2022 SP2: Enhanced Timber Design Using Tekla Tedds - New Deflection Checks and Single Column Lift Design

Tekla Structural Designer
2022
Tekla Structural Designer

2022 SP2: Enhanced Timber Design Using Tekla Tedds - New Deflection Checks and Single Column Lift Design

Note: Use of Design using Tekla Tedds in this release requires the installation of the Tedds July Engineering Library Update which is available from Tekla Downloads or via the Update Service.

New Deflection Checks

Building on the Enhancements to Timber Design Using Tekla Tedds added in release 2022 SP1, this release adds a significant further enhancement in the form of comprehensive assessment and checking of member deflections for both Eurocode and US Regional Codes. The new feature includes the option to calculate and include the effects of creep deformation for long term deflection checks.

For more about the overall timber design workflow and how this exciting new feature sits within it, see these new videos: Learn how to design timber members in Tekla Structural Designer using Tekla Tedds (Eurocode) and Learn how to design wood members in Tekla Structural Designer using Tekla Tedds (USA).

With this new feature, deflection checks can now be included in the overall design checks for timber beams, with the specifics of each Regional Code as follows:

  • US Code checks include:

    • Dead, Live, Snow, Wind, and Total loads for instantaneous deflections

    • Total load deflections can optionally consider the effects of creep deformation in design

  • Eurocode checks include:

    • Dead, Imposed, Snow, Wind, and Total loads for instantaneous deflections

    • Total load deflections can optionally consider the effects of creep deformation in design

Key aspects of the new feature are:

New Timber Member Deflection Properties

Comprehensive new deflection limit settings are added for timber members in the same manner as the existing ones for steel members.

  • Just as for steel members, the Deflection limits settings are available via both the Properties Window for selected member(s) and via the individual member properties dialog. They include both relative span/ factor and optional absolute values for each criteria.

New Deflection Functionality in the Tedds Timber Design Calculation

To cater for the new deflection checks, the Tedds Timber Design Calculation is enhanced as follows:

  • Deflection Design Cases - additional deflection design cases are automatically added to the strength design cases for every Tedds design that is created. The load combination that governs the deflection is identified in each deflection design case name.
  • All deflection design cases and properties can be individually viewed and managed from the Deflection criteria dialog within the Tedds interface.

Long term deflections due to creep effects

Optionally you can also include the effects of creep deformation for long term deflection checks.

  • New Design Setting - this is controlled by the new setting “Include long term effects in total load deflection check” in Design Settings > Timber as shown in the pictures below.
  • Long term load ratios/ factors are automatically calculated appropriate to the Regional Code and populated to the Tedds calculation deflection criteria, as shown below.
  • The final deflections are determined in the Tedds calculation and displayed in the preview results as shown below:
  • Automatic adjustment of design deflection value - you can adjust the modulus of elasticity and moment of inertia values in Tekla Structural Designer as you wish, to create the desired distribution of forces in a model. The deflection values used in design are adjusted to determine the relative member deflection value assuming an unfactored moment of inertia and using the Emean value typically recommended for serviceability checks under normal conditions.

New Streamlined Single Column Lift Design

A multi-stack column ‘Lift’ (consisting of several stacks between floors all having the same section size) can now be designed using a single instance of the Tedds timber design calculation for the entire lift. Previously it was necessary to run the calculation separately for each stack, and any change to the section size needed to be manually re-applied at each stack. The new streamlined lift design process can be significantly quicker than the previous one.

  • Note that, while the use of an envelope for the entire lift (as described below) may produce a more conservative design in some situations, any such conservatism can be removed if necessary by specifying splices between stacks (while retaining the same section size above/ below the splice) as required.

Some key aspects of the new design are:

  • Design forces and unbraced lengths - each design case is established using an envelope of the maximum forces in each direction from all stacks in the lift. The major and minor axis unbraced lengths are taken from the longest stack in the lift.
  • Design for Ungrouped/ Grouped columns - for an ungrouped column, design is performed using the enveloped lift forces, after which all stacks in the lift are automatically checked using their individual stack lengths and member forces. For a grouped column, a similar process is followed, other than the design being performed using the enveloped group lift forces, after which all stacks in the group are automatically checked using their individual stack lengths and member forces.
  • Design Process - the design process will depend on whether column grouping is enabled (Design Settings > Design Groups > Timber Beams/ Columns/ Braces) and also on what has been selected for the design.
    • Ungrouped design:
      • Design using Tekla Tedds > Member - with an individual stack selected
        1. The lift containing the selected stack is designed for its LIFT forces.

        2. All stacks in the lift are then checked for their individual stack MEMBER forces.

      • Design using Tekla Tedds > Member - with an entire column selected

        1. All lifts in the column are designed for their LIFT forces.

        2. All stacks in all lifts are then checked for their individual stack MEMBER forces.

      • Design performed from Review Data > Design Summary - by clicking the Results.. button adjacent to a stack

        1. The lift containing the selected stack is designed for its LIFT forces.

        2. All stacks in the lift are then checked for their individual stack MEMBER forces

    • Grouped design:

      • Design using Tekla Tedds > Group

        1. All lifts are designed for the respective lift GROUP forces.

        2. All stacks of all lifts in the group are then checked for their individual stack MEMBER forces.

      • Design using Tekla Tedds > Member - with an individual stack selected

        1. The lift containing the selected stack is designed for its LIFT forces.

        2. All stacks of this lift in the group are then checked for their individual stack MEMBER forces.

        3. The designed lift is also checked for the lift GROUP forces so as to be available for export of group to Tedds.

      • Design using Tekla Tedds > Member - with an entire column selected

        1. All lifts in the column are designed for their LIFT forces.

        2. All stacks in all lifts in the group are then checked for their individual stack MEMBER forces.

        3. The designed lift is also checked for the lift GROUP forces so as to be available for export of group to Tedds.

      • Design performed from Review Data > Design Summary - by clicking the Results.. button adjacent to a stack

        1. The lift containing the selected stack is designed for its LIFT forces.

        2. All stacks of this lift in the group are then checked for their individual stack MEMBER forces.

        3. The designed lift is also checked for the lift GROUP forces so as to be available for export of group to Tedds.

  • Export to Tekla Tedds - a detailed report can be obtained by exporting to Tedds. The result will depend on what has been selected for the export.
    • Export to Tekla Tedds > Member - with an individual stack selected

      • The selected stack is exported with the design performed for the stack MEMBER forces

    • Export to Tekla Tedds > Member - with an entire column selected

      • All stacks in all lifts in the column are exported with the design performed for the stack MEMBER forces

    • Export to Tekla Tedds > Group

      • All lifts in the column are exported with the design performed for their LIFT forces

Was this helpful?
Previous
Next