Braced girder (88): Previously, the braced girder was not split and it did not continue when it reached the recesses. This issue has now been fixed.

Concrete console (110): The polygon cut to cut the column is now created properly with sloped beams.

Concrete console (110): Previously, the hole position was not correct in the neoprene when it was placed under a sloped beam. This issue has now been fixed.
 

Corbels and recesses (82): Recess positioning for cut parts has been improved.

Braced girder (88): Previously, girders were not created correctly if there was a cutout or a partial cutout on one or both of the side edges of the main part. This issue has now been fixed.
 

Rebar coupler and anchor tools: The Extra fabrication length values are now written to the correct user-defined attributes.

Electric box in wall (84): Sometimes, when you changed the connection used between the electric parts and the panel, the result assembly of the parts was broken. This issue has now been fixed.
 

Concrete foundation (1030): The height level of the inner tube rebar is now properly defined.

Embedded anchors (008): Numbering now works properly for the extra insulation part.

Lifting anchor (80): Previously, lifting anchors were not created properly when created on an inconsistent assembly. This issue has now been fixed.

Wall to wall connection: Connectors are now placed correctly.

Embedded anchors (008): Earlier, when using a component for creating anchors in the Embedded anchors (008) component, there could be an application error in Tekla Structures. This issue has now been fixed.

Haunch (40): Main part stiffeners are now created correctly when the column profile has flange slope ratio.

Stiffened end plate (27): The default value of the front plate height is now the same as the end plate height in the column to beam connections.

Railings (S77): Previously, only 99 vertical rails were welded to the main part. This issue has now been fixed and all rails are welded correctly to the main part.

Stiffeners (1003), Multiple stiffeners (1064): Previously, weld preparations were always created. This issue has now been fixed.

Seating cap plate (2): Previously, the horizontal offset of the lower cap plate was not correctly applied. This issue has now been fixed.

Clip angle (141): Previously, the vertical bolt edge distance was not correctly applied in some cases. This issue has now been fixed.
 

Column with stiffeners W (182): Previously, the strip to the secondary part flange did not work when the secondary part was connected to the main part web. This issue has now been fixed.

UltraZED File transfer (93): Previously, manually adjusting the length of a diagonal restraint after they had been inserted with a component resulted in incorrect CAM data as it would not update. Now, the Tekla Structures displays a warning message, and requests drawings.

Ayrshire Diagonal tie - column (81), Ayrshire File transfer (92): Previously, there was an application error when connecting the diagonal brace to a column or rafter. This issue has now been fixed.

The Auto bolt component used in custom components now supports the following data types for the BoltSize attribute: bolt size, length, double, and string. The component can also be modified while being a part of custom component, in the user interface, without any unexpected results. The stand-alone Auto bolt component works the same way as previously.

Steadmans Mezzanine inset cleat (121) is a new inset cleat connection for the mezzanine floor range of beams.

CMF Side rail supports (28): Previously, when using CMF Non-continuous rail (106) to attach rails in between the column webs, if the cut back of the cold rolled was too great, CMF Side rail supports (28) was not applied. This issue has now been fixed.

Tensioner (7): Previously, the component did not work correctly for one secondary part. This issue has now been fixed.
 

Ayrshire Eaves beam to stanchion (113): The Welds tab for this component has been removed.

Two sided clip angle (143): Previously, the vertical position of bolts was affected by the notch cuts in the secondary parts. This issue has now been fixed.

BW Mezzanine floor connection (39): Previously, the default profile used was incorrect, and the cleat thickness option did not work. These issues have now been fixed.

Shear plate simple (35): Previously, the assembly position and start number were incorrectly applied for the shear tab. This issue has now been fixed.

Seating (39): Previously, only one pair of stiffeners was created for some of the main part profiles. This issue has been fixed, and two pairs of stiffeners are now created.

Joining plates (14): Previously, when the angle between the main and secondary part was small, the component did not work correctly. This issue has now been fixed.

Clip angle (141): Previously, the vertical position of bolts was affected by the notch cuts in the secondary part. This issue has now been fixed.

Stiffened end plate (27): On the Parts tab, you can now select whether the front plate is moved in column to beam connections.

U.S. Base plate (1047): Previously, the cuts to create finger shim plates were not positioned correctly. This issue has now been fixed.

Organizer object group (.OrgObjGrp) files can now be read from the subfolders of firm or project folders in the Organizer category properties dialog box.

IFC2x3 export: Due to some invalid fittings, the IFC2x3 export behaved incorrectly when trying to apply these fittings in a certain base point use case. Now invalid fittings are ignored in the IFC2x3 export.

Import from Tekla Structural Designer: Concrete grade 2500 psi is now included in the Tekla Structural Designer import material mapping. It is imported with the warning "Materials were auto-created: 2500 Concrete".

Where Tekla Structures 2022 SP6 and Tekla Structural Designer 2022 (any service pack) were installed on the same computer and the direct link was used for importing or exporting, the import or export process failed.
This issue has now been fixed in this service pack for Tekla Structures. There is no need to install a different service pack for Tekla Structural Designer 2022.

Point clouds: The point cloud location was not modified and saved correctly in a specific use case, which has now been fixed.

The following missing IFC entities have been added in the IFC entity list and in the IFC4 and IFC2x3 export:
IfcBeam (added for assemblies, cast units, and pour units)
IfcChimney (added for assemblies, cast units, and pour units)
IfcColumn (added for assemblies, cast units, and pour units)
IfcFooting (added for assemblies, cast units, and pour units)
IfcMember (added for assemblies and cast units)
IfcPile (added for assemblies, cast units, and pour units)
IfcPlate (added for assemblies and cast units)

IFC4 export: Boolean type (TRUE/FALSE) of user-defined attributes are now exported correctly.

IFC4 export: With the Export flat wide beams as plates setting, plates were sometimes exported to wrong location. This issue has now been fixed.

The IFC4 API in 2022 was changed in 2022 SP6 (IFCExportFlags), which needed a rebuild of the external applications executing the IFC4 export. This change is now reverted so that the external applications work again without the need of a rebuild.

IFC object conversion: The conversion results are now better with certain IFC models containing nested IFC boolean results (adds or cuts).

Trimble Connect: Property sets for rebar sets were previously not exported to Trimble Connect when you used the Upload model command. This issue has now been fixed.

Template Editor: When you panned the template work area with the mouse, the selection handles were drawn with the background color and the handles were invisible. This issue has now been fixed.

CUSTOM.HC_SAWINGS_END_N now returns the correct number of individual sawing lines for the end cuts at every angle.

Tekla Structures stopped responding when a template tried to output a single row that was defined to use columns that started from bottom left or bottom right. This issue has now been fixed.

View-specific dimensioning: The drawing dimensioning method Filter did not work correctly in skewed cases when dimensioning custom components as secondary objects. This issue has now been fixed.

View-specific dimensioning: When the dimensioning method Filter was used for skewed edges and the cast unit consisted of several parts, the dimension start and end points were not always placed correctly. This issue has now been fixed.

View-specific dimensioning: The Filter dimensioning option Only objects on the selected sides did not work when the secondary parts contained cuts, and the filter did not contain an Object type row. This issue has now been fixed.

Drawing dimensioning now works in a rebar assembly that is added to a hierarchical cast unit, for example, to a double wall. Previously, no dimensions were created.

View-specific dimensioning: The dimensioning method Filter with the rule option Only objects on the selected sides did not work for bolt groups. This issue has now been fixed.

Fabrication drawings: The Creation review dialog box now remembers the states of the check boxes better.

Fabrication drawings: The Creation review dialog box now handles the existing drawings more reliably.

Fabrication drawings: The Creation review dialog sometimes showed the same drawing settings twice. This issue has now been fixed.

Adding an associative note for the selected part did not work correctly if you picked the leader line positions outside the drawing view. This issue has now been fixed.

Drawing context menu: Now the context menu in drawing mode is updated and shown correctly when you click the model view while editing a drawing and then return to back to the drawing. Earlier, the context menu was empty in this case.

Earlier, in neighbor parts with bolt holes, circular holes could get a slotted hole mark. This issue has now been fixed.

Earlier, when inserting or modifying marks with the advanced option XS_ENABLE_REBAR_MARK​_LEADER_​LINE_BASE_​​POINT​_OPTIMIZATION set to TRUE, the base point optimization was also done for other types of marks than rebar marks. This issue has now been fixed.  

Print drawings using Printer Catalog printer instances (old printing): Printing in gray scale now works.

Fabrication drawings: The Creation review dialog box was listing some setting files that were not drawing setting files. This issue has now been fixed.

Fabrication drawings: Sorting by multiple columns now works in the Creation review dialog box.

Now, in Tekla Model Sharing, drawing files are restored if the .dg files have been accidentally deleted. Deleted drawings are copied to the ModelSharing\BackUpEnv folder and are checked against to the drawings on the Drawing list. The .dg files are read automatically from the BackUpEnv folder when another user reads in the packet that has been written out after the drawing deletion.

Previously, reading in the sharing changes was sometimes extremely slow if the model contained a large number of custom components that had been duplicated from plugin components with an identical name. A warning dialog box was shown, and you had to click the OK button multiple times on the dialog box to pass the warnings and being able to continue.

Now, the components are no longer automatically updated when you read in. This results in faster performance and fewer false modification conflicts, and no warnings are shown. 

Rebar sets: The commands Create 3D view and Zoom now work properly with rebar set modifiers. The work area around the selected rebar set modifier is now defined correctly.

Rebar sets: You can no longer use the By guidelines command with pour objects or add leg surfaces to existing rebar sets in pour views.

Rebar sets: When Follow edges was set to Yes, bars were not created to all faces of a part if the part collided slightly with another part. Tekla Structures was not able to find suitable edges to follow in these cases. This issue has now been fixed.

Rebar sets: If you switch the work plane from the global origin and then create rebar sets using the By guidelines command, the current work plane is now taken correctly into account and the rebar sets are placed correctly.

Rebar sets: It was not possible to create a modifier or secondary guideline with more than two points in multi-point picking mode if Follow edges was set to Yes. This issue has now been fixed.

Previously, if multiple parts were selected and one of the parts had a parametric profile, the profile was shown as invalid in the property pane. This now has been fixed.

Previously, in some rare cases, when assemblies with and without bolt holes were compared, Tekla Structures might have stopped working unexpectedly. This has now been fixed.

Previously, when modeling and then inquiring negative hole tolerances, the HOLE_TOLERANCE template attribute returned 0 instead of the actual value. This issue has now been fixed.

Previously, if you tried to cut surface treatment by the part it was attached to, Tekla Structures might have unexpectedly stopped working. This issue has now been fixed.

Earlier, when performing operations that required unfolding of lofted plates consisting of several close to parallel polygon sections, for example, inquiry or export to IFC4, there was an application error in Tekla Structures. This issue has now been fixed.

When using Building hierarchy in the model, the Fit work area to selected parts context menu command now correctly zooms to parts when the selection is done with Ctrl+A.

Previously, in some rare situations, Tekla Structures might have stopped working unexpectedly when pressing F1. This has now been fixed.

The ribbon menu commands for Create fabrication drawing are now correctly disabled if there is no model open.

NC/DSTV: Certain weld preparations were not created correctly for I beam flanges when the flange had cuts that made the ends non-rectangular. Now the weld preparations are created correctly in this case.

Export ELiPLAN file (68): Now height is also exported for user-defined profiles.

Export ELiPLAN file (68): Previously, the export of elements with complex geometry did not work correctly. This issue has now been fixed.