Rebar coupler and anchor tools

Tekla Structures
2022
Tekla Structures

Rebar coupler and anchor tools

Rebar coupler and anchor tools is a set of four components that help to model and manage

  • reinforcing bar couplers that connect two bars
  • end anchors that are devices at the unreserved end of the bar.

The following components are part of Rebar coupler and anchor tools:

  • Rebar coupler
  • Rebar end anchor
  • Split rebar and add coupler
  • Rebar end trimming

In addition, you can manage the user-defined attributes (UDAs) of the Rebar coupler and anchor tools with the Update rebar attributes component.

All couplers and end anchors are automatically added to the parent part of the reinforcing bar. This allows them to be shown in reports and drawings because they are added to the sub-assembly of the cast unit.

In some cases the reinforcing bars can move outside of the concrete. This may happen with reinforcing bars that are modeled with two points (straight bars and straight bars with hooks). If the reinforcing bars move outside of the concrete, change the cover thickness to either a negative or a positive value depending on what is required.

Two report templates Rebar Extra Fabrication Length.rpt and Rebar Thread Length.rpt can be used to inquire Threaded Length and Extra Fab. Length of the reinforcing bars in the BOMs or BOQs.

Rebar coupler

Rebar coupler creates couplers to connect reinforcing bars, or reinforcement meshes, whose bar ends are in contact and parallel.

Objects created

  • Round parts

    The parts are created between two reinforcement objects.

Use for

Situation Description

Couplers with split reinforcing bars.

Before you start

Couplers can be created between reinforcing bars or reinforcement meshes. The selected reinforcement objects can be of different type and they can even have different number of bars. The only requirement is that one or more bar ends are in contact and parallel. With rebar sets, the couplers can only be created between spliced bars in that particular rebar set.

Selection order

Reinforcing bars or reinforcement meshes
  1. Select the primary reinforcing bar(s).
  2. Select the secondary reinforcing bar(s).
Rebar sets
  1. Select a rebar set.
  2. Define a location for a splitter by picking two points.

    This splitter will become an input object for the couplers.

  3. Pick a point.

    This point defines the side of the primary reinforcing bar(s). This is needed if you have applied different properties for the primary and secondary bar(s).

or

  1. Select an existing splitter in a rebar set.
  2. Pick a point.

    This point defines the side of the primary reinforcing bar(s). This is needed if you have applied different properties for the primary and secondary bar(s).

Couplers are created at each location where

  • the bar ends are parallel enough (angle < 5 degree) and
  • the gap along the bar end is less than the length of the coupler and
  • the offset perpendicular to the bar end legs is less than the diameter of the bars

When there is no valid and no parallel end-to-end location between the selected bars, the component creates a dummy part that identifies the unsuccessful coupler insertion.

Parameters tab

Use the Parameters tab to define the coupler properties.

Option Description
Use manually entered values Enter values for the coupler properties.
Use auto attribute file

The values in the auto attribute file override the coupler component values.

Typically the auto attributes file contains one or more attribute values to be used with certain bar sizes.

Go to Tekla Warehouse to get auto attribute files for your project.

For more information on the structure of the auto attribute files, see Customize attribute files, part mapping and user-defined attributes (UDAs).

Option Description
Use custom component

Select Yes to create the coupler as a custom part.

Select No to create the coupler as a normal part.

Name

Type the name of the custom component, or select it from the Applications & components catalog.

Ensure that the selected component is a custom part.

Attribute

Type the name of the attribute file of the custom component.

The coupler custom part is created using the saved attributes given here.

Input points The order of the start and the end points of the custom component.
Add to rebar assembly

To add the coupler as a sub-assembly to the rebar assembly, select either Yes, to primary bar or Yes, to secondary bar.

Note that you must first create the rebar assembly, otherwise adding is not possible.

The default value is No.

Option Description
Numbering series Prefix and a start number for the coupler part position number.

In the Inherit from list, select which numbering settings are used for couplers.

  • With None, enter the part and assembly prefix and start numbers.

  • With Rebar, the numbering settings of the primary bars are used.

  • With Cast unit, the cast unit numbering settings are used.

Attributes Name, diameter, material, finish and class of the coupler parts.

1 The overall end-to-end length of the coupler

If you use a custom part, this is the length between the start point and the end point of the custom part.

2 Coupler profile width

3 Coupler offset in relation to the free gap center line. Positive values move the coupler to the right and negative to the left.

You can also control this offset in the auto attribute file by using the attribute CouplerOffset.

When you create the couplers as custom parts, the properties in the Numbering series and Attributes sections can be filled from the custom part settings if you have named the properties in a certain way.

Rebar attributes tab

Use the Rebar attributes tab to define user-defined attributes (UDAs) for rebars.

Option Description
Threaded length

The value is written to the reinforcing bar UDA.

The fields are used for checking which bars have threads and what are the thread values so that they can be shown in drawings and reports.

Extra fabrication length

This value is written to the reinforcing bar UDA.

This value does not affect the length of the reinforcing bar. You need to add this value in your drawings and reports to get the correct length if required.

Method

Type

Product

Code

UDAs written to the reinforcing bars.

You can set the reinforcing bar end method and the coupler type, and add a product name and a code for reporting purposes.

The used attribute name depends on which end of the reinforcing bar the coupler was created.

Note:

The above user-defined attributes affect numbering. Reinforcing bars with different attribute values get different part marks.

Coupler attributes tab

Use the Coupler attributes tab to define user-defined attributes (UDAs) for couplers or end anchor parts. For each UDA, you can select to inherit the value from the rebar or the cast unit. To enter a value, select the inherit option None.

Note that if the cast unit does not have any value for that particular UDA, the value is taken from the main part of the cast unit. By default, you can enter a Comment and values for User field 1 … 4 UDAs. You can customize the set of UDAs by modifying the UDA fields in the RebarCouplers.Udas.dat file, located in the ..\Environments\common\system folder.

Rebar end anchor

Rebar end anchor creates end anchors at the ends of reinforcing bars or reinforcement meshes.

Objects created

  • Round parts

    The parts are created at reinforcing bar ends.

Use for

Situation Description

Reinforcing bars with end anchors.

Selection order

Reinforcing bars or reinforcement meshes
  1. Select the reinforcing bar(s).
  2. Pick any point close to the bar end where you want to create the end anchors.
Rebar set bars
  1. Select a rebar set.
  2. Define a location where to add an end detail modifier by picking two points.

    This end detail modifier will become an input object for the end anchors.

or

  1. Select an existing end detail modifier in a rebar set.

Parameters tab

Use the Parameters tab to define the end anchor properties.

Option Description
Use manually entered values Enter values for the end anchor properties.
Use auto attribute file

The values in the auto attribute file override the end anchor component values.

Typically the auto attributes file contains one or more attribute values to be used with certain bar sizes.

Go to Tekla Warehouse to get auto attribute files for your project.

For more information on the structure of the auto attribute files, see Customize attribute files, part mapping and user-defined attributes (UDAs).

Option Description
Use custom component

Select Yes to create the end anchor as a custom part.

Select No to create the end anchor as a normal part.

Name

Type the name of the custom component, or select it from the Applications & components catalog.

Ensure that the selected component is a custom part.

Attribute

Type the name of the attribute file of the custom component.

The end anchor custom part is created using the saved attributes given here.

Input points The order of the start and the end points of the custom component.
Add to rebar assembly

To add the coupler as a sub-assembly to the rebar assembly, select either Yes, to primary bar or Yes, to secondary bar.

Note that you must first create the rebar assembly, otherwise adding is not possible.

The default value is No.

Option Description
Numbering series Prefix and a start number for the end anchor part position number.

In the Inherit from list, select which numbering settings are used for couplers.

  • With None, enter the part and assembly prefix and start numbers.

  • With Rebar, the numbering settings of the primary bars are used.

  • With Cast unit, the cast unit numbering settings are used.

Attributes Name, diameter, material, finish and class of the end anchor parts.

The dimensions of the end anchor.

If you use a custom part, define the length between the start point and the end point of the custom part using these values.

The offset of the far most point of the coupler measured from the physical end of the reinforcing bar.

Note that you cannot control the end of the reinforcing bar with this component. You need to make sure the end concrete cover of the reinforcing bar is greater or equal to this offset plus the minimum concrete cover.

When you create the end anchors as custom parts, the properties in the Numbering series and Attributes sections can be filled from the custom part settings if you have named the properties in a certain way. For an example, see Customize attribute files, part mapping and user-defined attributes (UDAs).

Rebar attributes tab

Use the Rebar attributes tab to define the user-defined attributes (UDAs) for rebars.

Option Description
Threaded length

The value is written to the reinforcing bar UDA.

The fields are used for checking which bars have threads and what are the thread values so that they can be shown in drawings and reports.

Extra fabrication length

This value is written to the reinforcing bar UDA.

This value does not affect the length of the reinforcing bar. You need to add this value in your drawings and reports to get the correct length if required.

Method

Type

Product

Code

Thread type

Free distance 1

Free text 2

UDAs written to the reinforcing bars.

You can set the reinforcing bar end method and the coupler type, and add a product name and a code for reporting purposes.

The used attribute name depends on which end of the reinforcing bar the coupler was created.

Note:

The above user-defined attributes affect numbering. Reinforcing bars with different attribute values get different part marks.

Coupler attributes tab

Use the Coupler attributes tab to define user-defined attributes (UDAs) for couplers or end anchor parts. For each UDA, you can select to inherit the value from the rebar or the cast unit. To enter a value, select the inherit option None.

Note that if the cast unit does not have any value for that particular UDA, the value is taken from the main part of the cast unit. By default, you can enter a Comment and values for User field 1 … 4 UDAs. You can customize the set of UDAs by modifying the UDA fields in the RebarCouplers.Udas.dat file, located in the ..\Environments\common\system folder.

Split rebar and add coupler

Split rebar and add coupler splits a reinforcing bar group or rebar set, and adds couplers in relation to the direction of the picked points.

Objects created

  • Circular hollow parts

    The parts connect the two reinforcing bar groups or rebar sets.

Use for

Situation Description

Staggered couplers with split reinforcing bars.

Selection order

  1. Double-click Split rebar and add coupler to open the component properties.
  2. Click Split rebar with coupler.
  3. Select the reinforcing bar, bar group, or rebar set to be split.
  4. Pick the first split point.
  5. Pick the second split point.

    This point defines the line at which the bars are split and couplers are inserted.

  6. Pick the third point.

    This point defines the side of the primary bars. This is needed if the primary and secondary bars have different properties.

  7. Repeat the steps 3 - 6, or press Esc to cancel picking.

Parameters tab

Use the Parameters tab to define the coupler properties.

Option Description
Use manually entered values Enter values for the coupler properties.
Use auto attribute file

The values in the auto attribute file override the coupler component values.

Typically the auto attributes file contains one or more attribute values to be used with certain bar sizes.

Go to Tekla Warehouse to get auto attribute files for your project.

For more information on the structure of the auto attribute files, see Customize attribute files, part mapping and user-defined attributes (UDAs).

Option Description
Use custom component

Select Yes to create the coupler as a custom part.

Select No to create the coupler as a normal part.

Name

Type the name of the custom component, or select it from the Applications & components catalog.

Ensure that the selected component is a custom part.

Attribute

Type the name of the attribute file of the custom component.

The coupler custom part is created using the saved attributes given here.

Input points The order of the start and the end points of the custom component.
Add to rebar assembly

To add the coupler as a sub-assembly to the rebar assembly, select either Yes, to primary bar or Yes, to secondary bar. These options will create new rebar assemblies for the new bars created by the split command.

The default value is No.

Option Description
Numbering series Prefix and a start number for the coupler part position number.

In the Inherit from list, select which numbering settings are used for couplers.

  • With None, enter the part and assembly prefix and start numbers.

  • With Rebar, the numbering settings of the primary bars are used.

  • With Cast unit, the cast unit numbering settings are used.

Attributes Name, diameter, material, finish and class of the coupler parts.
Staggered type
  • None

    Couplers are placed along the two picked points.

  • Left

    Couplers are placed to the left side of the two picked points.

  • Right

    Couplers are placed to the right side of the two picked points.

  • Middle

    Couplers are placed on both sides of the two picked points.

The overall end-to-end length of the coupler.

If you use a custom part, this is the length between the start point and end the point of the custom part.

Coupler position

Location of the couplers in relation to the selected split line.

If you select the Left or the Right option, the actual left or right depends on the third input point which defines the side of the first bar.

This option is available only when there is no staggering.

Example:

When you create the couplers as custom parts, the properties in the Numbering series and Attributes sections can be filled from the custom part settings if you have named the properties in a certain way. For an example, see Customize attribute files, part mapping and user-defined attributes (UDAs).

Rebar attributes tab

Use the Rebar attributes tab to define the user-defined attributes (UDAs) for rebars.

Option Description
Threaded length

The value is written to the reinforcing bar UDA.

The fields are used for checking which bars have threads and what are the thread values so that they can be shown in drawings and reports.

Extra fabrication length

This value is written to the reinforcing bar UDA.

This value does not affect the length of the reinforcing bar. You need to add this value in your drawings and reports to get the correct length if required.

Method

Type

Product

Code

Thread type

Free distance 1

Free text 2

UDAs written to the reinforcing bars.

You can set the reinforcing bar end method and the coupler type, and add a product name and a code for reporting purposes.

The used attribute name depends on which end of the reinforcing bar the coupler was created.

Note:

The above user-defined attributes affect numbering. Reinforcing bars with different attribute values get different part marks.

Coupler attributes tab

Use the Coupler attributes tab to define user-defined attributes (UDAs) for couplers or end anchor parts. For each UDA, you can select to inherit the value from the rebar or the cast unit. To enter a value, select the inherit option None.

Note that if the cast unit does not have any value for that particular UDA, the value is taken from the main part of the cast unit. By default, you can enter a Comment and values for User field 1 … 4 UDAs and Layer. You can customize the set of UDAs by modifying the UDA fields in the RebarCouplers.Udas.dat file, located in the ..\Environments\common\system folder.

Rebar end trimming

Rebar end trimming adjusts the space between two reinforcing bar ends.

Use for

Situation Description

Space between reinforcing bar ends.

Selection order

  1. Select the couplers you want to modify.
  2. Modify the properties.
  3. Click Apply to selected couplers.

OR

  1. Modify the properties.
  2. Click Select rebars.
  3. Select the reinforcing bars whose ends are adjusted according to the value set for the gap.

Rebar coupler/Rebar end anchor tab

Option Description
Get free gap from auto attributes file

Select Yes if you want to use the gap defined in the Auto attribute file for the couplers. When you select Yes, only the coupler components that have the Use auto attribute file in use are adjusted.

See Customize attribute files, part mapping and user-defined attributes (UDAs).

Select No if you want to manually enter the free gap.

The gap when Get free gap from auto attributes file is set to No.
Trim both bars Select which of the reinforcing bars is modified.
Apply to selected couplers Select the couplers you want to modify and click the Apply to selected couplers button to adjust the bars according to the value set for the gap.
Select rebars

Click the Select rebars button and select the reinforcing bars whose ends you want to adjust according to the value set for the gap.

The reinforcing bar ends need to be close to each other.

Update rebar attributes

Use Update rebar attributes to manage the user-defined attributes (UDAs) of the couplers and the end anchor parts created by the Rebar Coupler and Anchor Tools. With Update rebar attributes you can check the current values of the selected reinforcing bars or all reinforcing bars.

If you have added coupler or end anchor components to reinforcing bars, the UDA values are controlled by the coupler or the end anchor components and their properties. If you delete the coupler or the end anchor component, the UDAs defined by those components are not cleared automatically. Use Update rebar attributes to clear the obsolete attribute values.

Option Description
Selected The values of all coupler and end anchor UDAs of the selected reinforcing bars in the model.
All The values of all coupler and end anchor UDAs of all reinforcing bars in the model.
Update

Deletes the values of all coupler and end anchor UDAs of all reinforcing bars on the selected rows.

Only the obsolete coupler UDAs of the reinforcing bar are deleted.

You can select multiple rows by holding down Ctrl or Shift.

Update (phase only)

Updates the phase values of the coupler and end anchor parts so that the phase values are the same as the phase values of the related reinforcing bars.

Show only rebar with attributes

Select this check box if you want to show only reinforcing bars that have values in their coupler or end anchor UDAs.

After you have selected the check box, click Selected or All to refresh the table.

Customize attribute files, part mapping and user-defined attributes (UDAs)

Auto attribute files

The attribute table files are text files that can locate in any of the system folders, or in a model folder. You can have as many attribute table files as you need. There are different attribute tables for end anchors (one input reinforcing bar) and coupler components (two input reinforcing bars). The extensions for attribute table files are

  • .couplers.csv for Rebar coupler and Split rebar and add coupler components

  • .anchors.csv for Rebar end anchor component.

The attribute table contains a header line, including the column names and one or more table rows containing the attribute values. Columns are either selector columns or attribute columns.

The selector column names are Primary.Size, Primary.Grade, Secondary.Size, and Secondary.Grade.

The attribute columns contain the attribute value that is the name given in the header row. The component attribute values given in the table row are used whenever the component input (primary + secondary for Rebar coupler and secondary for Rebar end anchor) matches with the selector values.

Go to Tekla Warehouse to get auto attribute files for your project.

Custom part mapping

When you create the coupler or the end anchors as custom parts, the properties in the Numbering series and Attributes sections can be filled from the custom part settings if you have named the properties in a certain way. The following example shows the mapping between the Numbering series and Attributes properties and the custom part properties.

User-defined attributes (UDAs)

You can customize the content of the Attributes tab and the UDAs in the Rebar Coupler and Anchor Tools components.

The UDAs are defined in a text file named RebarCoupler.Udas.dat, located in the ...\ProgramData\Trimble\Tekla Structures\<version>\Environments\Common\system folder. The file can also be placed in some other system folder or in a firm folder. Note that the file is not read from the model folder.

The RebarCoupler.Udas.dat file only defines which UDAs are shown on the Attributes tab. If you modify the file, include only existing UDAs to the file. If you want to create new UDAs, ensure that you define them properly.

Note:

The UDAs affect numbering if the UDAs' special numbering flag (special_flag) is set to yes in the objects_couplers.inp file. Reinforcing bars with different UDA values will then get different part marks.

Oliko tästä apua?
Edellinen
Seuraava