2024 SP3: Mejoras y correcciones importantes

Tekla Structures
Modificado: 9 Sep 2024
2024
Tekla Structures

2024 SP3: Mejoras y correcciones importantes

Puede encontrar la última versión de servicio de Tekla Structures y los instaladores de entorno actualizados en Tekla Downloads.

Descargue Tekla Structures

Corrección principal: Nuevos colores RGB personalizados para líneas patrón

Ahora también puede aplicar colores RGB personalizados a las líneas patrón que añada en los dibujos mediante el comando Línea patrón. Las líneas patrón son líneas especiales y complejas que puede crear y aplicar a los dibujos de un modo sencillo. Haga clic en el botón Examinar de las Propiedades línea patrón y seleccione un color de la paleta de colores personalizados para usar colores personalizados al añadir líneas patrón.

Los colores personalizados están disponibles para seleccionarlos cuando añade líneas patrón en el dibujo utilizando el comando Línea patrón, pero no cuando crea los patrones de línea en Editor línea patrón.

TSAC-8332

Mejora de la usabilidad de las configuraciones detalladas a nivel de objeto

Cuando se añaden nuevas reglas a las configuraciones detalladas a nivel de objeto mediante el botón Añadir fila y se ha seleccionado una fila, la nueva regla se añadirá ahora después de la fila seleccionada. Anteriormente, la nueva regla siempre se añadía en último lugar en la lista de reglas y era necesario utilizar los botones Mover arriba y Mover abajo para colocar la regla en la posición deseada en la lista.

TTSD-63331

Mejoras en componentes de acero

Placa base (1004)

En la pestaña Anclajes, ahora es posible especificar una clase para la lechada.

TSAC-8407

Placa base (1042)

En la pestaña Anclajes, ahora es posible especificar una clase para la lechada.

TSAC-8406

Rigidizadores (1003)

Ahora puede seleccionar en la pestaña Parámetros si el componente busca partes de entrada creadas como compuestos de partes soldadas.

TSAC-8496

Correcciones

Número de defecto Área de desarrollo Descripción
TSAC-8153 Concrete components

Wall to wall connection: Shortening the wall now works correctly again.

TSAC-8210 Concrete components

Embedded anchors (008): Previously, reading anchors from a configuration file was available only for custom part type of anchors. Now this is available also for custom detail and connection type of anchors.

TSAC-8420 Concrete components

Reinforced concrete stair (95): Creating only the bottom group of rebars now works correctly for top and bottom landing stirrups.

TSAC-7856 Steel components

Shear plate simple (146): The Clearance of cut from web setting on the Notch tab now works correctly when the XS_ALLOW_SHEAR_PLATE_CLASH_FLANGE advanced option is set to TRUE.

TSAC-8157 Steel components

Shear plate to tube column (47): Previously, the slot through the main part was not created correctly when the shear tab was sloped. This issue has now been fixed.

TSAC-8192 Steel components

Tube gusset (20): Previously, when the secondary parts were located on both sides of the main part, the weld between the gusset and the main part was created incorrectly. This issue has now been fixed.

TSAC-8225 Steel components

Beam to column web connections: Previously, the advanced option XS_STANDARD_STIFFENER_WIDTH_TOLERANCE was used also for partial width stiffeners. This issue has now been fixed.

TSAC-8467 Steel components

Tube gusset (20): Previously, an incorrect distance between the main part and the connection plate was used in some situations. This issue has now been fixed.

TSAC-8480 Steel components

Tube gusset (20): It is now possible to define the gusset plate location when the secondary parts are located on both sides of the main part.

TSAC-8486 Steel components

Simple base plate 2 (1031): Previously, the weld between the key profile and the base plate was not created correctly. This issue has now been fixed.

TSAC-8489 Steel components

Shear plate simple (146): Previously, the cut for bolt clearance was created also when it was not needed. This caused problems with numbering. Now this issue has been fixed.

TSAC-8493 Steel components

Joist seat (58): Previously, the prefix and start number for the part position number of the bottom shear tab was not correctly applied. This issue has now been fixed.

TSAC-8512 Steel components

Cold rolled overlap (1): Previously, stays were created incorrectly if the sum of the main and secondary part heights was higher than 1800 mm. This issue has now been fixed.

TSAC-8528 Steel components

Railings (S77): Previously, setting the maximum length of the bottom rail to 0.0 caused Tekla Structures to stop working. This issue has now been fixed.

TTSD-45368 Import, export, interoperability

Export to Tekla Structural Designer: In the analysis model export from Tekla Structures to Tekla Structural Designer, concrete parts are now exported using the same rules as steel parts.

  1. The analysis axis of each part in Tekla Structures is used as the insertion line in Tekla Structural Designer.
  2. The Tekla Structures part position is mapped to the Tekla Structural Designer alignment.
  3. The major and minor offsets are adjusted in Tekla Structural Designer to get the member in the correct place.
TTSD-63344 Import, export, interoperability

Export drawings as DWG/DXF/DGN: Drawing export rule settings are now displayed and loaded faster.

TTSD-63401 Import, export, interoperability

IFC export: You can now export string type UDAs longer than 80 characters to IFC files.

TTSD-64002 Import, export, interoperability

Tekla Structures stopped responding when reading an invalid IFC export property set file. This issue has now been fixed.

TTSD-63060 Templates and reports

Drawing layout tables: The line width was not always correct in drawing tables. This issue has now been fixed.

TTSD-63682 Templates and reports

Custom inquiry: Earlier, when using a formula with a property whose value was very close to zero and so small that scientific format was needed (for example, 5.4*10-8), the value of the formula was not shown correctly in Custom inquiry. This issue has now been fixed.

TSAC-8479 Drawings

Rebar pull-out picture and marking: Now all of the mark content is updated automatically. Earlier, if the mark contained a UDA, for example REBAR_SEQ_NO, and you changed the value of the UDA in the model without making any other modifications to the rebar, the UDA value in the mark was not updated and was still showing the old value, and you had to update the mark manually.
NOTE: The fix was technically implemented so that the mark creation now uses associative note instead of plain text. As a side effect of this, the vertical alignment of the elements in the mark content has changed from center aligned to bottom aligned.

Image
Rebar mark improvement
TTSD-21818 Drawings

Earlier, when you created an unfolded single part drawing of a polybeam that had cuts, the bending lines were not placed correctly in the center of the cuts. When the polybeam profile did not have a prefix, the bending line was not shown at all. These issues have now been fixed.

TTSD-60565 Drawings

Earlier, when you created an unfolded single part drawing of a polybeam that had cuts, the bending lines were not placed correctly in the center of the cuts. This issue has now been fixed.

Image
Bending line
TTSD-64028 Drawings

When selecting a new symbol in the drawing property pane, the symbol index number was not automatically updated to reflect the new selection in the Mark content - symbol dialog box. This issue has now been fixed.

TTSD-64048 Drawings

Sometimes drawing view properties did not fully load, resulting in the loss of settings such as mark leader line arrowheads. This issue has now been resolved, and drawing view properties now load correctly.

TTSD-64064 Drawings

Drawing cloning: The section views are now handled better in drawing cloning. For example, the logic for updating and cloning the views was improved.

TTSD-64333 Drawings

Drawing text objects in property pane: The down arrow is now supported in the property pane when editing the text of the text object.

TTSD-64346 Drawings

Earlier, when using the PROFILE attribute in drawing view titles, the shape GUID was shown instead of the shape name for items. This issue has now been fixed.

TTSD-64473 Drawings

Part reference lines: The Color property box for reference lines now shows the correct color in the Part Properties dialog box. Earlier, the Color property box was blank. 

TTSD-62968 System and options

standard.*.more files are now again available in the Common and Default environments. This fixes an issue where standard file loading did not clear the values of the user-defined attribute dialog box when the dialog box was already open.

TTSD-63193 Tekla Model Sharing

Tekla Model Sharing: Previously, when you wrote out, the error message for a locked file did not contain the correct reason. This has now been fixed.

TTSD-64338 Reinforcement

Rebar sets: An issue has been fixed that would cause layering problems with slightly inaccurate rebar set leg faces.

TTSD-58840 Modeling

BCF Topics: Previously, some top views created in Trimble Connect were rotated 90 degrees when they were loaded in Tekla Structures. This has now been fixed.

TTSD-63863 Modeling

Now, when you copy properties in the property pane, the property pane does not reset the possible manual modifications that you have done.

TTSD-64062 Modeling

Previously, clip plane edges were not visualized in cases where there were front facing faces behind the edge of a back facing clipped face. This has now been fixed.

TTSD-64118 Modeling

Previously, if the base curves of lofted plates had a small difference on the border of accuracy that Tekla Structures uses, opening models with such plates caused Tekla Structures to be unexpectedly closed. This has now been fixed.

TTSD-64143 Modeling

BCF Topics: Now, you can link objects to a topic and view the linked objects both in Trimble Connect and Tekla Structures when you are working with both the .tekla and .ifc files.

TTSD-64269 Modeling

Previously, if you used the Clip references only option to create clip planes, the clip plane was also clipping the part edge lines when their representation was only the Level Of Detail (LOD) stick in the zoomed out view. This has now been fixed.

TTSD-64369 Modeling

Previously, when copying objects using numerical input and not using the dialog box, the copying was done with respect to copy origin. This has now been fixed, and the copying is done with respect to the last copy, as in previous Tekla Structures versions. When you pick points, the dimensions are now also shown with respect to the last copy or the last picked point.

This fix reverts TTSD-56113, which was released in Tekla Structures 2024 SP2.

TTSD-64004 Analysis and design

Import from Tekla Structural Designer: While importing analysis results from Tekla Structural Designer to Tekla Structures, some incorrect warnings were shown in the process log. This issue has been addressed and corrected now.

TTSD-63941 Tools and components

Macros: Some recorded keystroke macros did not work. This issue has now been fixed.

TTSD-64394 User interface

Property pane: The Expand all button in the Property pane settings now works.

TSAC-8415 Import, export, interoperability (concrete)

BVBS export: Rebar groups modeled as normal groups are no longer processed as tapered.

TSAC-8527 Import, export, interoperability (concrete)

Export Unitechnik (79): Searching for the embed name in the Special export assembly file name field is no longer case sensitive. Previously, if you used a different case in the search than what the file had, the file was not found.

TSAC-8539 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Previously, skewed cuts at the start or at the end of the hollowcore profiles caused incorrect length of the exported hollowcore profile. This issue has now been fixed.

TSAC-8542 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Previously, edge cuts at the start or at the end of the hollowcore profiles caused incorrect length of the exported hollowcore profiles. This issue has now been fixed.

¿Le ha resultado útil?
Anterior
Siguiente