Review slab and mat design

Tekla Structural Designer
2021
Tekla Structural Designer

Review slab and mat design

Review slab and mat design status

  1. Open a 2D view at the level of the slab or mat and change the view regime to Review View.
  2. On the ribbon, go to the Review tab.
  3. In the Slab/Mat Design group, click Status.
  4. In the same group, click the drop list to display the filtering options.
    Filter Description

    Overall

    The governing Top X, Top Y, Bottom X, Bottom Y, or span depth result is displayed.

    Reinforcement

    The governing Top X, Top Y, Bottom X, or Bottom Y result is displayed.

    Top X

    The result is only displayed for top reinforcement in the X direction.

    Top Y

    The result is only displayed for top reinforcement in the Y direction.

    Bottom X

    The result is only displayed for bottom reinforcement in the X direction.

    Bottom Y

    The result is only displayed for bottom reinforcement in the Y direction.

    Span Depth

    The span to depth result is displayed.

    Bearing Pressure

    The bearing pressure result is displayed.

  5. Select the filtering option you require.

    Color codes display the design status of each slab and mat for the selected filtering option.

    Tekla Structural Designer uses the following classifications:

    Status

    Description

    Error

    The slab item currently cannot be designed because an error has occurred.

    Beyond Scope

    The slab item cannot be designed because its design is beyond the scope of Tekla Structural Designer.

    Fail

    The slab item has failed one or more design checks.

    Warning

    Although the slab item has passed the design checks, one or more warnings have been issued. Review the warnings before deciding if you need to take further action.

    Pass

    The slab item has passed all design checks.

    Other

    The slab item has not been designed.

Review slab and mat design ratios

  1. Open a 2D view at the level of the slab or mat and change the view regime to Review View.
  2. On the ribbon, go to the Review tab.
  3. In the Slab/Mat Design group, click Ratio.
  4. In the same group, click the drop list to display the filtering options.
    Filter Description

    Overall

    The governing Top X, Top Y, Bottom X, Bottom Y, or span depth result is displayed.

    Reinforcement

    The governing Top X, Top Y, Bottom X, or Bottom Y result is displayed.

    Top X

    The result is only displayed for top reinforcement in the X direction.

    Top Y

    The result is only displayed for top reinforcement in the Y direction.

    Bottom X

    The result is only displayed for bottom reinforcement in the X direction.

    Bottom Y

    The result is only displayed for bottom reinforcement in the Y direction.

    Span Depth

    The span to depth result is displayed.

    Bearing Pressure

    The bearing pressure result is displayed.

  5. Select the filtering option you require.

    Color codes display the design ratio of each slab item for the selected filtering option. N/A is assigned to members that have no ratio or whose ration is smaller than the lowest band. N/A also indicates slab items that are either beyond scope or have yet to be designed.

Review punching check status

Note: In order to see punching check status you must first switch off Slab Items and Slab Patches in Scene Content.
  1. Open a 2D view at the level of the slab or mat and change the view regime to Review View.
  2. On the ribbon, go to the Review tab.
  3. In the Slab/Mat Design group, click Status.
    Color codes display the design status of each punching check.

Review punching check ratio

Note: In order to see punching check ratio you must first switch off Slab Items and Slab Patches in Scene Content.
  1. Open a 2D view at the level of the slab or mat and change the view regime to Review View.
  2. On the ribbon, go to the Review tab.
  3. In the Slab/Mat Design group, click Ratio.
    Color codes display the design ratio of each punching check.
도움이 되었습니까?
이전
다음