 Concrete components Anchor (10): The top and bottom offsets were incorrectly calculated for parts with complex parametric profiles and parts that have been cut. This has now been fixed.
TSAC-3523 Concrete components Concrete console (111): Assembly type is now correctly loaded.
TSAC-3524 Concrete components Concrete beam-beam (112): The box used for defining the length of the first washer on the Anchors tab is now dimmed properly.
TSAC-3556 Concrete components Embedded anchors (8): Previously, only concrete parts have been taken into calculations when using the Assembly without steel parts option on the Placement tab. This has now been fixed and miscellaneous parts are also considered.
TSAC-3569 Concrete components Two sided seating with dowel (76): The drainage hole is now generated properly around custom parts.
TSAC-3587 Concrete components The Wall layout dialog box now supports high-resolution screens with high scaling.
TSAC-3595 Concrete components Concrete console (110): The cast unit numbering standard is now loaded and saved properly for all parts.
TSAC-3602 Concrete components Concrete console (110): Previously, incorrect extra secondary parts were found when you defined them using the class or name. This has now been fixed.
TSAC-2359 Steel components In U.S. Base plate (1047), in some situations, two anchors were previously added to the same assembly. This has now been fixed.
TSAC-2680 Steel components Previously, Metsec side rails were wrongly being reported as riveted C rails. This has now been fixed.
TSAC-2878 Steel components UltraZED Cold rolled sleeved (107): When using a ULT-AB1 profile as the stay cleat profile, the stay was not created correctly. This has now been fixed.
TSAC-3368 Steel components Splice type 1 (56): The Round web plate dimensions option on the Parameters tab now works correctly.
TSAC-3440 Steel components Previously, Metsec RoundLok anti-sags were incorrectly creating bolts rather than holes. This has now been fixed.
TSAC-3531 Steel components Brace middle tubes and plate (144): Connection plates are now bolted to the gusset plate in the correct order.
TSAC-3536 Steel components Tube gusset (20): Previously, both above and below line welds were created as above line welds. This has now been fixed.
TSAC-3693 Steel components Brace corner tubes and plate (44): Connection plates are now bolted to the gusset plate in the correct order.
TSAC-917 Steel components Angle profile box (1040): Upper stiffener thickness, width and height are now correctly applied.
TTSD-30725 Organizer In Organizer, project properties were not previously exported to Excel. This has now been fixed.
TTSD-31350 Organizer Previously, synchronization in Organizer was cancelled when the selection in the model was changed. This has now been fixed.
TTSD-17311 Import, export, interoperability IFC2x3 export: The export type Coordination view 2.0 did not always create correct geometry for contour plates with corner chamfers. This has now been fixed.
TTSD-22549 Import, export, interoperability DWG export: When exporting a drawing to DWG, part hatch pattern HSTON3E0 looked wrong if the scale was not the same in X and Y directions. This has now been fixed.
TTSD-28033 Import, export, interoperability IFC export: The grids were exported incorrectly if you used a base point in the export. This has now been fixed.
TTSD-28999 Import, export, interoperability DWG export: The export now handles base point offsets better.
TTSD-29882 Import, export, interoperability DWG export: When exporting a drawing in US imperial environment, the preview window width was sometimes not enough to show the whole drawing. This has now been fixed.
TTSD-30924 Import, export, interoperability DWG export: The export is now more reliable when plotting pull-out pictures in templates.
TTSD-31129 Import, export, interoperability IFC2x3 export: The property set mapping double accuracy type is now working correctly, and the size of the export file is reduced.
TTSD-31360 Import, export, interoperability DWG export: The export now launches a bit faster than before.
TTSD-31430 Import, export, interoperability DWG export: The export is now more robust when the Educational license is in use.
TSAC-3178 Drawings Rebar group dimensioning: The start value of absolute dimensions is now shown correctly again in the Rebar group dimensioning application.
TSAC-3454 Drawings Rebar group dimensioning: The tool now takes the view depths into account to determine the part shape. Previous only the view plane was used.
TTSD-19815 Drawings The Document manager error handling has been improved. Now a message is shown if there is a problem reading any of the saved settings files.
TTSD-25906 Drawings The Delete button in Document manager has been improved. Now, if you have selected documents in Document manager, clicking Delete deletes selected documents. You can no longer accidentally delete model objects by clicking Select objects in the model for selected drawings and then clicking Delete.
TTSD-26477 Drawings The rebar dimension line now works better for those rebar groups that do not have a planar shape, such as a 3D shape.
TTSD-2741 Drawings "ą" diacritics could not be used in drawing text window - using shortcut for this letter selected entire text. This has now been fixed.
TTSD-27794 Drawings Part marks with the Fittings (NS/FS) element can now be merged more reliably.
TTSD-29764 Drawings Inquiring a rebar set from within a drawing did not highlight the corresponding bars in the model. This has now been fixed.
TTSD-30812 Drawings In some cases rebar mark was incorrectly placed. This has now been fixed.
TTSD-30862 Drawings Sometimes precast parts with more than 500 edge lines were incorrectly shown in drawing views. This has now been fixed,
TTSD-31166 Drawings Opening general arrangement drawings that were created in Tekla Structures versions older than 2017 is now faster.
TTSD-31361 Drawings In some cases, when a GA drawing view was created with certain view settings, it would behave incorrectly when you adjusted the view frame. This has now been fixed.
TTSD-31938 Drawings When moving views from one drawing to another, some dimensions were sometimes rotated a bit. This has now been fixed.
TSAC-3428 Reinforcement Rebar shape manager has been changed so that a bar that contains multiple sequential bends forming a circular arc (according curve tolerance) is converted to an arc only when the bending angles are smaller than ~34 degrees. In practice, a 10-sided polygonal stirrup will never be converted to a circular arc but if the stirrup contains 11 or more sides, it may be converted to a circular arc if it fulfills the curve tolerance value.
TTSD-27826 Modeling In some cases, for example, when the plane of a part face or an opening face ran through an opening in the part and its pour break plane, the pour break was not created or it became invalid. This has now been fixed.
TTSD-29843 Modeling Previously, it was not possible to enter the decimal symbol after the inch symbol when defining radial grid properties in the property pane or when using the Radial grid component. This has now been fixed and you can enter values in the format 1'-2".5, 1-2".5, or just 2".5.
TTSD-29844 Modeling Previously, it was not possible to enter the decimal symbol after the inch symbol when defining rectangular grid properties in the property pane. This has now been fixed and you can enter values in the format 1'-2".5, 1-2".5, or just 2".5.
TTSD-31395 Modeling Certain types of pour breaks now work on slabs with recesses.
TTSD-31525 Licensing The error message for an expired Tekla Structures license has now been fixed.
TTSD-21410 Tools and components Outdated locked custom part instances are no longer automatically updated when they or their objects are unlocked.
Outdated custom parts are updated to use the latest definition with modify when the custom part or its objects are not locked anymore.
TTSD-27133 Tools and components The Shape value type is now available in the custom component editor. You can use it to open the shape catalog from the custom component dialog box.
You can use the new value type in existing custom components that include items by editing the components.
TTSD-32086 User interface The contextual toolbar now loads the previously used contextual toolbar profile when Tekla Structures is started even if the profile file is saved in the firm folder. The firm folder location needs to be defined in the teklastructures.ini file.
TTSD-32668 User interface Previously, Tekla Structures sometimes crashed when you tried to drag a floating side pane window or the changes list. This has now been fixed.
TSAC-2470 Import, export, interoperability (concrete) Export Unitechnik (79): Previously, when a double wall shell was created from more than one part and the Cut outer assemblies option was switched on, the embeds in the secondary part were missing from the export with certain Export Groups settings. This has now been fixed.
TSAC-2594 Import, export, interoperability (concrete) Export EliPlan file (68): When using the Export using filter setting, the logging of excluded cast units has been improved.
TSAC-3171 Import, export, interoperability (concrete) Export Unitechnik (79): On the TS configuration tab you can now set Export CONTOUR to Simplified, which exports a simplified contour using 4 x,y corner points of the element.
TSAC-3189 Import, export, interoperability (concrete) Export EliPlan file (68): A new tab Data settings was added, and some settings were moved to the new tab from the Data content tab.
TSAC-3191 Import, export, interoperability (concrete) Export EliPlan file (68): EliPlan export now supports export version 3.0 (FloorMES).
TSAC-3192 Import, export, interoperability (concrete) Export Eliplan file (68): The export now supports export of weep holes in version 3.0.
TSAC-3193 Import, export, interoperability (concrete) Export EliPlan file (68): The export now supports the export of accessory code to plotter data in version 3.0.
TSAC-3194 Import, export, interoperability (concrete) Export EliPlan file (68): The new EliPlan export version 3.0 supports the export of stack results. You can select if the UDA is read from the main part or from the cast unit.
TSAC-3269 Import, export, interoperability (concrete) Export EliPlan file (68): It is now possible to specify a UDA to read the strand code. Default reads the value from the TS_STRAND_CODE UDA.
TSAC-3420 Import, export, interoperability (concrete) Export EliPlan file (68): Plotter data for cuts and recesses exported as lines will have the thickness/depth value, in case the cut is of even depth.
TSAC-3484 Import, export, interoperability (concrete) Export Unitechnik (79): Previously, braced girders within the STEELMAT block were not exported when the STEELMAT block was otherwise empty. This has now been fixed.
TSAC-3488 Import, export, interoperability (concrete) Export  Unitechnik (79): Braced girders modeled with only two chords are now correctly recognized and exported.
TSAC-3518 Import, export, interoperability (concrete) Export Unitechnik (79): When the BRGIRDER block is exported within the STEELMAT block, the STEELMAT insertion coordinates are now correctly adjusted in case the girder minimum coordinate points are outside the mesh.
TSAC-3521 Import, export, interoperability (concrete) Export EliPlan file (68): The Tag for lifters setting has been improved and now also rebars can be specified as lifters using class or name. Now Tag for lifters also has option to specify how the lifters geometry should be plotted - as outline or as center point. It is also possible to specify plotting of additional reinforcement as bounding box or as lines using the setting Plot additional reinforcement or Plot cutout/embed as lines.
TSAC-3522 Import, export, interoperability (concrete) Export EliPlan file (68): Export version 3.0 supports the export of accessory code for openings.
TSAC-3525 Import, export, interoperability (concrete) Export EliPLAN file (68): Recesses that cut the complete area of the element are now plotted.
TSAC-3541 Import, export, interoperability (concrete) Export Unitechnik (79): The Extend contour and add formwork option on the TS configuration tab has been improved. Now, formwork is not added if there is already an embed with the same geometry. Also, the contour is not extended for electric tube embeds.
TSAC-3543 Import, export, interoperability (concrete) Export Unitechnik (79): The Double wall turned setting  on the TS configuration tab has been improved. The No option has been renamed to option No, one coordinate system and new option No, shell-specific coordinate systems has been added to export second shell in the Z direction from the bottom of the pallet upwards.
TSAC-3555 Import, export, interoperability (concrete) Export Unitechnik (79): Previously, when you exported braced girders within the STEELMAT block but with mesh filtered out, the reinforcement block was exported as empty. This has now been fixed.
TSAC-3592 Import, export, interoperability (concrete) Export Unitechnik (79): Electric tubes are now not excluded for the whole length when you use the Cut outer assemblies option together with non-turned double walls.
TSAC-3656 Import, export, interoperability (concrete) Export Unitechnik (79): Previously, line attributes were not exported for second shell of the double wall when Double wall turned was set to No, shell-specific coordinate systems on the TS configuration tab. This has now been fixed.
TSAC-3704 Import, export, interoperability (concrete) Export EliPlan file (68): Previously, full depth cuts placed at hollow core profile chamfer lines with certain profiles  were exported with incorrect geometry. This has now been fixed.
도움이 되었습니까?