Tekla Structures 2019 fixlist
2019
Tekla Structures
Fixes
| Defect number | Development area | Description |
|---|---|---|
| TSAC-138 | Concrete components | In Wall to wall connection and Wall groove seam detail, the connector and recess spacing now work properly when other than millimeter units are used. |
| TSAC-1512 | Concrete components | In Reinforced concrete stair (95), the rebars defined on the Bar J tab are now created correctly when the number of steps is 4. |
| TSAC-1615 | Concrete components | Wall layout T connector now applies straight ends to parts both in the main and in the secondary wall layouts. Previously, only the end of the shorter part, depending on the properties, was made straight. |
| TSAC-1656 | Concrete components | In Floor layout, an extra part was previously created at an opening. This has now been fixed. |
| TSAC-1684 | Concrete components | In Floor layout, the default/actual offsets of other layers than the primary layer now work properly also when other layers consist of multiple parts, and the offset is smaller than the offset of the primary layer. Note that if you are modifying an existing Floor layout created with a previous Tekla Structures version, the layout may change if the offset values were not properly used earlier. |
| TSAC-1741 | Concrete components | In Lifting anchor (80), the anchors are now created correctly when rotated perpendicular to the part. |
| TSAC-1749 | Concrete components | In Mesh bars and Mesh bars by area, when you set the secondary bars to Same as primary and the bar type to Mesh on the Picture tab, the Spacing and Number of bars settings are now correctly dimmed. |
| TSAC-1754 | Concrete components | In Mesh bars, line cuts now work correctly when the Cut bars setting on the Detailing tab is set to Yes, but ignore cuts by name. |
| TSAC-1778 | Concrete components | In Wall layout, you can now again open the Wall layout opening dialog box from the contextual toolbar. |
| TSAC-1878 | Concrete components | In Braced girder (88) and Braced girder (89), the positions in plane and in depth are now correctly applied when creating the braced girder as a profile. |
| TSAC-1930 | Concrete components | In Embedded anchors (8), welds between the custom components and the main part are now correctly created. |
| TSAC-1932 | Concrete components | In Corbels and recesses (82), the Position in plane offset is now correctly applied for the Middle position. |
| TSAC-1947 | Concrete components | In Hollow core lifting loops, the core filling was not created in the middle core if the number of cores was uneven, 5 or 7, for example. This has now been fixed. |
| TSAC-2004 | Concrete components | In Mesh bars, direct modification now works correctly so that the correct bar is moved when dragged. |
| TSAC-2008 | Concrete components | In Wall layout seam, you can now use negative gap values. Note that if you have an existing wall layout with any negative gap values which earlier lead to zero, the gaps will be changed (to a negative gap) in the next update of the wall layout. |
| TSAC-2119 | Concrete components | In Inverted tee beam - automated reinforcement layout (52), Ledge beam - automated reinforcement layout (53), Rectangular beam - automated reinforcement layout (54), Ledge spandrel - automated reinforcement layout (55), Rectangular spandrel - automated reinforcement layout (56) and Reinforcement Strand Layout (66), you can now specify an external CSV file for unlimited loading of strand rebars on the Strand pattern tab. |
| TSAC-2125 | Concrete components | In Wall layout, layer properties are now loaded correctly. Previously, the properties were only loaded for the first layer when you opened the Wall layout dialog box of an existing wall layout, or clicked the Load button when opening the Wall layout dialog box for the first time. |
| TSAC-2134 | Concrete components | Lifting anchor (80) now works correctly for elements created from concrete and miscellaneous materials. |
| TSAC-2152 | Concrete components | Previously, Floor layout updating was not working properly if the layout had a break line and the layout direction was from right to left. This has now been fixed. |
| TSAC-2213 | Concrete components | In Wall layout, with some layer components, the attribute setting was not updated when modifying, and the available attribute settings disappeared from the list of attribute settings. This has now been fixed. |
| TSAC-2251 | Concrete components | Floor layout now creates additional tabs for user-defined attributes in the Floor layout dialog box if there are a lot of user-defined attributes. Earlier, if there were a lot of user-defined attributes, the row spacing on the User defined tab was compressed to fit all the attributes on one tab. |
| TSAC-2328 | Concrete components | Wall panel reinforcement could previously crash if the mesh did not exist in the mesh database. Also, when U bar spacing was set to lower than 0, Wall panel reinforcement could stop working. These have now been fixed. |
| TSAC-2413 | Concrete components | In Concrete console (110), anchors are now placed automatically in the middle of the main part when the console is not created. |
| TSAC-752 | Concrete components | In Wall panel reinforcement, previously, the door opening U-bar reinforcement was incorrectly using wall panel edge reinforcement settings. Now the door opening U-bar reinforcement is using opening reinforcement settings (that is, the same settings that are used for windows opening reinforcement). |
| TSAC-822 | Concrete components | In Reinforcement strand layout (66), the middle debond functionality has been added. There are now two additional Middle debond columns To start and To end on the Strand pattern tab. |
| TSAC-1164 | Steel components | In Wraparound gusset (58), Hollow brace wraparound gusset (58) and Wraparound gusset cross (60), you can now specify erection clearances for different sides on the Gusset tab. |
| TSAC-1459 | Steel components | In Shear plate tube column (189), the plate chamfer size now correctly follows the value defined in the component dialog box. |
| TSAC-1489 | Steel components | In Two sided clip angle (143), web clearance with the weld gap option on the Parts tab now works correctly. |
| TSAC-1540 | Steel components | In Column with stiffeners W (182), the stiffener weld preparation now works properly. |
| TSAC-1718 | Steel components | In Two side clip angle (33), the distance of the secondary bolts from the edge of the clip angle is now correctly applied. |
| TSAC-1809 | Steel components | In Two sided clip angle (143), it is now possible to sort the secondary parts by their profile height. When set to Yes, the highest secondary part is always regarded as the first secondary part, regardless of the selection order. The selection order of secondary parts no longer affects the copying of secondary parts. |
| TSAC-1834 | Steel components | In Hollow brace wraparound gusset (59), you can now control the bolt type separately for gusset side and bracing side bolts on the Brace bolts 1 and 2 tabs. |
| TSAC-1864 | Steel components | In U.S. Seat connection 3 (74), the seat profile stiffeners are now created correctly regardless of the selection order of the secondary parts. |
| TSAC-1875 | Steel components | In Column - 2 beam (14), there were previously issues when you created one plate and the bolts were placed incorrectly. This has now been fixed. |
| TSAC-1898 | Steel components | In Fitting (13), notch cuts are no longer created when the main part is a plate. |
| TSAC-1902 | Steel components | In Column with stiffeners (186) and Column with stiffeners S (187), the issue with the weld missing from between the stiffener and the main part has been fixed. |
| TSAC-1961 | Steel components | Stiffened base plate (1014): on the Parts tab, the Class option has been added for Plate, Web plates, Flange plates and Leveling plate. The Finish option has been added for Plate, Web plates, Flange plates, Leveling plate, Fitting plates, Additional beam, Horizontal plates and L profiles. |
| TSAC-1963 | Steel components | Tube crossing (22) now works correctly with negative brace notch distances. |
| TSAC-2018 | Steel components | In Tensioner brace and compression bar (13), the Side where the levels are calculated for parts options are now calculated properly for cut/fitted main parts. |
| TSAC-2079 | Steel components | In Handrail 1 (74), the bolt assembly and bolt length increase settings on the Bolts tab now work correctly. |
| TSAC-2111 | Steel components | In Stanchion side plate (83), you can now set the bolt spacing when creating a rectangular or a diamond plate. Also, the component now works correctly when the direction if set to auto. |
| TSAC-2124 | Steel components | In Tube gusset (20), the end plates are now created correctly. |
| TSAC-2159 | Steel components | In End plate (29), stiffener material is now correctly applied. |
| TSAC-2199 | Steel components | In Full depth S (185), you can now define the tab plate end cut on the Plates tab. |
| TSAC-2230 | Steel components | In Clip angle (141), weld 5 between the stiffener and the main part is now created correctly. |
| TSAC-2309 | Steel components | In Welded column with stiffeners (128), you can now turn on or off the weld preparation creation in the welds dialog box. |
| TSAC-2310 | Steel components | In Welded beam column (31), you can now turn on or off the weld preparation creation in the welds dialog box. |
| TSAC-2369 | Steel components | In Corner tube gusset (56), you can now separately control the bolt types of Brace bolts 1 and 2 on the gusset side and the bracing side. |
| TSAC-2377 | Steel components | In Tube gusset (20) and Hollow brace wraparound gusset (59), the slotted hole properties on the bracing side are now applied correctly. |
| TSAC-2386 | Steel components | In Bolted moment connection (134), slotted holes for the lower flange plate are now applied correctly. |
| TSAC-2399 | Steel components | In Tube gusset (20), previously, welding was not created when you only specified the below line weld properties for weld 2. This has now been fixed. |
| TSAC-2419 | Steel components | In Wraparound gusset (58), the slotted holes for the additional bolts in clip angles are now applied correctly. |
| TSAC-2445 | Steel components | In H&V Sloped Shear Pl (29), H&V Shallow Shear Pl (30), Bent Shear Plate (48) and H&V Shear Pl (64), you can now define the top and bottom notch radiuses. |
| TSAC-2452 | Steel components | In Rebar hole, when Rounding type on the Parameters tab is set to Round by table and Hole type on the Advanced tab is set to Part cut or Bolt hole + part cut, if the maximum rebar diameter value in the table is smaller than the rebar diameter defined in the rebar properties, Tekla Structures displayes a warning message: Rebar diameter from table is smaller than the rebar diameter from model. |
| TSAC-2456 | Steel components | In Haunch (40), an unwanted chamfer was previously created on the partial stiffener. This has now been fixed. |
| TSAC-2522 | Steel components | In Cage ladder (S60), the parts welded to the ladder no longer lose welds when the component is modified. |
| TSAC-253 | Steel components | In Column with stiffeners S (187), the bolt edge distance is now correctly applied with sloped beams. |
| TSAC-2563 | Steel components | In Brace corner tubes & Pl (44), parts no longer get new a ID when modifying the component. |
| TSAC-2587 | Steel components | In Bolted moment connection (134), Column with stiffeners W (182) and Column with stiffeners (188), the doubler plate cut for avoiding a clash with the main part is now created correctly. |
| TSAC-581 | Steel components | In Ship ladder, the default plate profile prefix is now used for detail B. |
| TSAC-796 | Steel components | In Bent plate (151), the distances of bolts from the edge of the plate are now correctly applied. |
| TSAC-946 | Steel components | In Welded beam to beam (123), the bottom flange notch size is now correctly applied. |
| TSAC-994 | Steel components | In Tube gusset (20), the weld number 2 now works better. |
| TTSD-13621 | Steel components | When using Excel design with connections, if the .xls file is not found, the error message is no longer hidden behind other windows on the screen. |
| TTSD-14141 | Organizer | Previously, Organizer synchronization sometimes failed with some rebar sets. This has now been fixed. |
| TTSD-17116 | Organizer | Previously, an invalid assembly in the model could prevent Organizer from opening. This has now been fixed. |
| TTSD-18471 | Organizer | Previously, if the original reference model file was deleted, the reference model objects were not added to Organizer categories. This has now been fixed. |
| TTSD-18533 | Organizer | Previously, opening Organizer in models that included very large assemblies took a long time or was altogether impossible. This has now been fixed. |
| TTSD-19256 | Organizer | In Organizer, the content of categories that have filters in the category rules is now updated correctly when synchronizing with the model. Previously, if you exploded a component in the model, the category content was not updated correctly. |
| TTSD-19633 | Organizer | In Organizer, when you clicked Image
 |
| TTSD-12817 | Import, export, interoperability | The user-defined attributes added in Tekla Structural Designer are now imported to Tekla Structures with the same name, without the "TSD_" prefix, and they are truncated to 19 characters. |
| TTSD-14041 | Import, export, interoperability | Point cloud density issue with scaled point clouds has been fixed. |
| TTSD-14830 | Import, export, interoperability | Previously, the imported items in .xml or .tez format were stored under an old model folder if you used the Save as command. This has now been fixed. |
| TTSD-15599 | Import, export, interoperability | In reference model change detection, the reference model rotation changes are now detected better. |
| TTSD-15953 | Import, export, interoperability | In IFC object conversion, WallStandardCase is again converted as panel. End joins are ignored and therefore the geometry is not always according to the original geometry. |
| TTSD-16610 | Import, export, interoperability | Trimble Connector no longer automatically shuts down at startup if you have no Trimble Connect Structural license. |
| TTSD-17672 | Import, export, interoperability | .db1 models can now be used as reference models again. |
| TTSD-17799 | Import, export, interoperability | IsExternal, LoadBearing and FireRating properties are included to the wall property set. |
| TTSD-17816 | Import, export, interoperability | The default IFC entity of an object is defined automatically in the tools in which they are created. The default IFC entity can be changed in the IFC export settiings. This only worked for model parts that were found first. The IFC entity is now changed correctly for all parts. |
| TTSD-17891 | Import, export, interoperability | In IFC object conversion, rectangular arbitrary footprint walls are again converted as panels. |
| TTSD-18374 | Import, export, interoperability | Sometimes, multi-geometry IFC B-rep object conversion only converted one of the geometries. This has now been fixed. |
| TTSD-18689 | Import, export, interoperability | In IFC object conversion settings, the Primary profile mapping and Tolerance values were not always visible in the dialog box. This has now been fixed. |
| TTSD-19976 | Import, export, interoperability | In IFC import, handling of objects with a lot of openings was really slow, which appeared like Tekla Structures was not responding. This has now been fixed. |
| TTSD-20194 | Import, export, interoperability | Importing an empty model using the Import model command caused an application error. This no longer happens. |
| TTSD-20216 | Import, export, interoperability | With the IFC2x3 export using the Coordination and Steel Fabrication model view definition, the beams and columns that have a fitting plane at both ends are shorter than in the model. The error does not occur when line cuts are used instead or only one fitting is used. This has now been fixed. |
| TTSD-20249 | Import, export, interoperability | Inserted IFC object properties that used to be visible in inquire in previous versions are visible again, but categorized a bit differently. |
| TTSD-20455 | Import, export, interoperability | The rebar segmentation now works better in IFC export. |
| TTSD-20772 | Import, export, interoperability | In IFC export, the length of a hole is now fixed to be material thickness plus the tolerance value. |
| TTSD-20988 | Import, export, interoperability | When you cancelled the drawing opening, opening the reference model side pane in certain moment caused freezing of the reference model side pane. This has now been fixed. |
| TTSD-21526 | Import, export, interoperability | Trimble Connector no longer logs out when it is closed. |
| TTSD-21654 | Import, export, interoperability | Tekla Structures sometimes closed itself without a warning when a point cloud was picked for dimension or object creation and zooming was done at the same time. This has now been fixed. |
| TTSD-21996 | Import, export, interoperability | Double-clicking the reference model group did not open the Group name dialog box. This has now been fixed. |
| TTSD-22194 | Import, export, interoperability | DWG drawing export: DWG export file name does not have revision info added if the revision info is not present in the format string. |
| TTSD-3743 | Import, export, interoperability | Export to Tekla Structural Designer with analysis model For steel beams and braces, the export to Tekla Structural Designer checks if the difference between the analysis and the physical models requires different global offsets at the start and end of the member. This can result from different offsets at start and end or the analysis settings for the part. The import from Tekla Structural Designer is not affected because we do not change position at all. Export to Tekla Structural Designer with physical model For steel beams and braces, the export to Tekla Structural Designer checks if there are different offsets at start and end and convert them to global offsets. The import from Tekla Structural Designer will reverse the transformation and include the relevant data in the Comparison form when updating. |
| TTSD-7136 | Import, export, interoperability | Tekla Structures now shows a confirmation message when you delete shapes from the shape catalog. |
| TPLED-33 | Templates and reports | Templates now support numbers between -2^64 and +2^64–1. |
| TPLED-87 | Templates and reports | When the columns in a template had continuous horizontal fill, the rows and columns were misaligned. This has now been fixed |
| TTSD-14409 | Templates and reports | TOP_ and BOTTOM_LEVEL_PROJECT/BASEPOINT template fields provided wrong values. This has now been fixed. |
| TTSD-18428 | Templates and reports | Table column orientation has now been fixed. |
| TTSD-20733 | Templates and reports | Previously ASSEMBLY_BOTTOM_LEVEL_BASEPOINT, ASSEMBLY_BOTTOM_LEVEL_PROJECT, ASSEMBLY_TOP_LEVEL_BASEPOINT, ASSEMBLY_TOP_LEVEL_PROJECT were showing wrong values. Now correct values are shown. |
| TTSD-21637 | Templates and reports | Radius symbols in rebar pull-out pictures in reports were sometimes incorrectly drawn after opening drawing, but correct after refreshing the report. This has now been fixed. |
| TTSD-22805 | Templates and reports | Template column rows no longer get overlapped. |
| TTSD-23757 | Templates and reports | Template report text with line break outputs no longer corrupts reports. |
| TTSD-4186 | Templates and reports | Previously, part attributes starting with ASSEMLBY_TOP_LEVEL and ASSEMLBY_BOTTOM_LEVEL were not returning correct values. This has now been fixed, and the attributes are returning the values provided by the counterparts in ASSEMBLY. attributes. |
| 129722, TTSD-2757 | Drawings | Manually changed section numbers did not work correctly in multidrawings. This has now been fixed. |
| TPLED-93 | Drawings | Added new string function, called replace, for rules and valuefield formulas. This function replaces all specified substrings with another string. |
| TSAC-1795 | Drawings | Pattern lines in a drawing are now updated automatically when you have modified the pattern line and reopen the drawing. |
| TSAC-1819 | Drawings | When you open a drawing that contains pattern lines, and the .clp file of a pattern line is missing, a report window will be displayed. The report will contain a list with the name of each pattern line that does not have a related .clp file. Image
 |
| TTSD-10657 | Drawings | Mark contents are now always updated at drawing opening, even though the object is not modified (UDA change, environment change) |
| TTSD-10813 | Drawings | When cloning single part, assembly or cast unit drawings, if the cloning template had views which were aligned in X or Y axis at the center of gravity point, the resulting cloned drawing will now try to align matching views based on the center of gravity. |
| TTSD-11588 | Drawings | Adding merged reinforcement marks to rebars that are detached from a cast unit now works better than previously. |
| TTSD-13389 | Drawings | Section mark on linked drawing view are now updated according to changes made in source drawing. |
| TTSD-14105 | Drawings | In a rare case of a complicated part with several cuts, a dimension point was able to move during drawing update causing unwanted change in the dimension line. This has now been fixed. |
| TTSD-14179 | Drawings | Associative notes without leader lines will no longer be re-positioned when the base point is changed. |
| TTSD-14607 | Drawings | The new printing incorrectly displayed a watermark in drawings with the Educational stamp. This has now been fixed. |
| TTSD-14832 | Drawings | DWG drawing export: The DWG export now supports template attributes better in the plot file names defined by the advanced option XS_DRAWING_PLOT_FILE_NAME_A/C/G/M/W. |
| TTSD-14911 | Drawings | Template attributes for drawing width and height are no longer swapped. |
| TTSD-15042 | Drawings | Grid filtering works now also in drawings. |
| TTSD-15481 | Drawings | Manually merged part mark have the merged line type based on the first selected part mark |
| TTSD-15520 | Drawings | The GA dimensioning commands are now activated correctly. |
| TTSD-15754 | Drawings | Sometimes the hatches did not stay inside the enclosing polygon. This has now been fixed. |
| TTSD-15941 | Drawings | Drawing section views are now resized to include all view contents, for example, when an associative note is added so that text part is positioned outside the section view. |
| TTSD-16003 | Drawings | Starting from Tekla Structures 2017i, copying drawing views in a new sheet assembly drawing changed the section name so that it was different than the original. This has now been fixed and works now like it did before Tekla Structures 2017i. |
| TTSD-16069 | Drawings | When cloning assembly and cast unit drawings, dimensions to grid line points are now cloned to corresponding grid line points in the target drawing. |
| TTSD-16411 | Drawings | The origin of the hatch in polygons with a rotated hatch pattern was incorrectly calculated. This has now been fixed. |
| TTSD-16483 | Drawings | The Auto-align marks command now handles vertical marks better. |
| TTSD-16588 | Drawings | Now the rebar groups with only one rebar are shown in drawings even if the Visibility of reinforcing bars in group is set to customized. |
| TTSD-16664 | Drawings | Non-solid imported items are now shown correctly in drawings. |
| TTSD-17026 | Drawings | Before when you created cast unit or assembly drawings using a filter, view level dimensioning produced dimensions for cuts even if the cut part was filtered out. This has now been fixed. |
| TTSD-17226 | Drawings | Bar groups created by using rebar sets are now coming out correctly in drawing cloning. |
| TTSD-17249 | Drawings | Connection marks sometimes lost some of their elements when the Arrange marks and Align marks commands were used. This has now been fixed. |
| TTSD-17432 | Drawings | Previously, Tekla Structures unintentionally changed some view properties when the view settings on the drawing level were modified. This has now been fixed. |
| TTSD-17439 | Drawings | If an existing single-part drawing is included in an assembly drawing, the view placing inside the single-part drawing container frame no longer changes if you run the Arrange drawing views command in the assembly drawing. |
| TTSD-17641 | Drawings | Using object level settings for surface marks did not work correctly in drawing creation. This has now been fixed. |
| TTSD-17697 | Drawings | Section view labels in linked section views in drawings now work correctly. |
| TTSD-17717 | Drawings | The view level setting No merge for rebar marks now works better. |
| TTSD-17825 | Drawings | The Only grid labels visible grid property now works both on drawing view and drawing level. This option only shows the grid label and a short section of the grid line. |
| TTSD-17987 | Drawings | Sometimes, the dimension line was drawn incorrectly between the dimension points. This has now been fixed. |
| TTSD-18035 | Drawings | Document manager: Select objects in the model for selected drawings (GA) does did not select a rebar set. This has now been fixed. |
| TTSD-18339 | Drawings | Drawing attribute grids and lists now resize to whole properties page. |
| TTSD-18347 | Drawings | Weld marks in drawings that had the size hidden in the weld mark properties were not drawn correctly. This has now been fixed. |
| TTSD-18360 | Drawings | Neighbour rebars did not work correctly in cast unit drawings. This has now been fixed. |
| TTSD-18368 | Drawings | Rebars of strirrup arc types now have correct length in pull-out pictures. |
| TTSD-18463 | Drawings | Dragging of the bolt mark base points now works better for holes. |
| TTSD-18468 | Drawings | The size of the detail views that were moved to another drawing was not adjusted correctly. This has now been fixed. |
| TTSD-18511 | Drawings | You need to set the advanced option XS_TRY_TO_KEEP_LOCATION_IN_FREEPLACING to TRUE (Default) for the advanced option XS_MARK_INTELLIGENT_POST_FREEPLACE_NEARBY to work. |
| TTSD-18695 | Drawings | Symbols in some dimensions and labels did not appear in printed output. This has now been fixed. |
| TTSD-18705 | Drawings | Sometimes closing a drawing while the snapshot viewer was open, and then closing the snapshot viewer could cause an ASSERTion failure or even a crash. This has now been fixed. |
| TTSD-18741 | Drawings | In drawings, objects will now be updated when you change the view size. |
| TTSD-18742 | Drawings | Views in assembly drawings that contain included single-part views are no longer overlapping after the Arrange views command. |
| TTSD-18851 | Drawings | Custom line types did not always work correctly, for example, in arcs. This has now been fixed. |
| TTSD-18949 | Drawings | When deleting obsolete drawing .dg files, a backup of related snapshot files (.dg.DPM) was unnecessarily moved under the \snapshots folder under the current model folder. This no longer happens. |
| TTSD-18957 | Drawings | When you were direct editing a text cell in the Document manager list, you were unable to enter Shift+R or Shift+P, as these were also registered as shortcut keys. This has now been fixed. |
| TTSD-19286 | Drawings | An error could occur when double-clicking reinforcement drawing tools in the Applications & components catalog. This has now been fixed. |
| TTSD-19304 | Drawings | If a dimension that did not have the << Mark >> tag but had some properties set in the tag attributes, changing the dimension via the contextual toolbar was adding an unwanted tag mark to the dimension. This has now been fixed. |
| TTSD-19317 | Drawings | In Document Manager, the drawing export command did not work when the advanced option XS_USE_OLD_DRAWING_EXPORT was set to TRUE. This has now been fixed. |
| TTSD-19359 | Drawings | Dimension arrows indicating a change in the model object extremes are no longer exported. |
| TTSD-19516 | Drawings | Marks sometimes lost the Position element when you used mark alignment tools in drawings. This has now been fixed. |
| TTSD-19546 | Drawings | Rebar group marks can be moved anywhere again using Shift and drag. |
| TTSD-19579 | Drawings | In Tekla Structures version 2018, scrolling with the middle mouse button while editing some drawings sometimes caused a Tekla Structures application error. This has now been fixed. |
| TTSD-19613 | Drawings | When updating drawings from an older Tekla Structures version to a newer version, certain view names could causes crashes, for example, names that ended in a % character. This no longer happens. |
| TTSD-19630 | Drawings | In Document manager, the Title1 column now sorts correctly in the same way as the Drawing list sorted that column. |
| TTSD-19678 | Drawings | Double-clicking a merged rebar mark now gets the related merged rebar mark properties. |
| TTSD-19690, TTSD-18337 | Drawings | When a point was removed from a dimension set, pin icons on the remaining dimension points could incorrectly show that the points are no longer associative by changing to question marks, while the points still were associative. This has now been fixed. |
| TTSD-19718 | Drawings | Drawing view scales were incorrectly modified when the Autoscale option was changes from Yes to No. This happened only with new drawing dialog boxes. This has now been fixed. |
| TTSD-19763 | Drawings | Adding associative notes without leader lines did not work correctly. This has now been fixed. |
| TTSD-19877 | Drawings | Holding down Shift and dragging now works correctly again for non-associative texts. |
| TTSD-19878 | Drawings | Marks are now correctly sorted in Document manager by taking the alphabetic and numeric components of the mark into account in the same way as in the Drawing List. |
| TTSD-19954 | Drawings | Category search field tooltip for new category no longer starts with several blank lines. |
| TTSD-20020 | Drawings | The Clone button is now always visible in Document Manager even if no drawing is selected. Previously the button was hidden. |
| TTSD-20204 | Drawings | In some cases, an assert was caused by a missing symbol library. This has been fixed, and an error message is displayed instead. |
| TTSD-20209 | Drawings | Tekla Structures crashed when you changed the ruler width of a text with handle. This has now been fixed. |
| TTSD-20285 | Drawings | Adding or updating drawing mesh marks of outline meshes sometimes rotated the marks 90 degrees. This has now been fixed. |
| TTSD-20407 | Drawings | Opening of some drawings could sometimes fail. This has now been fixed. |
| TTSD-20427 | Drawings | When you had set the advanced option XS_ALLOW_REBARS_ON_TOP_OF_EACH_OTHER to FALSE, opening a drawing could sometimes crash. This has now been fixed. |
| TTSD-20698 | Drawings | In some cases, the reference model lines were not cut by the view restriction box in drawings. This has now been fixed. |
| TTSD-20720 | Drawings | After reopening a model, drawing snapshots did not follow Document manager/Drawing list selection. This has now been fixed. |
| TTSD-21275 | Drawings | Dimension tag contents are now always updated on drawing opening. Dimension prefix mark now gets the change cloud correctly. |
| TTSD-21293 | Drawings | When converting a model to a multi user model or reading in a shared model, a model reload occurs and Document Manager was clearing the currently selected documents which caused buttons such as Print, and Export to become hidden. Now the currently selected documents are remembered and the selection is maintained. |
| TTSD-21305 | Drawings | The Flip outside dimension setting in dimension properties produced incorrect info to Undo history. This has now been fixed. |
| TTSD-21456 | Drawings | Non-solid items are now shown correctly in drawings also when they are clipped with the view restriction box. |
| TTSD-21540 | Drawings | Some drawing commands did not use correct info in Undo history. This has now been fixed. |
| TTSD-21541 | Drawings | The Arrange marks and Align marks commands did not use correct information in Undo history. This has now been fixed. |
| TTSD-21607 | Drawings | When converting a model to a multi user model or reading in a shared model, a model reload occurs and Document Manager was clearing the currently selected documents which caused buttons like Print, Export etc., to become hidden. Now the currently selected documents are remembered and the selection is maintained. |
| TTSD-21616 | Drawings | Slanted symbols are now correctly printed and exported. |
| TTSD-21786 | Drawings | Using templates in rebar marks was not working with rebar set tapered groups. That has now been fixed. |
| TTSD-21787 | Drawings | Fixed an issue with pull-out dimensions for tapered rebar set groups. |
| TTSD-21852 | Drawings | In Document Manager, a crash occurred if the user did not have access rights to view files in a folder defined in DocumentManagerFileDocumentSettings.txt. |
| TTSD-22028 | Drawings | Document Manager now behaves the same way as the old Drawing list in that it allows you to open locked drawings for those configurations that allow viewing only of drawings. |
| TTSD-22227 | Drawings | Non-solid items are now shown correctly in drawings also when they are clipped with the view restriction box. |
| TTSD-22317 | Drawings | Sometimes in a drawing with a custom template and small section views, all surface treatments were not properly drawn in all of the views. This has now been fixed. |
| TTSD-22365 | Drawings | Sub-assembly welds in GA drawings now follow the same setting as the main assembly welds. There is no separate option to control sub-assembly welds in GA drawings. |
| TTSD-22391 | Drawings | Rebar sets in drawings were not working correctly if drawings were cloned. This has now been fixed. |
| TTSD-22404 | Drawings | Sometimes there could be an internal ID conflict in drawings, causing a part to be missing from a drawing. This has now been fixed. |
| TTSD-22444 | Drawings | In printing, the Select area option did not produce a correct output. This has now been fixed. |
| TTSD-22673 | Drawings | Linked views were not deleted from a drawing when the source drawing for the linked views was deleted. This has now been fixed. |
| TTSD-23193 | Drawings | Having no marks selected in the drawing will disable mark alignment functions on the ribbon. |
| TTSD-23252 | Drawings | Slanted symbols are now correctly printed and exported |
| TTSD-23307 | Drawings | Holding down Shift and dragging part marks no longer causes an assert. |
| TTSD-23449 | Drawings | There were problems opening a drawing containing failing bolt solids. This has now been fixed and drawings can be opened even if there is a failing bolt solid. |
| TTSD-4111 | Drawings | Previously snap settings in drawings were saved only if you saved the drawing through the File menu. The settings were not saved if you saved the drawing by closing the drawing and selecting the Save option. Now snap settings are saved properly in both cases. |
| TTSD-7562 | Drawings | The Draw cover-up line command now works for lines of all colors and thicknesses. |
| TTSD-7796 | Drawings | Radius dimension associativity now works better. |
| TTSD-7865 | Drawings | Unfolded drawings are now associative, with the limitation of polygon cuts and unfolding lines. |
| TTSD-9467 | Drawings | Shortening line color was incorrect in the print output. This has now been fixed. |
| TTSD-15719 | Tekla Model Sharing | In a shared model, locked components are now better handled during read in. Previously, there were issues with locked components that should have been updated during read in because of changed component definitions. Now such components are not updated during read in. The modelsharing.log lists these components and the reason why they were not updated. |
| TTSD-18318 | Tekla Model Sharing | Previously, Tekla Structures occasionally crashed in certain Tekla Model Sharing situations, with warning messages about an unknown user. This has now been fixed. |
| TTSD-18420 | Tekla Model Sharing | In a shared model, when reading in, conflicts in part numbering were not always propagated to the assembly, which left the assembly numbering unchanged. This has now been fixed. |
| TTSD-18762 | Tekla Model Sharing | Previously, Tekla Model Sharing would sometimes fail to initialize when opening a shared model, with the following error message in the DataSharing client log: "DataSharingException: Facade is not connected to service.". This error has now been prevented. |
| TTSD-18795 | Tekla Model Sharing | Profiles with user-defined cross sections are now imported correctly. Previously, the cross section was not updated when the profile was imported. In shared models, the profiles could be erroneously considered modified, which would cause unnecessary updates to numbering and drawings for parts using the profiles. Now this does this happen anymore. |
| TTSD-19624 | Tekla Model Sharing | Previously, Tekla Model Sharing file handling could copy temporary files to another model, which could make history reading and writing to report database corruption. Now this has been fixed. Such files are never written out and not read during read in. |
| TTSD-21393 | Tekla Model Sharing | With some reference models, the changes list in a shared model could open very slowly. This has now been fixed. |
| TTSD-21567 | Tekla Model Sharing | In Tekla Model Sharing, profiles with a .clb file as a subtype were not previously shared correctly. This has now been fixed. |
| TTSD-22212 | Tekla Model Sharing | In Tekla Model Sharing, canceling the start sharing was not possible during packet creation. This has now been fixed. |
| TTSD-22644 | Tekla Model Sharing | Previously, when reading in, a locked drawing did not override the local changes to the drawing. This has now been fixed. |
| TTSD-22652 | Tekla Model Sharing | In Tekla Model Sharing, read in performance has been improved. |
| TTSD-23046 | Tekla Model Sharing | Previously, if Tekla Structures crashed or if the Tekla Structures process was somehow forced to exit during write out, this could result in missing drawing files. This has now been fixed. |
| TTSD-6851 | Tekla Model Sharing | Saving of shared models is now more robust than before in situations where antivirus and similar software put temporary locks on model files. Failed operations are retried and written in error logs. |
| TSAC-1783 | Reinforcement | Previously, the curve width/height of a curved bar with hooks was not correct in Rebar shape manager (and reports, if used). This has now been fixed. |
| TSAC-2156 | Reinforcement | Previously, Rebar shape placing tool did not create the distances correctly when other than millimeter units were used. This has now been fixed. |
| TTSD-14083 | Reinforcement | Clash check now takes into account rebar set concrete covers and works correctly with protruding rebar set bars. |
| TTSD-15660 | Reinforcement | Leg dimensions are no longer shown for rebar set bars that are in unknown group types. |
| TTSD-16702 | Reinforcement | In some cases, rebar set splitters caused bars to protrude from concrete. This has now been fixed. |
| TTSD-16829 | Reinforcement | Previously, rebar adaptivity would break in some cases, especially if the concrete object had very small angles between the faces. |
| TTSD-18311 | Reinforcement | Previously, when a rebar set with modifiers or splitters was copied, its UDAs were not copied with it. This has now been fixed. |
| TTSD-19172 | Reinforcement | The default value for Layer order number in the Rebar set properties and in the Rebar leg face properties is now Auto. This makes it possible to go back to the default layer order number of zero more easily in the property pane. Previously you needed to load the standard file. |
| TTSD-22045 | Reinforcement | In some cases, rebar segment lengths were reported with slight inaccuracy. This has now been improved. |
| TTSD-22714 | Reinforcement | In the Options dialog box, the page for rebar set related settings has been renamed from Reinforcement to Rebar set. |
| TTSD-12525 | Modeling | When you create new pour breaks, they are now added to the current phase. |
| TTSD-15116 | Modeling | When using orthogonal snapping, the snap points are now shown with perpendicular snap symbols. |
| TTSD-15234 | Modeling | Previously, modeling sketches in the sketch editor could cause an error, and an error message was shown. This has now been fixed. |
| TTSD-15470 | Modeling | Creating closed polybeam structures in the model is now prevented. |
| TTSD-16464 | Modeling | Modifying the phase of objects now redraws the objects in the correct color when the Color by phase option is used in the object representation settings. Previously, the color of the objects did not change when modifying the phase. |
| TTSD-17047 | Modeling | The silhouette edges are drawn correctly again for high accuracy hollow profiles when XS_DISPLAY_FILLET_EDGES is set to FALSE. |
| TTSD-17093 | Modeling | In the property pane, you can now save and load bolt assembly property files that only contain the bolt but no other parts in the assembly. Note that if you select or clear the Bolt check box in the bolt assembly properties, the check boxes for Washers and first Nut properties are also selected or cleared, as in the old bolt properties dialog box. |
| TTSD-17561 | Modeling | Previously, there were some issues in the profile and material catalog export and import, and in editing rules in the profile and material catalog. This has now been fixed. |
| TTSD-17582 | Modeling | Previously, the Move linear command did not move objects which were selected with Object by phases in Phase Manager. Only the grid that was included in the phase was moved. Now, if the grid is the only selected object, it is moved. If also other objects are selected, such as parts, bolts, welds and so on, the grid does not move but the other objects move. |
| TTSD-17652 | Modeling | Now the custom component formulas no longer require an extra click to update another value. |
| TTSD-17915 | Modeling | Sometimes, opening an older Tekla Structures model with a newer Tekla Structures version resulted in invalid time ID errors, and the model could not be opened. This has now been fixed. |
| TTSD-17941 | Modeling | Steel embeds are now ignored when calculating AREA_FORM properties.AREA_FORM properties require solid unions to be used. Small steel embeds can cause problems when creating solid unions, and they do not have a lot of effect on the end result. |
| TTSD-18267 | Modeling | POUR_UNIT. template attributes now work with all mesh types. |
| TTSD-18600 | Modeling | When saving the model with Save as, the model name is now restricted to 40 characters, like when creating a new model. The last 10 model paths are not shown in the Save as dialog box. |
| TTSD-18604 | Modeling | Filtering based on OWNER or HISTORY.OWNER now works with both <DOMAIN>/<username> and <DOMAIN>\<username>. |
| TTSD-18763 | Modeling | Previously, some important messages were classified incorrectly as debug information. This has now been fixed. |
| TTSD-19562 | Modeling | Filtering assemblies by user-defined attributes now again searches attributes from the assembly's main part. |
| TTSD-19845 | Modeling | Previously, splitting and combining parts was not working for all parts. This has now been fixed. |
| TTSD-20309 | Modeling | Previously, when you made the bolts invisible using the Display settings, also the holes disappeared from the model view. This has now been fixed. |
| TTSD-20604 | Modeling | The saving of multi-user models has been improved to work more reliably. |
| TTSD-20700 | Modeling | Previously, saving the model with Save as failed in some situations and Tekla Structures displayed the message Model memory is corrupted. This has now been fixed. |
| TTSD-21250 | Modeling | The coordinate system calculation of plates has been improved. This affects some report properties, for example. |
| TTSD-21481 | Modeling | Previously, selecting two bolts and right-clicking caused Tekla Structures to crash. This happened when the first part you had selected was a cast-in-place part. This has now been fixed. |
| TTSD-21482 | Modeling | Previously, if you left Tekla Structures idle for a while, in some cases Tekla Structures could freeze or crash. This has now been improved. |
| TTSD-22524 | Modeling | Previously, when the Ortho tool was active, the snapping distances were incorrectly rounded. This has now been fixed. |
| TTSD-22670 | Modeling | Previously, if a model with pour breaks had a model view along the XZ or YZ planes created, this would cause pour breaks to be shown as duplicates in the wrong place. This has now been fixed. |
| TTSD-12559 | Analysis and design | Previously, if you had created a rigid link between analysis nodes, you could not move or merge nodes that had been created manually. This has now been fixed. |
| TTSD-12561 | Analysis and design | If the bottom node of a column is a split position of a beam or an intermediate point of a polybeam, no support is created for the node when the column is added to the analysis model. When objects in the analysis model are modified, supports may be created. When Tekla Structural Designer is used as the analysis application, no supports are created. |
| TTSD-12971 | Analysis and design | When importing changes from Tekla Structural Designer to Tekla Structures, you can now rotate the model when the Model Comparison Tool dialog box is open. |
| TTSD-13158 | Analysis and design | Previously, slab and panel hole analysis node positions were not created in the correct plane. This has now been fixed. |
| TTSD-13552 | Analysis and design | When changing the analysis part class to Secondary or Bracing, the Keep axis position option is now set to No. Also, when changing the class to Beam or Column, the Keep axis position option is set to Yes. Note that if you set the analysis application to Tekla Structural Designer and the class to Beam, the Keep axis position option is not changed to Yes. |
| TTSD-14412 | Analysis and design | In the analysis model properties, the Curved beam property is now set to Use curved member when creating a new analysis model with the Tekla Structural Designer analysis application, or when changing the analysis application of an existing analysis model to Tekla Structural Designer. |
| TTSD-16487 | Analysis and design | The Finland environment and the Norway environment now include localized conversion files to be used as the default conversion files in the import and export between Tekla Structures and Tekla Structural Designer. |
| TTSD-17063 | Analysis and design | When importing and exporting files between Tekla Structures and Tekla Structural Designer, if your environment includes a conversion file localized for your environment, this file is now used as the default conversion file, instead of the global mapping files. |
| TTSD-18396 | Analysis and design | Analysis node positions are now correct when using Reference axis (eccentricity by neutral axis) as the analysis axis position. Also, when inquiring analysis parts, the offsets are now shown correctly. |
| TTSD-19340, TTSD-17940 | Analysis and design | Concrete columns and beams with parametric profiles, for example 36"*36" and D24", are now correctly exported from Tekla Structures to Tekla Structural Designer. |
| TTSD-19862 | Analysis and design | Split nodes are now created correctly in situations where the analysis part positions change in analysis model creation. |
| TTSD-19916 | Analysis and design | Concrete panel analysis connectivity has now been improved. |
| TTSD-22080 | Analysis and design | In a Tekla Model Sharing model, when you read in changes that included an analysis model, and an autosaved model was created after read in and the model then reopened without saving, the analysis model could sometimes be lost. This has now been fixed. |
| TTSD-22656 | Analysis and design | Previously, when a user had created an analysis model in a multi-user model and another user saved the model, this new analysis model was not visible for either user in the Analysis & Design Model dialog box. This has now been fixed. |
| SOLD-720 | Core | Fix for Windows 10 Fall Creator update and onwards: It is now possible to switch user correctly regardless of stay sign in option choice. |
| TTSD-19981 | Core | When you tried to change the advanced option XS_DRAWING_PLOT_FILE_NAME_W in Russian language, Tekla Structures crashed. This has now been fixed. |
| TSAC-1710 | Tools and components | Rebar Coupler and Anchor Tools: Previously, the assembly structure was broken when a coupler was created as a custom part and you attached the rebar to another part after the couplers were created. Note that if the assembly hierarchy is already broken, you need to explode the cast unit, or remove the extra part from the cast unit, and update the coupler once to get the couplers added to the correct cast unit. |
| TSAC-2268 | Tools and components | In Rebar shape manager, it was not possible to include any of the ‘Leg to leg’ (D1:2), ‘Along leg’ (K3:1) nor ‘Off from leg’ (H3:1) distances in a rule formula. The formula value was not correctly evaluated and thus the rule result was never true and the OK button was not enabled. This has now been fixed. |
| TTSD-12860 | Tools and components | The contextual toolbar profiles are now fetched from external environment firm folders along with the users' local profile folder. These external profiles can be loaded in, but any changes will still be saved in the users' local folder as new profiles. |
| TTSD-16347 | Tools and components | Previously, when you edited a custom component, then closed the custom component editor dialog box and applied the changes to the custom component instances in the model, a copy of the custom component appeared in the model if any of the component instances had locked parts. Now the extra copy is always removed from the model. |
| TTSD-16349 | Tools and components | Custom components with locked parts are no longer updated when the component is changed. Instead, the Object locks dialog box is opened (Manage > Locks). |
| TTSD-18133 | Tools and components | In the Applications & components side pane window, you can now click the Image
 |
| TTSD-18343 | Tools and components | If a custom part definition is changed, locked custom parts are not updated. If the lock is removed and the custom part is modified, the custom part instance is updated to use the new definition. |
| TTSD-18588 | Tools and components | Custom components containing system components were not correctly created when creating several custom components within one command sequence. This has now been fixed. |
| TTSD-19715 | Tools and components | Previously, closing Tekla Structures after model loading failed could cause Tekla Structures to crash. This has now been fixed. |
| TTSD-20327 | Tools and components | The execution time of custom components that use property files has been optimized. |
| TTSD-23434 | Tools and components | In Tekla Model Sharing models, using Organizer or some other .NET tools could previously cause errors at write out when using the Project viewer role. This has now been fixed. |
| TTSD-20007 | Numbering | When you use standard-part models in numbering, the standard parts now get the start number of the oldest standard part in the actual project model, instead of a random number. The start number cannot be used to divide identical standard parts in groups, as the parts all get the same part position, prefix, and start number. |
| TTSD-22146 | Numbering | Tekla Structures no longer crashes when renumbering objects. |
| SOLD-618 | User interface | In the Support tool, while you create the support case, the navigating back button in the upper-left corner is disabled for a moment so that you cannot accidentally interrupt the upload. |
| TTSD-13217 | User interface | When copying properties in the property pane, the check marks of the properties that you are copying now stay selected. |
| TTSD-18352 | User interface | Previously, the area selection cursor did not work correctly with the latest NVIDIA drivers in OpenGL views. This has now been fixed. |
| TTSD-18464 | User interface | You can now use 2-byte Japanese characters, as well as other multi-byte characters, in the search box in the Tekla Online side pane. |
| TTSD-19192 | User interface | In some cases, copying properties in the property pane did not work. This has now been fixed. |
| TTSD-19949 | User interface | The bolt group distance x and distance y settings in the property pane are now properly updated when loading a property file. |
| TTSD-20068 | User interface | The Image
 |
| TTSD-20802 | User interface | Several fixes have been made to DirectX graphics including improved performance for the shaded wireframe (Ctrl/Shift+2) view mode. |
| TTSD-20918 | User interface | Previously, saving the model with Save as could cause Tekla Structures to crash and restart instead of exiting. This has now been fixed. |
| TTSD-21403 | User interface | The cast unit numbering series in the concrete part property pane is now shown as dimmed if it is changed in the cast unit level. |
| TTSD-22164 | User interface | All virtual stud UDAs for steel beams are now available in the property pane in the US imperial environment. |
| TTSD-22618 | User interface | Previously, if you used ft (decimal) length units and selected a bolt group, the property pane could be empty. Also, if you changed the unit setting to use ft (decimal) while the property pane was open, Tekla Structures sometimes crashed. Now the property pane properly shows the properties of the bolts. |
| TTSD-21256 | Import, export, interoperability (steel) | NC: Sometimes, the pop-marks for middle line were not created. This has now been fixed. |
| TSAC-2068 | Import, export, interoperability (concrete) | In some cases duplicate dimensions were created for double walls or sandwich walls. This has now been fixed. |