Engineering library update - October 2022

Tekla Tedds
2022
Tekla Tedds Tekla Tedds for Word

Engineering library update - October 2022

Tekla Tedds engineering library update (October 2022 - version 24.07) is available in Tekla Downloads.

American Design

Wood shear wall design (NDS)

Updated in accordance with the Special Design Provisions for Wind and Seismic 2021.

Retaining wall analysis & design (ACI318/TMS/MSJC)

Enhanced the calculation to include a Calc API so the calculation can be used in automation scenarios including the option to completely disable the user interface. The batch design has also been updated to include a Retaining wall stability analysis example.


Product bulletin October 2022 (PBT-2210-1)

Wind loading (ASCE7) - Fixed a potentially un-conservative error when determining the negative external parapet pressures of a monoslope roof pitch of less than 3 degrees when using the C&C method to ASCE7-16. For more detailed information please refer to Product bulletin October 2022 (PBT-2210-1).

Product bulletin September 2022 (PBT-2209-1)

Wood shear wall design (NDS) - Fixed a potentially un-conservative error affecting wood shear wall designs using a seismic deflection amplification factor other than 4. For more detailed information please refer to Product bulletin September 2022 (PBT-2209-1).

Other Updates

 
Batch design
  Enhanced to include examples for "Retaining wall analysis & design (EN1992/EN1996/EN1997) - Stability analysis"
TEDDS-7122 Fixed the batch design examples for "Footing strip design (ACI318)" and "Footing pad design (ACI31)" to work with the latest version of the "Footing analysis & design (ACI318)" calculation which includes the option to include a parapet.
 
Footing analysis & design (ACI318)
TEDDS-7122 Fixed batch design example and added variable documentation.
TEDDS-6576 Corrected undefined variable, qmax, error.
 
Wood shear wall design (NDS)
TEDDS-941 Corrected disabling of wind service factor.
TEDDS-2878 Enhanced calculation to include compression chord bearing check at bottom plate.
TEDDS-6330 Corrected undefined variable, r, error.
TEDDS-6697 Added Sheathing over gypsum, 3/8 in, 10d nails sheathing option.
 
Wind loading (ASCE7)
TEDDS-6700 Enhanced the calculation to allow user defined topography factors for the C&C method, envelope method and for open buildings and signs/walls to the directional method.
TEDDS-3043 Enhanced the calculation to report the overall roof forces to be set as load case specific variables for use in further calculations.
TEDDS-2602 Added rise to span ratio in output for arched roofs.
TEDDS-2597 Added the end zone length, a, for C&C method calculations
TEDDS-2595 Added option to use exception in Chapter 30 Part 3 for h greater than 60ft and less than 90ft with a height to width ratio of one or less when designing to the C&C method.

Australian Design

Retaining wall analysis & design (AS4678/AS3600/AS3700)

Enhanced the calculation to include a Calc API so the calculation can be used in automation scenarios including the option to completely disable the user interface. The batch design has also been updated to include a Retaining wall stability analysis example.

 
Batch design
  Enhanced to include examples for "Retaining wall analysis & design (AS4678/AS3600/AS3700) - Stability analysis"

British Design

Highway design (DMRB)

New calculation which specifies the design of new pavement and foundation construction in accordance with the Design Manual for Roads and Bridges.

Footway and cycleway design (DMRB)

New calculation which specifies the design of new footway and cycleway in accordance with the Design Manual for Roads and Bridges.

Design traffic assessment (DMRB)

New calculation which calculates traffic loading for the design of road pavements in accordance with the Design Manual for Roads and Bridges.

Estimate California bearing ratio (TRRL LR 1132)

New calculation which estimates the California Bearing Ratio (CBR) value of the formation level using the method outlined in Appendix C of the Transport and Road Research Laboratory (TRRL) laboratory report TRRL LR 1132.

Canadian Design

No updates.

Eurocode Design

Steel beam splice design (EN1993)

New calculation which checks the design of a steel beam splice connection for cover plates and end plates between two identical steel sections subject to bending, shear and axial force. The design is in accordance with EN1993 and the national annexes for the UK, Ireland, Singapore, Malaysia, Finland, Norway, Sweden or the recommended Eurocode values.

Steel column splice design (EN1993)

New calculation which checks the design of a column splice connection for both bearing and non-bearing cover plates, and end plates subject to moments, axial forces, and structural integrity (tying force). The design is in accordance with EN1993 and the national annexes for the UK, Ireland, Singapore, Malaysia, Finland, Norway, Sweden or the recommended Eurocode values.

Steel hollow section tension only splice design (EN1993)

New calculation which checks the design of a hollow section tension only splice connection with end plates subject to tension axial forces only. The design is in accordance with EN1993 and the national annexes for the UK, Ireland, Singapore, Malaysia, Finland, Norway, Sweden or the recommended Eurocode values.

Retaining wall analysis & design (EN1992/EN1996/EN1997)

Enhanced the calculation to include a Calc API so the calculation can be used in automation scenarios including the option to completely disable the user interface. The batch design has also been updated to include a Retaining wall stability analysis example.


Other updates

 
Batch design
 

Enhanced to include examples for:

Retaining wall analysis & design (EN1992/EN1996/EN1997) - Stability analysis

Steel beam splice design (EN1993)

Steel column splice design (EN1993)

Steel hollow section tension only splice design (EN1993)

Retaining wall analysis & design (EN1992/EN1996/EN1997)- Stability analysis

 
Steel column design (EN1993)
TEDDS-7093 Fixed output not being created when the calculations user interface is completely disabled.
 
RC beam design (EN1992)
  Added French national Annex.
 
RC column design (EN1992)
  Added French national Annex.
Bylo to užitečné?
Předchozí
Další