Bolted gusset (196)

Bolted gusset (196) connects 1 to 10 braces to a beam or column using a gusset plate, which is bolted or welded to the beam or column. The braces are bolted to the gusset plate. Clip angles can be created either at the ends of the braces, or on each side.

Objects created

Gusset plate
Clip angles or shear tabs (optional) that connect the gusset plate to the beam or column
Clip angles (optional) that connect the brace to the gusset plate
Connection plates
Seal plates (hollow braces)
Stiffeners (optional)
Bolts
Welds
Cuts

Use for


Situation	Description
	Brace profile: RHS Gusset plate is bolted to the beam flange using a clip angle. Braces are slotted around the gusset plate and attached to it using bolts and clip angles.
	Brace profile: Tube Gusset plate is welded to the beam web. Brace is notched around the gusset plate and pinned to it.
	Brace profile: T Gusset plate is welded to the beam flange. Brace is bolted to the gusset plate.
	Brace profile: L Gusset plate is welded to the column flange. Brace is bolted to the gusset plate.

Before you start

Create a beam or column, and 1 to 10 braces.

Selection order

Select the main part (beam or column).
Select the secondary part (first brace).
Select the second secondary part (second brace).
Select the subsequent secondary parts (subsequent braces).
Click the middle mouse button to create the component.

Part identification key



1	Gusset plate
2	Clip angle

Note:

Tekla Structures uses values in the joints.def file to create this component.

Picture tab

Use the Picture tab to define the dimensions that control the position and shape of the gusset plate.

Dimensions


	Description
1	Define the gap distance between the gusset plate edge and the main part.
2	Define the gusset plate corner angle (in degrees). This value affects the gusset plate shape.
3	Define the length of the edge of the gusset plate. This value affects the gusset plate shape.
4	Define the distance between the braces.
5	Define the distance between the main part and the brace.
6	Define the distance between the clip angle or connection plate edge and the gusset plate edge.

Note: The following examples show only some of the available options. You will find more options on the Picture tab.

Gusset plate positioning

Define how the gusset plate is positioned when a base plate is used.


Option	Desription
	Default Gusset plate is parallel to the main part. AutoDefaults can change this option.
	Gusset plate is parallel to the brace.

Gusset plate chamfer

Define the gusset plate chamfer type and dimensions, and the angle limit for parallel bracing.


	Description
1	Distance between the connection plate and the inner flange of the main part.
2	Horizontal distance between the gusset plate edge and the flange of the main part.
3	Horizontal dimension of the chamfer. By default, the second chamfer is not created.
4	Vertical dimension of the chamfer. By default, the second chamfer is not created.

Cut size

If the gusset plate runs through the main part, define the size of the cut created for the gusset plate.


	Description
1	Define the horizontal size of the cut.
2	Define the vertical size of the cut.

Gusset tab

Use the Gusset tab to control the gusset plate properties, shape and position, clip angle properties and orientation, and angle limit for parallel bracing.

Plates


Option	Description
Gusset	Thickness, width and height of the gusset plate.
Connection plates	Thickness and width of the connection plate.
L profile	Select the clip angle profile from the profile catalog.


Option	Description	Default
Pos_No	Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number.	The default part start number is defined in the Components settings in File menu > Settings > Options.
Material	Material grade.	The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.
Name	Name that is shown in drawings and reports.

Note: The following examples show only some of the available options. You will find more options on the Gusset tab.

Gusset plate connection

Define how the gusset plate is connected to the main part.


Option	Description
	Default Gusset plate is welded directly to the main part. AutoDefaults can change this option.
	Gusset plate is connected to the main part with clip angles. Select to which side of the gusset plate the clip angles are created.
	Gusset plate is connected to the main part with a connection plate. Select to which side of the gusset plate the connection plate is created.

Clip angle orientation

Define how the clip angle is placed on the connection.


Option	Description
	Default Clip angle is placed on the connection so that the longer leg is connected to the gusset plate. AutoDefaults can change this option.
	Clip angle is placed on the connection so that the longer leg is connected to the main part.

Gusset plate shape

When you select the option to optimize the gusset plate weight, you can define whether the selection order of the braces affects the position of the braces.


Option	Description
	Default AutoDefaults can change this option.
	This option optimizes the gusset plate weight.

Brace position


Option	Description
	Default The brace position is not affected. AutoDefaults can change this option.
	The first selected brace is placed closest to the main part.

Gusset plate position on the brace

Define where to place the gusset plate on the brace. If needed, you can fine-tune the gusset plate position by moving the gusset plate in the z or in the y direction.


Option	Description
	Default Gusset plate is positioned in the middle of the brace. AutoDefaults can change this option.
	Gusset plate is positioned on the top flange of the brace.
	Define how much the gusset plate is moved in the z direction.
	Define how much the gusset plate is moved in the y direction.

Gusset plate position on the column or beam


Option	Description
	Select the gusset position. The default option is parallel to the brace.

Brace conn tab

Use the Brace conn tab to define the seal plate, brace notch and slot properties.

Seal plate


Option	Description
Seal plate	Thickness of the seal plate.


Option	Description	Default
Pos_No	Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number.	The default part start number is defined in the Components settings in File menu > Settings > Options.
Material	Material grade.	The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.
Name	Name that is shown in drawings and reports.

Brace notch


Option	Description
	Select whether the brace is notched.
	Vertical notch dimension. Horizontal notch dimension. Notch angle.
	Define the plate distance from the brace outer edge.
	Select whether to create bevel cuts at the brace ends or whether to create a square brace end.

Gusset bolts tab

Use the Gusset bolts tab to control the bolt group properties for bolts that connect the gusset plate to the main part, and to control the clip angle attachment.

Bolt group dimensions



1	Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part.
2	Number of bolts.
3	Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.
4	Dimension for vertical bolt group position.
5	Select how to measure the dimensions for vertical bolt group position.
6	Dimension for horizontal bolt group position.
7	Select how to measure the dimensions for horizontal bolt group position.



1	Location where the bolts should be attached.
2	Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part.
3	Number of bolts.
4	Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.

Clip angle attachment type


Option	Description
	Default Both parts are bolted. AutoDefaults can change this option.
	Automatic When the main part is a tube profile, the clip angles are welded to the main part and bolted to the secondary part. Otherwise the clip angles are bolted to both parts.
	Main part is bolted and secondary part is welded.
	Main part is welded and secondary is part bolted.
	Both parts are bolted.
	Both parts are welded.

Bolts on gusset plate

Define whether the gusset plate is connected to the main part with bolts when no clip angles are used.


Option	Description
	Default Bolts are not created in the gusset plate. AutoDefaults can change this option.
	Bolts are created in the gusset plate.

Staggering of bolts


Option	Description
	Default Not staggered AutoDefaults can change this option.
	Not staggered
	Staggered type 1
	Staggered type 2
	Staggered type 3
	Staggered type 4

Bolt basic properties


Option	Description	Default
Bolt size	Bolt diameter.	Available sizes are defined in the bolt assembly catalog.
Bolt standard	Bolt standard to be used inside the component.	Available standards are defined in the bolt assembly catalog.
Tolerance	Gap between the bolt and the hole.
Thread in mat	Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used.	`Yes`

Slotted holes

You can define slotted, oversized, or tapped holes.


Option	Description	Default
1	Vertical dimension of slotted hole.	`0`, which results in a round hole.
2	Horizontal dimension of slotted hole, or allowance for oversized holes.	`0`, which results in a round hole.
Hole type	Slotted creates slotted holes. Oversized creates oversized or tapped holes. No hole does not create holes.
Rotate Slots	When the hole type is Slotted, this option rotates the slotted holes.
Slots in	Part(s) in which slotted holes are created. The options depend on the component in question.

Bolt assembly

The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assembly.

If you want to create a hole only, clear all the check boxes.

To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.

Bolt length increase

Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.

Brace bolts 1 / Brace bolts 2 / Brace bolts 3 tab

Use the Brace bolts 1, Brace bolts 2 and Brace bolts 3 tabs to control the bolts that connect the first, the second, and the subsequent braces to the gusset plate.

Bolt group dimensions


	Description
1	Number of bolts.
2	Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.
3	Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part.
4	Select how to measure the dimensions for vertical bolt group position.
5	Dimension for vertical bolt group position.

Bolt distance

Define the minimum distance from the connection plate bolts to the intersection point of the main part and brace center lines. If a brace is perpendicular to the main part, the distance is measured from the main part center line to the nearest bolts.

Attributes for Tube crossing (22)

With hollow secondary parts, Bolted gusset (196) automatically removes connection objects created between the gusset plate and the hollow secondary part, and then uses the Tube crossing (22) connection between the gusset plate and the hollow secondary part.

To define which property file that Tube crossing (22) uses, go to the Brace bolts 2 tab, and enter the property file name in the Attributes for Tube crossing (22) box.

Staggering of bolts


Option	Description
	Default Not staggered AutoDefaults can change this option.
	Not staggered
	Staggered type 1
	Staggered type 2
	Staggered type 3
	Staggered type 4

Bolt basic properties


Option	Description	Default
Bolt size	Bolt diameter.	Available sizes are defined in the bolt assembly catalog.
Bolt standard	Bolt standard to be used inside the component.	Available standards are defined in the bolt assembly catalog.
Tolerance	Gap between the bolt and the hole.
Thread in mat	Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used.	`Yes`
Site/Workshop	Location where the bolts should be attached.	`Site`

Slotted holes

You can define slotted, oversized, or tapped holes.


Option	Description	Default
1	Vertical dimension of slotted hole.	`0`, which results in a round hole.
2	Horizontal dimension of slotted hole, or allowance for oversized holes.	`0`, which results in a round hole.
Hole type	Slotted creates slotted holes. Oversized creates oversized or tapped holes. No hole does not create holes.
Rotate Slots	When the hole type is Slotted, this option rotates the slotted holes.
Slots in	Part(s) in which slotted holes are created. The options depend on the component in question.

Angle bolts tab

Use the Angle bolts tab to control the bolts that connect the clip angles.

Part


Option	Description
L profile	Select the clip angle profile from the profile catalog.


Option	Description	Default
Pos_No	Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number.	The default part start number is defined in the Components settings in File menu > Settings > Options.
Material	Material grade.	The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.
Name	Name that is shown in drawings and reports.

Bolt basic properties


Option	Description	Default
Bolt size	Bolt diameter.	Available sizes are defined in the bolt assembly catalog.
Bolt standard	Bolt standard to be used inside the component.	Available standards are defined in the bolt assembly catalog.
Tolerance	Gap between the bolt and the hole.
Thread in mat	Defines whether the thread may be within the bolted parts when bolts are used with a shaft. This has no effect when full-threaded bolts are used.	`Yes`
Site/Workshop	Location where the bolts should be attached.	`Site`

Bolt group dimensions


	Description
1	Number of bolts.
2	Bolt spacing. Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.
3	Bolt edge distance. Edge distance is the distance from the center of a bolt to the edge of the part.
4	Define the edge distance between the clip angle and the brace.
5	Select how to measure the dimensions for vertical bolt group position.
6	Dimension for vertical bolt group position.

Clip angle position


Option	Description
	Select the clip angle position.

Stiffeners tab

Use the Stiffeners tab to define the stiffener properties and dimensions.

Parts


Part	Description
Stiffener 1, Stiffener 2	Thickness of the stiffener.


Option	Description	Default
Pos_No	Prefix and start number for the part position number. Some components have a second row of fields where you can enter the assembly position number.	The default part start number is defined in the Components settings in File menu > Settings > Options.
Material	Material grade.	The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.
Name	Name that is shown in drawings and reports.
Finish	Describes how the part surface has been treated.

Stiffener length


	Description
1	Define the distance between the stiffener edge and the gusset plate edge.
2	Define the length of stiffener.

Stiffener dimensions


	Description
1	Define the width of the stiffener.
2	Define the length of the stiffener base.
3	Define the length of the skew part of the stiffener.
4	Define the distance from the stiffener center line.
5	Define the vertical distance between the stiffener base and the skew part.