2022 SP8: Wichtige Verbesserungen und Korrekturen

Tekla Structures
2022
Tekla Structures

2022 SP8: Wichtige Verbesserungen und Korrekturen

Das neueste Tekla Structures Service Pack und die aktualisierten Installationsprogramme für die Umgebung finden Sie unter Tekla Downloads.

Tabellen im Zeichnungslayout ersetzen

Im Kontextmenü Layout-Editor können Sie mit dem neuen Befehl Tabelle ersetzen jetzt im Layout Tabellen ersetzen. Zum Ersetzen einer Tabelle klicken Sie im Layout mit der rechten Maustaste auf die Tabelle und wählen Tabelle austauschen aus.

Beim Ersetzen einer Tabelle werden alle für die ersetzte Tabelle definierten Einstellungen beibehalten. Durch den neuen Befehl müssen Sie nicht erst eine Tabelle im Layout zu entfernen, dann eine neue Vorlage hinzufügen, für diese Ankerpunkt und Ausrichtung festlegen und anschließend andere Tabellen mit der neuen verbinden.

TTSD-41881

Änderung beim Steuern der Sichtbarkeit von Betoniereinheiten im Organizer

Tekla Structures 2022 wurde die Einstellung Betoniereinheiten aktiviert im Organizer eingeführt, die es Ihnen ermöglicht, zu steuern, ob Betoniereinheiten oder Ortbetonbauteile als höchste Ortbeton-Hierarchieebene im Organizer verwendet werden. Die Einstellung Betoniereinheiten aktiviert befindet sich auf der Registerkarte Synchronisation im Organizer Einstellungen.

Ab Tekla Structures 2022 SP8 müssen Sie, um die Einstellung Betoniereinheiten aktiviert nutzen zu können, die erweiterte Option XS_ENABLE_POUR_MANAGEMENT auf TRUE einstellen. Beachten Sie, dass wenn die erweiterte Option XS_ENABLE_POUR_MANAGEMENT auf FALSE eingestellt ist, die EinstellungBetoniereinheiten aktiviert im Organizer nicht angezeigt wird und Sie Betoniereinheiten nicht als höchste Ortbeton-Hierarchieebene im Organizer verwenden können.

Bisher war die Einstellung Betoniereinheiten aktiviert im Organizer Einstellungen unabhängig vom Wert der erweiterten Option immer verfügbar.

TTSD-56158

Referenztext für Schweißnähte kann in benutzerdefinierten Komponenten verwendet werden

Sie können nun Referenztext für Schweißnähte in benutzerdefinierten Komponenten verwenden. Beachten Sie, dass der Referenztext für Schweißnähte nur in einer einzelnen Zeile dargestellt werden kann.

TTSD-33758, TTSD-56526, TTSD-28282, TTSD-45866, TTSD-38478

Verbesserungen im EliPlan-Export (68)

Exportierte Datei öffnen

Sie können jetzt nach Abschluss der Verarbeitung die exportierte Datei über die neue Einstellung Exportierte Datei nach der Verarbeitung öffnen auf der Registerkarte Parameter in der zugehörigen Anwendung öffnen.

TSAC-7381

Automatische Zubehörerkennung nach Form

Sie können jetzt bei Aussparung/Einbauteil plotten mit der Option Automatisch auf der Registerkarte Plotterdaten für das Zubehör automatisch anhand der Form erkennen.

TSAC-7297

Unterstützung für den Export von Bewehrungsbaugruppen

Es wird nun der Export von Bewehrungsbaugruppen unterstützt. Bewehrungsbaugruppen werden als Grenzrahmen exportiert.

TSAC-5228

Verbesserungen im Unitechnik-Export (79)

Sie können nun über die neue Einstellung Austauschen von Schalen zulassen auf der Registerkarte TS Konfiguration das Austauschen von Doppelwandschalen spezifizieren.

TSAC-6605

Neue erweiterte Optionen für überdimensionierte Schraubenlöcher

Sie können jetzt die folgenden erweiterten Optionen nutzen, um den Inhalt des Elements Größe in Bezeichnungen für große Schraubenlöcher zu definieren. Für Werkstatt- und Baustellenlöcher sowie für Fertigungs- und Übersichtszeichnungen stehen separate erweiterte Optionen zur Verfügung.

  • XS_SHOP_OVERSIZEDHOLE_MARK_STRING_FOR_SIZE

  • XS_SHOP_OVERSIZEDHOLE_MARK_STRING_FOR_SIZE_IN_GA

  • XS_SITE_OVERSIZEDHOLE_MARK_STRING_FOR_SIZE

  • XS_SITE_OVERSIZEDHOLE_MARK_STRING_FOR_SIZE_IN_GA

TTSD-56128

Korrekturen

Mängelnummer Entwicklungsgebiet Beschreibung
TSAC-5999 Concrete components

Concrete console (110): On the Parameters tab, you can now cut the beam part around the column. Previously, you could only cut the column.

TSAC-6856 Concrete components

Floor layout: The Line up direction setting on the General tab now works correctly. Previously, if you had the insulation layer as the lower layer and changed the line up direction, the insulation was not created correctly.
 

TSAC-7019 Concrete components

Floor layout: The CIP filler part is no longer created outside the component polygon boundaries.

TSAC-7327 Concrete components

Automatic splicing tool: Single bars are now correctly split and spliced regardless of their direction. Previously, single vertical bars were not handled correctly.

TSAC-7339 Concrete components

Rebar end anchor now correctly creates end detail modifiers for rebar sets in cases where only one bar is affected.

TSAC-5598 Steel components

Two sided clip angle (143): Previously, the flange cut created due to bolts clashing with the flange was not created for the second secondary beam in all situations. This issue has now been fixed.

TSAC-6355 Steel components

Ring plate: The part and assembly start number of the ring plate are now modified when only the corresponding check boxes are selected. Previously, the part and assembly start number were not modified unless all the check boxes in the dialog box were selected.

TSAC-6356 Steel components

Opening frame: The On plane and At depth offset values on the Parts tab for top frame, bottom frame and vertical posts are length values and they now use the correct units set in Options > Units and decimals. The Angle value for welds and Rotation angle on the Parts tab are angle values and they now use the correct units set in Options > Units and decimals.

TSAC-6400 Steel components

Two sided end plate (142): Previously, safety connections were not correctly applied in all situations. This issue has now been fixed.

TSAC-6652 Steel components

Gusseted cross (62): Previously, the bolt edge distance on the bracing side was not correctly applied from the joints.def file. This issue has now been fixed.

TSAC-7082 Steel components

Cast-in plate (1069): Previously, the tab plate material was not applied correctly. This issue has now been fixed.

TSAC-7109 Steel components

Gusset+ T: The stiffener chamfer is now created to the web of the main part.

TSAC-7332 Steel components

Base plate (1042): Previously, the component was not rotated when you changed the Up direction on the General tab. This issue has now been fixed.

TSAC-7418 Steel components

Column seating (39): Previously, bolts were not created for specific main part profile and bolt horizontal offset combinations. This issue has now been fixed.

TSAC-7436 Steel components

UltraZED Non-std side rail (91): Previously, counterforming both sets of bolts reduced the strut length at one end. This issue has now been fixed.

TSAC-7484 Steel components

Stiffened end plate (27): Previously, finger shim plates were created incorrectly in some cases. This issue has now been fixed.

TSAC-7485 Steel components

End plate (144): Previously, finger shim plates were created incorrectly in some cases. This issue has now been fixed.

TSAC-7490 Steel components

Stiffened end plate (27): Previously, one of the shear tab corner chamfers was not created correctly. This issue has now been fixed.

TTSD-56336 Organizer

Previously, category properties did not open if the environment or model did not have any Organizer filters. This issue has now been fixed.

TTSD-50237 Import, export, interoperability

Earlier, when you had set XS_BOLT_DUPLICATE_IGNORE to TRUE, and exported a part as DSTV, some holes were not exported because another bolted part had holes in the same location. This issue has now been fixed.
Note that you should not use this advanced option in any new models. Instead, use the No hole option for Special hole type in the Bolt properties.

TTSD-54310, TTSD-52356 Import, export, interoperability

IFC export: Earlier, the IFC export result did not contain the properties for IfcBuilding and IfcBuildingStorey. Now these properties are shown.

TTSD-55847 Import, export, interoperability

IFC export: The Property set definitions dialog box now supports better the creation of the boolean property type. Also, an empty value stays empty when exported, it is no longer forced to TRUE.

TTSD-56527 Import, export, interoperability

Reference models: Sometimes the reference model list stopped responding when you scrolled the list in a certain use case. This issue has now been fixed.

TPLED-273 Templates and reports

Template Editor: Copying and pasting a text object that has the '$' character as its only content fails. This issue has now been fixed.

TPLED-276 Templates and reports

Template Editor: Sometimes, when you moved multiple objects horizontally using the Move Object dialog box, the objects also moved vertically. This issue has now been fixed.

TSAC-7059 Drawings

The macros for relabeling section views and detail views are now able to handle views named with numbers correctly.

TTSD-38607 Drawings

Earlier, when using a bolt hole mark with a template attribute in single-part drawing views, the main part hole information was always shown even though the secondary part had a different hole. This issue has now been fixed.

TTSD-51592 Drawings

Fabrication drawings: The Creation review dialog box now supports some advanced options better for concrete parts.

TTSD-55912 Drawings

Reference models in drawings: The DWG reference model texts in drawings are now drawn correctly also when the Outline representation is used.

TTSD-55840 Reinforcement

Rebar sets: Previously, for a tapered rebar set bar group with two or more legs, at the point where the height became greater than the width (or vice versa), the leg dimensions in reports swapped around (DIM_A became DIM_B, and vice versa). This issue has now been fixed.

TTSD-25622 Modeling

In the UK environment, the calculated weights of the profiles UB533x165x66 and UB533x165x75 were incorrect due to the cross sectional area being incorrect in the profile catalog. This issue has now been fixed.

TTSD-55548 Modeling

Bolts: Earlier, in Tekla Structures 2022, if you modeled a bolt that went through two or more parts and that had a negative cut length, the bolt was placed incorrectly. This issue has now been fixed.

TTSD-55674 Modeling

Previously, an empty cross section for weld preparation could cause Tekla Structures to stop working unexpectedly. This has now been fixed.

TTSD-55968 Modeling

Rebar assemblies: The Locked user-defined attribute has now been added for rebar assemblies.

TTSD-56274 Modeling

Bolts: Earlier, in Tekla Structures 2022, bolts were incorrectly positioned when beams or columns were deformed by shortening. The incorrect positioning occurred when XS_DRAW_BOLTS_3D_IN_BOLT_LAYER was set to TRUE and when the bolts had the Exact representation in model views. This issue has now been fixed.

TTSD-56351 Tools and components

Previously, when a formula or equation for a sub-object was removed in Custom component browser, it became visible again after clicking Refresh. This has now been fixed.

TTSD-56576 Tools and components


Previously, Tekla Structures occasionally shut down after a custom component was edited. This has now been fixed.

TSAC-7215 Import, export, interoperability (concrete)

Export ELiPLAN file (68): The export of complex walls created by multiple concrete parts has been improved.

TSAC-7373 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Previously, duplicated records were exported for filled cores. This issue has now been fixed.

TSAC-7453 Import, export, interoperability (concrete)

Export ELiPLAN file (68): Previously, the data conversion file mapping did not work for profiles that had parentheses in the profile name. This issue has now been fixed.

TSAC-7515 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, loose reinforcement was exported as mesh. This issue has now been fixed.

Fanden Sie das hilfreich?
Zurück
Weiter